• There are no items in your cart

EN 1090-3:2008

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures

Superseded date

04-17-2019

Published date

06-25-2008

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Specifications and documentation
   4.1 Execution specification
        4.1.1 General
        4.1.2 Execution classes
        4.1.3 Tolerance types
        4.1.4 Tolerance class for shell structures
        4.1.5 Testing and acceptance criteria for welding
   4.2 Constructor's documentation
        4.2.1 Quality documentation
        4.2.2 Quality plan
        4.2.3 Safety during erection
        4.2.4 Execution documentation
5 Constituent products
   5.1 General
   5.2 Identification, inspection documents and traceability
   5.3 Parent material
   5.4 Aluminium products
   5.5 Welding consumables
   5.6 Mechanical fasteners
        5.6.1 Bolts, nuts and plain washers
        5.6.2 Studs
        5.6.3 Rivets
        5.6.4 Self-drilling and self-tapping screws
        5.6.5 Bearings
   5.7 Adhesive bonding
6 Preparation
   6.1 General
   6.2 Identification
   6.3 Handling, storage and transportation
   6.4 Cutting
   6.5 Forming
   6.6 Holing for fasteners
   6.7 Cut outs
   6.8 Full contact bearing surfaces
   6.9 Assemblies
   6.10 Heat treatment
   6.11 Straightening
7 Welding
   7.1 General
   7.2 Welding plan
        7.2.1 Requirement for a welding plan
        7.2.2 Content of a welding plan
   7.3 Welding process
   7.4 Qualification of welding procedures and welding personnel
        7.4.1 Qualification of welding procedures
        7.4.2 Validity of the welding procedure qualification
        7.4.3 Qualification of welders and welding operators
        7.4.4 Welding coordination personnel
   7.5 Preparation and execution of welding
        7.5.1 General
        7.5.2 Joint preparation
        7.5.3 Weather protection
        7.5.4 Assembly for welding
        7.5.5 Temporary attachments
        7.5.6 Tack welds
        7.5.7 Preheating and interpass temperature
        7.5.8 Butt welds
        7.5.9 Slot and plug welds
        7.5.10 Other welds
   7.6 Acceptance criteria
   7.7 Post-weld heat treatment
8 Mechanical fastening and adhesive bonding
   8.1 Joint assembly for mechanical fastening
        8.1.1 Preparation of contact surfaces
        8.1.2 Fit-up
        8.1.3 Preparations of contact surfaces in slip-resistant
              connections
   8.2 Bolted connections
        8.2.1 General
        8.2.2 Bolts
        8.2.3 Fitted bolts
        8.2.4 Countersunk bolts
        8.2.5 Nuts
        8.2.6 Washers
   8.3 Tightening of bolted connections
        8.3.1 Non-preloaded connections
        8.3.2 Preloaded connections
   8.4 Riveting
        8.4.1 General
        8.4.2 Installation of rivets
   8.5 Fastening of cold formed members and sheeting
   8.6 Adhesive bonded connections
9 Erection
   9.1 General
   9.2 Site conditions
   9.3 Erection method statement
   9.4 Supports
   9.5 Execution on site
        9.5.1 Site survey
        9.5.2 Marking
        9.5.3 Handling and storage at site
        9.5.4 Erection methods
        9.5.5 Alignment and grouting
   9.6 Protection of surfaces, cleaning after erection
10 Surface treatment
   10.1 General
   10.2 Protection of the structure and components
   10.3 Protection of contact surfaces and fasteners
        10.3.1 General
        10.3.2 Contact surfaces aluminium-to-aluminium and
               aluminium-to-plastics
        10.3.3 Contact surfaces of aluminium and steel or wood
        10.3.4 Contact surfaces of aluminium and concrete,
               brickwork and plaster, etc.
        10.3.5 Fasteners
        10.3.6 Bonded joints
   10.4 Fire protection
11 Geometrical tolerances
   11.1 Types of tolerances
   11.2 Essential tolerances
        11.2.1 General
        11.2.2 Manufacturing tolerances
        11.2.3 Erection tolerances
   11.3 Functional tolerances
        11.3.1 General
        11.3.2 Manufacturing tolerances
12 Inspection, testing and corrections
   12.1 General
   12.2 Constituent products and components
        12.2.1 Constituent products
        12.2.2 Components
   12.3 Preparation
        12.3.1 Forming
        12.3.2 Geometrical dimensions of components
   12.4 Welding
        12.4.1 Inspection stages
        12.4.2 Methods of inspection and personnel qualification
        12.4.3 Extent of inspection
        12.4.4 Acceptance criteria for welds
        12.4.5 Repair welds
