DIN EN 10025-6:2009-08
Withdrawn
View Superseded by
HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION
Hardcopy , PDF
English
01-01-2009
10-29-2019
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification and designation
5 Information to be supplied by the purchaser
6 Manufacturing process
7 Requirements
8 Inspection
9 Preparation of samples and test pieces
10 Test methods
11 Marking, labelling, packaging
12 Complaints
13 Options
Annex A (informative) List of corresponding former
designations
Annex B (informative) List of national standards which
correspond with ECSC IC 2 referenced
Annex C (informative) Minimum recommended inside bend radii
for flanging
Bibliography
This standard is included in DIN Handbook 402 E. Defines requirements for flat products of high yield strength alloy special steels.
| DevelopmentNote |
Supersedes DIN EN 10137-2 E (05/2005)
|
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Withdrawn
|
| SupersededBy |
| Standards | Relationship |
| NF EN 10025-6 : 2005 + A1 2009 | Identical |
| NBN EN 10025-6 : 2004 + A1 2009 | Identical |
| NEN EN 10025-6 : 2004 + A1 2009 | Identical |
| BS EN 10025-6 : 2004 | Identical |
| EN 10025-6:2004+A1:2009 | Identical |
| I.S. EN 10025-6:2004 | Identical |
| NS EN 10025-6 : 2004 + A1 2009 | Identical |
| DIN 2874:2002-06 | Flanged steel pipes and flanged steel or cast iron pipes and fittings with PTFE or PFA linings – Technical delivery conditions |
| EN 10162:2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| ISO 14713:1999 | Protection against corrosion of iron and steel in structures — Zinc and aluminium coatings — Guidelines |
| ISO 2566-1:1984 | Steel — Conversion of elongation values — Part 1: Carbon and low alloy steels |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| EN 10020:2000 | Definition and classification of grades of steel |
| CEN/TR 10347:2006 | Guidance for forming of structural steels in processing |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN ISO 14713 : 1999 | PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - ZINC AND ALUMINIUM COATINGS - GUIDELINES |