BS EN 1115-1:2001
Withdrawn
View Superseded by
Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) General
Hardcopy , PDF
English
06-15-2001
10-29-2018
Foreword
Introduction
1 Scope
2 Normative references
Annex B (informative)
Bibliography
Describes the general aspects of glass-reinforced thermosetting plastics based on unsaturated polyester resin (GRP-UP) piping systems in the field of underground drainage and sewerage under pressure.
| Committee |
PRI/88
|
| DevelopmentNote |
Supersedes 93/309424 DC. (07/2005)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN EN 1115-1 : 1998 | Identical |
| I.S. EN 1115-1:1998 | Identical |
| NBN EN 1115-1 : 1998 | Identical |
| EN 1115-1 : 1997 | Identical |
| NF EN 1115-1 : 1998 | Identical |
| NS EN 1115-1 : 1ED 1998 | Identical |
| UNE-EN 1115-1:1998 | Identical |
| DIN EN 1115-1:1998-02 | Identical |
| ISO 7511:1999 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the leaktightness of the wall under short-term internal pressure |
| ISO 7510:2017 | Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents |
| EN 1115-5 : 1996 | PLASTICS PIPING SYSTEMS FOR UNDERGROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESINS (UP) - FITNESS FOR PURPOSE OF THE JOINTS |
| EN 1225 : 1996 | PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES - DETERMINATION OF THE CREEP FACTOR OF THE LONG-TERM SPECIFIC RING STIFFNESS |
| ISO 7370:1983 | Glass fibre reinforced thermosetting plastics (GRP) pipes and fittings — Nominal diameters, specified diameters and standard lengths |
| PREN 681-1 : DRAFT 2016 | ELASTOMERIC SEALS - MATERIAL REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER |
| ISO 8639:2016 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness and proof of structural design of flexible joints |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| EN 1115-3 : 1996 | PLASTICS PIPING SYSTEMS FOR UNDERGROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - FITTINGS |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| ISO 8533:2003 | Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints |
| ISO 2078:1993 | Textile glass — Yarns — Designation |
| ISO 10466:1997 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test method to prove the resistance to initial ring deflection |
| EN 1228:1996 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness |
| ISO 7684:1997 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the creep factor under dry conditions |
| ISO 10952:2014 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
| ISO 8572:1991 | Pipes and fittings made of glass-reinforced thermosetting plastics (GRP) — Definitions of terms relating to pressure, including relationships between them, and terms for installation and jointing |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.