DEFSTAN 80-16/5(2011) : 2011
Withdrawn
PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE - TYPE 1: HIGH VISCOSITY (BRUSHING) - TYPE 2: LOW VISCOSITY (SPRAYING)
English
01-01-2011
05-15-2016
Foreword
0 Introduction
1 Scope
2 Warning
3 Normative References
4 Abbreviations
5 Description
6 Information to be Supplied by the Purchaser
7 Keeping Qualities
8 Quality Assurance
9 Product Conformity Certification
10 Containers and Marking of Containers
11 Composition
12 Testing
Annex A - Determination of Viscosity
Annex B - Determination of Rate of Evaporation
Annex C - Determination of Freedom from Corrosive Action
Annex D - Determination of Paint Removing Power
Annex E - Determination of Flammability
Annex F - Determination of Water Rinsability
Annex G - Determination of Stress Corrosion Cracking
Annex H - Determination of Resistance to Hydrogen Embrittlement
Describes the requirements for a dichloromethane water rinsable paint remover in two Types: - Type 1, High Viscosity (Brushing); and - Type 2, Low Viscosity (Spraying).
| DevelopmentNote |
Supersedes DEFSTAN 80-16/4(2006). (05/2011) This standard is obsolescent because it is no longer required for procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (05/2016)
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Withdrawn
|
| Supersedes |
| BS EN ISO 1514:2004 | Paints and varnishes. Standard panels for testing |
| BS EN ISO 1518:2001 | Paints and varnishes. Scratch test |
| BS EN ISO 1513:1995 | Paints and varnishes. Examination and preparation of samples for testing |
| BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
| BS EN 23270:1991 | Specification for temperatures and humidities for conditioning and testing paints, varnishes and their raw materials |
| BS EN ISO 7539-5:1995 | Corrosion of metals and alloys. Stress corrosion testing Method for the preparation and use of C-ring specimens |
| BS EN ISO/IEC 17050-2:2004 | Conformity assessment. Supplier\'s declaration of conformity Supporting documentation |
| BS X 34:1992 | Specification for air drying, two component, polyurethane finish for aerospace purposes |
| BS EN 2832:1993 | Hydrogen embrittlement of steels. Notched specimen test |
| BS EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions |
| BS ISO 3116:2007 | Magnesium and magnesium alloys. Wrought magnesium alloys |
| BS EN 1652:1998 | Copper and copper alloys. Plate, sheet, strip and circles for general purposes |
| BS 2L 500:1973 | Procedure for inspection and testing of wrought magnesium-base alloys |
| BS X 33:1991 | Specification for two component epoxy primer for aerospace purposes |
| BS EN 2395:2005 | Aerospace series. Aluminium alloy AL-P2014A-T4 or T42. Sheet and strip. 0,4 mm ≤a ≤6 mm |
| DEFSTAN 03-2/5(2009) : 2009 | CLEANING AND PREPARATION OF METAL SURFACES |
| BS L 168:1978 | Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS EN ISO/IEC 17050-1:2010 | Conformity assessment. Suppliers declaration of conformity General requirements |
| BS EN 2334:1997 | Chromic-sulphuric acid pickle of aluminium and aluminium alloys |
| DEFSTAN 03-19/4(2010) : 2010 | ELECTRO-DEPOSITION OF CADMIUM |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.