        12.4.6 Inspection of temporary attachment locations
               after removal
   12.5 Mechanical fasteners
        12.5.1 Inspection of connections with non-preloaded bolts
        12.5.2 Inspection of connections with preloaded bolts
        12.5.3 Inspection of riveted connections
   12.6 Adhesive bonding
   12.7 Nonconforming products
        12.7.1 Nonconforming constituent products
        12.7.2 Nonconforming components and structures
Annex A (normative) Required additional information, options to
        be specified and requirements for execution classes
      A.1 List of required information
      A.2 List of options to be specified
      A.3 Requirements related to execution classes
Annex B (informative) Checklist for the content of a quality plan
      B.1 Introduction
      B.2 Content
          B.2.1 Management
          B.2.2 Specification review
          B.2.3 Documentation
          B.2.4 Inspection and testing procedures
Annex C (normative) Cruciform weld test
      C.1 Introduction
      C.2 Test piece
      C.3 Examination and testing
Annex D (normative) Procedure for determination of slip factor
      D.1 The purpose of testing
      D.2 Significant variables
      D.3 Test specimens
      D.4 Slip test procedure and evaluation of results
      D.5 Extended creep test procedure and evaluation
      D.6 Test results
Annex E (informative) Fastening of cold formed members and sheeting
      E.1 General
      E.2 Use of self-tapping and self-drilling screws
      E.3 Use of blind rivets
      E.4 Fastening sidelaps
Annex F (informative) Surface treatment
      F.1 Anodic oxidation
      F.2 Coatings
          F.2.1 General
          F.2.2 Pre-treatment
          F.2.3 Base coat
          F.2.4 Final coat
          F.2.5 Coatings with bitumen or bituminous combinations
          F.2.6 Repair coatings
      F.3 Passivation
Annex G (normative) Geometrical tolerances - Essential tolerances
      G.1 Manufacturing tolerances
          G.1.1 General
          G.1.2 Welded I-sections
          G.1.3 Welded box sections
          G.1.4 Webs
          G.1.5 Components
          G.1.6 Base plates and end plate connections
          G.1.7 Column splices
          G.1.8 Lattice components
      G.2 Erection tolerances
          G.2.1 Columns
          G.2.2 Beams
          G.2.3 Full contact bearing
Annex H (normative) Geometrical tolerances - Functional tolerances
      H.1 General
      H.2 Manufacturing tolerances
          H.2.1 Box sections
          H.2.2 Components
          H.2.3 Stiffeners
          H.2.4 Fastener holes, notches and edges
          H.2.5 Lattice components
      H.3 Erection tolerances
          H.3.1 Columns
          H.3.2 Beams, rafters and trusses
      H.4 Bridges
Annex I (normative) Geometrical tolerances - Shell structures
      I.1 General
      I.2 Out-of roundness tolerances
      I.3 Non-intended eccentricity due to execution
      I.4 Dent tolerances
      I.5 Interface flatness tolerances
Annex J (informative) Designation of requirements to welds on
        drawings
      J.1 General
      J.2 Global specification
      J.3 Specific designations for welds, part of welds, details
Annex K (informative) Recommendations for description of site
        conditions and erection in the execution specification
      K.1 Site conditions
      K.2 Erection method statement
Annex L (informative) Guide for preparation of the execution
        specification for quality requirements of welds
      L.1 General
      L.2 Utilization grades and utilization ranges
          L.2.1 General
          L.2.2 Utilization grade for components and structures
                in service category SC1
          L.2.3 Utilization grade for components and structures
                in service category SC2
      L.3 Extent of additional NDT
          L.3.1 Extent of NDT (%) for components/structures in
                service category SC1
          L.3.2 Extent of additional NDT (%) for
                components/structures in service category SC2
      L.4 Acceptance criteria for welds
          L.4.1 Acceptance criteria for welds in service
                category SC1
          L.4.2 Acceptance criteria for welds in service
                category SC2
Annex M (informative) Guide for specification of quality
        requirements for components and structures in SC2
Annex N (informative) Chart for development and use of a
        welding procedure specification (WPS)
Bibliography

