DOT/FAA/AR-MMPDS-01 : 20030131

Chapter 1
1.0 General
1.1 Purpose and Use of Document
1.2 Nomenclature
1.3 Commonly Used Formulas
1.4 Basic Principles
1.5 Types of Failures
1.6 Columns
1.7 Thin-Walled and Stiffened Thin-Walled Sections
References
Chapter 2
2.0 Steel
2.1 General
2.2 Carbon Steels
2.3 Low-Alloy Steels (AISI Grades and Proprietary Grades)
2.4 Intermediate Alloy Steels
2.5 High-Alloy Steels
2.6 Precipitation and Transformation-Hardening Steels (Stainless)
2.7 Austenitic Stainless Steels
2.8 Element Properties
References
Chapter 3
3.0 Aluminum
3.1 General
3.2 2000 Series Wrought Alloys
3.3 3000 Series Wrought Alloys
3.4 4000 Series Wrought Alloys
3.5 5000 Series Wrought Alloys
3.6 6000 Series Wrought Alloys
3.7 7000 Series Wrought Alloys
3.8 200.0 Series Cast Alloys
3.9 300.0 Series Cast Alloys
3.10 Element Properties
References
Chapter 4
4.0 Magnesium Alloys
4.1 General
4.2 Magnesium-Wrought Alloys
4.3 Magnesium Cast Alloys
4.4 Element Properties
References
Chapter 5
5.0 Titanium
5.1 General
5.2 Unalloyed Titanium
5.3 Alpha and Near-Alpha Titanium Alloys
5.4 Alpha-Beta Titanium Alloys
5.5 Beta, Near-Beta, and Metastable-Beta Titanium Alloys
5.6 Element Properties
References
Chapter 6
6.0 Heat-Resistant Alloys
6.1 General
6.2 Iron-Chromium-Nickel-Base Alloys
6.3 Nickel-Base Alloys
6.4 Cobalt-Base Alloys
References
Chapter 7
7.0 Miscellaneous Alloys and Hybrid Materials
7.1 General
7.2 Beryllium
7.3 Copper and Copper Alloys
7.4 Multiphase Alloys
7.5 Aluminum Alloy Sheet Laminates
References
Chapter 8
8.0 Structural Joints
8.1 Mechanically Fastened Joints
8.2 Metallurgical Joints
8.3 Bearings, Pulleys, and Wire Rope
References
Chapter 9
9.0 Index
9.1 General
9.2 Material, Specification, Testing, and Data Requirements
9.3 Submission of Data
9.4 Substantiation of S-Basis Minimum Properties
9.5 Analysis Procedures for Statistically Computed Minimum
     Static Properties
9.6 Analysis Procedures for Dynamic and Time Dependent Properties
9.7 Analysis Procedures for Structural Joint Properties
9.8 Examples of Data Analysis and Data Presentation for Static
     Properties
9.9 Examples of Data for Dynamic and Time Dependent Properties
9.10 Statistical Tables
Standards and References
A.0 Glossary
    A.1 Abbreviations
    A.2 Symbols
    A.3 Definitions
    A.4 Conversion of U.S. Units of Measure Used in MMPDS
        to SI Units
B.0 Alloy Index
C.0 Specification Index
D.0 Subject Index
E.0 Figure Index

Provide a source of design mechanical and physical properties, and joint allowable. Material property and joint data obtained from tests by material and fastener producers, government agencies, and members of the airframe industry are submitted to MMPDS for review and analysis.