This European Standard specifies requirements for the execution of aluminium structural components and structures made from:a)rolled sheet, strip and plate;b)extrusions;c)cold drawn rod, bar and tube;d)forgings;e)castings.NOTE 1The execution of structural components is referred to as manufacturing, in accordance with EN 1090-1.This European Standard specifies requirements independent of the type and shape of the aluminium structure, and this European Standard is applicable to structures under predominantly static loads as well as structures subject to fatigue. It specifies requirements related to the execution classes that are linked with consequence classes.NOTE 2Consequence classes are defined in EN 1990.NOTE 3Recommendations for selection of execution class in relation to consequence class are given in EN 1999-1-1.This European Standard covers components made of constituent products with thickness not less than 0,6 mm for welded components not less than 1,5 mm.This European Standard applies to structures designed according to the relevant parts of EN 1999. If this European Standard is used for structures designed according to other design rules or used for other alloys and tempers not covered by EN 1999, a judgement of the reliability elements in these design rules should be made.This European Standard specifies requirements for surface preparation prior to application of a protective treatment, and gives guidelines for application for such treatment in an informative annex.This European Standard gives options for specifying requirements to match project specific requirements.This European Standard is also applicable to temporary aluminium structures.

Committee
CEN/TC 135
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

UNE-EN 13195:2014 Aluminium and aluminium alloys - Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore)
09/30211977 DC : 0 BS EN 16031 - ADJUSTABLE TELESCOPIC ALUMINIUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS
PD CEN/TR 17052:2017 Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures Requirements for conformity assessment of structural components
14/30304786 DC : 0 BS EN 15048-2 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE
BS EN 1090-5:2017 Execution of steel structures and aluminium structures Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
DIN EN 13195:2013-12 ALUMINIUM AND ALUMINIUM ALLOYS - SPECIFICATIONS FOR WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE)
VDMA 24408 : DRAFT 2015 LIMIT OF THE SCOPE OF THE EUROPEAN CONSTRUCTION PRODUCTS REGULATION 305/2011/EU WITH RESPECT TO PROCESS PLANT AND AMENDMENTS TO HARMONIZED STANDARDS UNDER THE EUROPEAN PRESSURE EQUIPMENT DIRECTIVE
DIN EN 1999-1-4:2010-05 Eurocode 9 - Design of aluminium structures - Part 1-4: Cold-formed structural sheeting (includes Corrigendum AC:2009)
UNI EN 1999-1-5 : 2007 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-5: SHELL STRUCTURES
UNI EN 1090-1 : 2012 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS
EN 15048-1:2016 Non-preloaded structural bolting assemblies - Part 1: General requirements
DIN EN 1090-5:2017-07 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
EN 13195:2013 Aluminium and aluminium alloys - Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore)
CEN/TR 17052:2017 Guidelines on implementing EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
CEN/TR 1317-6:2012 Road restraint systems - Part 6: Pedestrian restraint system - Pedestrian parapets
EN 1090-1:2009+A1:2011 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
EN 12812:2008 Falsework - Performance requirements and general design
DIN EN 16031:2012-09 ADJUSTABLE TELESCOPIC ALUMINUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS
14/30312146 DC : 0 BS EN 1090-5 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR THIN-GAUGE, COLD-FORMED ALUMINIUM ELEMENTS AND STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
UNI EN 13195 : 2013 ALUMINIUM AND ALUMINIUM ALLOYS - SPECIFICATIONS FOR WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE)
BS EN 1090-1 : 2009 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS
UNE-EN 15048-1:2018 Non-preloaded structural bolting assemblies - Part 1: General requirements
BS EN 16031:2012 Adjustable telescopic aluminium props. Product specifications, design and assessment by calculation and tests
PD CEN/TR 16949:2016 Road restraint system. Pedestrian restraint system. Pedestrian parapets
UNE-EN 1090-1:2011 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components
CEN/TR 16949:2016 Road restraint system - Pedestrian restraint system - Pedestrian parapets
BS EN 1999-1-2:2007 Eurocode 9. Design of aluminium structures Structural fire design
PREN 13107 : DRAFT 2013 SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS
S.R. CEN/TR 17052:2017 GUIDELINES ON IMPLEMENTING EN 1090-1:2009+A1:2011, EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS
UNI CEN/TR 1317-6 : 2012 ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
ABS 0236 : 2016 GUIDE FOR CERTIFICATION OF OFFSHORE ACCESS GANGWAYS
I.S. EN 1999-1-1:2007 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES (INCLUDING IRISH NATIONAL ANNEX)
BS EN 1999-1-1 : 2007 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES
I.S. EN 15048-1:2016 NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS
UNE-EN 1090-5:2017 Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
PREN 17206 : DRAFT 2018 ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS)
UNE-EN 15048-2:2017 Non-preloaded structural bolting assemblies - Part 2: Fitness for purpose
BS EN 15048-1:2007 Non-preloaded structural bolting assemblies General requirements
I.S. EN 12812:2008 FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN
I.S. EN 13107:2015 SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS
I.S. EN 15048-2:2016 NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE
DIN EN 1999-1-1:2014-03 Eurocode 9: Design of aluminium structures - Part 1-1: General structural rules
PD CEN/TR 1317-6:2012 Road restraint systems Pedestrian restraint system. Pedestrian parapets
DIN EN 1999-1-5:2010-05 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-5: SHELL STRUCTURES
BS EN 1999-1-4 : 2007 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-4: COLD-FORMED STRUCTURAL SHEETING
ISO/TS 20273:2017 Guidelines on weld quality in relationship to fatigue strength
13/30275585 DC : 0 BS EN 13107 - SAFETY REQUIREMENTS FOR CABLEWAY INSTALLATIONS DESIGNED TO CARRY PERSONS - CIVIL ENGINEERING WORKS
16/30328759 DC : 0 BS EN 13814-1 - SAFETY OF AMUSEMENT RIDES AND AMUSEMENT DEVICES - PART 1: DESIGN AND MANUFACTURE
I.S. EN 16031:2012 ADJUSTABLE TELESCOPIC ALUMINIUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS
S.R. CWA 15902-2:2009 LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - PART 2: SPECIFICATIONS FOR DESIGN, MANUFACTURE AND FOR USE OF ALUMINIUM AND STEEL TRUSSES AND TOWERS
UNI EN 1999-1-4 : 2011 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-4: COLD-FORMED STRUCTURAL SHEETING
I.S. EN 1993-4-1:2007 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 4-1: SILOS
DIN EN 12812:2008-12 FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN
EEMUA 207 : 2009 DOUBLE CONCRETE TANKS FOR LIQUEFIED GAS - GUIDE TO DESIGN, CONSTRUCTION AND OPERATION
UNI EN 1993-1-9 : 2005 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-9: FATIGUE
UNI EN 12812 : 2008 FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN
UNI EN 1999-1-2 : 2007 EUROCODE 9 - DESIGN OF ALUMINIUM STRUCTURES - PART 1-2: STRUCTURAL FIRE DESIGN
UNI EN 1999-1-1 : 2014 EUROCODE 9: DESIGN OF ALUMINIUM STRUCTURES - PART 1-1: GENERAL STRUCTURAL RULES
BS EN 13195:2013 Aluminium and aluminium alloys. Specifications for wrought and cast products for marine applications (shipbuilding, marine and offshore)
DIN EN 1999-1-2:2010-12 Eurocode 9: Design of aluminium structures - Part 1-2: Structural fire design (includes Corrigendum AC:2009)
PD ISO/TS 20273:2017 Guidelines on weld quality in relationship to fatigue strength
PREN 15048-2 : DRAFT 2014 NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE
UNI EN 16031 : 2012 ADJUSTABLE TELESCOPIC ALUMINIUM PROPS - PRODUCT SPECIFICATIONS, DESIGN AND ASSESSMENT BY CALCULATION AND TESTS
PREN 13031-1 : DRAFT 2017 GREENHOUSES - DESIGN AND CONSTRUCTION - PART 1: COMMERCIAL PRODUCTION GREENHOUSES
I.S. EN 13195:2013 ALUMINIUM AND ALUMINIUM ALLOYS - SPECIFICATIONS FOR WROUGHT AND CAST PRODUCTS FOR MARINE APPLICATIONS (SHIPBUILDING, MARINE AND OFFSHORE)
DIN EN 15048-1:2016-09 NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS
DIN EN 15048-2:2016-09 NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE
BS EN 13107:2015 Safety requirements for cableway installations designed to carry persons. Civil engineering works
BS EN 12812:2008 Falsework. Performance requirements and general design
BS EN 15048-2:2007 Non-preloaded structural bolting assemblies Suitability test
17/30326406 DC : 0 BS EN 17168 - RAILWAY APPLICATIONS - PLATFORM BARRIER SYSTEMS
EN 15048-2:2016 Non-preloaded structural bolting assemblies - Part 2: Fitness for purpose
EN 16031:2012 Adjustable telescopic aluminium props - Product specifications, design and assessment by calculation and tests
S.R. CEN/TR 1317-6:2012 ROAD RESTRAINT SYSTEMS - PART 6: PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
18/30366946 DC : 0 BS EN 17206 - ENTERTAINMENT TECHNOLOGY - LIFTING AND LOAD-BEARING EQUIPMENT FOR STAGES AND OTHER PRODUCTION AREAS WITHIN THE ENTERTAINMENT INDUSTRY - SPECIFICATIONS FOR GENERAL REQUIREMENTS (EXCLUDING ALUMINUM AND STEEL TRUSSES AND TOWERS)
BS EN 1999-1-5:2007 Eurocode 9. Design of aluminium structures Shell structures
NORSOK C-004:2013 HELICOPTER DECK ON OFFSHORE INSTALLATIONS
KTA 3205.2 : 2015 COR 2016 COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT
I.S. EN 1090-1:2009 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 1: REQUIREMENTS FOR CONFORMITY ASSESSMENT OF STRUCTURAL COMPONENTS
UNE-EN 16031:2013 Adjustable telescopic aluminium props - Product specifications, design and assessment by calculation and tests
S.R. CEN/TR 16949:2016 ROAD RESTRAINT SYSTEM - PEDESTRIAN RESTRAINT SYSTEM - PEDESTRIAN PARAPETS
17/30354665 DC : 0 BS EN 13031-1 - GREENHOUSES - DESIGN AND CONSTRUCTION - PART 1: COMMERCIAL PRODUCTION GREENHOUSES
I.S. EN 1090-5:2017 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 5: TECHNICAL REQUIREMENTS FOR COLD-FORMED STRUCTURAL ALUMINIUM ELEMENTS AND COLD-FORMED STRUCTURES FOR ROOF, CEILING, FLOOR AND WALL APPLICATIONS
EN 1090-5:2017 Execution of steel structures and aluminium structures - Part 5: Technical requirements for cold-formed structural aluminium elements and cold-formed structures for roof, ceiling, floor and wall applications
DIN EN 1999-1-5:2017-03 Eurocode 9 - Design of aluminium structures - Part 1-5: Shell structures (includes Corrigendum 5:2009)
DIN EN 1090-1:2012-02 Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components (includes Amendment A1:2011)

EN ISO 1479:2011 Hexagon head tapping screws (ISO 1479:2011)
ISO 10511:2012 Prevailing torque type hexagon thin nuts (with non-metallic insert)
ISO 8839:1986 Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals
EN ISO 15981:2002 Open end blind rivets with break pull mandrel and protruding head - AIA/AIA (ISO 15981:2002)
ISO 9018:2015 Destructive tests on welds in metallic materials Tensile test on cruciform and lapped joints
EN 14399-8:2007 High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies
EN ISO 6520-1:2007 Welding and allied processes - Classification of geometric imperfections in metallic materials - Part 1: Fusion welding (ISO 6520-1:2007)
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
ISO 7090:2000 Plain washers, chamfered Normal series Product grade A
EN ISO 15481:1999 Cross recessed pan head drilling screws with tapping screw thread (ISO 15481:1999)
EN 485-1:2016 Aluminium and aluminium alloys - Sheet, strip and plate - Part 1: Technical conditions for inspection and delivery
EN ISO 3834-3:2005 Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2005)
ISO 2553:2013 Welding and allied processes Symbolic representation on drawings Welded joints
EN 1337-6:2004 Structural bearings - Part 6: Rocker bearings
EN 755-1:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery
EN ISO 10511:2012 Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012)
ISO 13918:2008 Welding Studs and ceramic ferrules for arc stud welding
EN 754-3:2008 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form
ISO 15974:2000 Closed end blind rivets with break pull mandrel and countersunk head AlA/St
ISO 15480:1999 Hexagon washer head drilling screws with tapping screw thread
EN ISO 7049:2011 Cross-recessed pan head tapping screws (ISO 7049:2011)
ISO 6520-1:2007 Welding and allied processes Classification of geometric imperfections in metallic materials Part 1: Fusion welding
EN 754-7:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form
ISO 1479:2011 Hexagon head tapping screws
EN ISO 3834-2:2005 Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005)
EN ISO 7091:2000 Plain washers - Normal series - Product grade C (ISO 7091:2000)
EN 755-5:2008 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form
EN ISO 6789:2003 Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003)
EN ISO 7040:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012)
EN 1301-1:2008 Aluminium and aluminium alloys - Drawn wire - Part 1: Technical conditions for inspection and delivery
ISO 13920:1996 Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position
EN 14399-3:2015 High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
ISO 9606-2:2004 Qualification test of welders — Fusion welding — Part 2: Aluminium and aluminium alloys
EN ISO 7093-2:2000 Plain washers - Large series - Part 2: Product grade C (ISO 7093-2:2000)
ISO 7042:2012 Prevailing torque type all-metal hexagon high nuts — Property classes 5, 8, 10 and 12
ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs
ISO 10042:2005 Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections
ISO 3834-4:2005 Quality requirements for fusion welding of metallic materials Part 4: Elementary quality requirements
EN ISO 15613:2004 Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004)
EN 573-2:1994 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 2: Chemical symbol based designation system
ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials Welding procedure test Part 2: Arc welding of aluminium and its alloys
ISO 10642:2004 Hexagon socket countersunk head screws
EN 1321:1996 Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds
EN ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009)
EN ISO 4288:1997 Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (ISO 4288:1996)
EN 485-3:2003 Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products
EN ISO 15612:2004 Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004)
EN 755-9:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form
ISO 4016:2011 Hexagon head bolts Product grade C
EN ISO 3834-4:2005 Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements (ISO 3834-4:2005)
EN ISO 7042:2012 Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012)
EN ISO 15977:2002 Open end blind rivets with break pull mandrel and protruding head - AIA/St (ISO 15977:2002)
ISO 4034:2012 Hexagon regular nuts (style 1) Product grade C
CR ISO 17663 : 2001 WELDING - GUIDELINES FOR QUALITY REQUIREMENTS FOR HEAT TREATMENT IN CONNECTION WITH WELDING AND ALLIED PROCESSES
EN ISO 1481:2011 Slotted pan head tapping screws (ISO 1481:2011)
EN 485-4:1993 Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products
EN 755-3:2008 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 3: Round bars, tolerances on dimensions and form
ISO 2320:2015 Fasteners Prevailing torque steel nuts Functional properties
EN ISO 7090:2000 Plain washers, chamfered - Normal series - Product grade A (ISO 7090:2000)
ISO 17123-7:2005 Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 7: Optical plumbing instruments
ISO 10509:2012 Hexagon flange head tapping screws
EN 1011-1:2009 Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding
ISO 14731:2006 Welding coordination Tasks and responsibilities
EN ISO 7719:2012 Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012)
ISO 7049:2011 Cross-recessed pan head tapping screws
EN 755-8:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form
ISO 7976-2:1989 Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points
EN ISO 2009:2011 Slotted countersunk flat head screws - Product grade A (ISO 2009:2011)
EN ISO 4063:2010 Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01)
EN 755-4:2008 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form
ISO/TR 17663:2001 Welding Guidelines for quality requirements for heat treatment in connection with welding and allied processes
EN ISO 7093-1:2000 Plain washers - Large series - Part 1: Product grade A (ISO 7093-1:2000)
ISO 4017:2014 Fasteners Hexagon head screws Product grades A and B
EN ISO 4016:2011 Hexagon head bolts - Product grade C (ISO 4016:2011)
EN ISO 4014:2011 Hexagon head bolts - Product grades A and B (ISO 4014:2011)
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
ISO 4032:2012 Hexagon regular nuts (style 1) — Product grades A and B
ISO 18273:2015 Welding consumables Wire electrodes, wires and rods for welding of aluminium and aluminium alloys Classification
EN 586-3:2001 Aluminium and aluminium alloys - Forgings - Part 3: Tolerances on dimensions and form
ISO 9013:2017 Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances
EN 755-7:2016 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form
EN ISO 9018:2015 Destructive tests on welds in metallic materials - Tensile test on cruciform and lapped joints (ISO 9018:2015)
EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
ISO 17123-3:2001 Optics and optical instruments Field procedures for testing geodetic and surveying instruments Part 3: Theodolites
ISO 15481:1999 Cross recessed pan head drilling screws with tapping screw thread
EN 1337-8:2007 Structural bearings - Part 8: Guide Bearings and Restraint Bearings
EN 1301-3:2008 Aluminium and aluminium alloys - Drawn wire - Part 3: Tolerances on dimensions
EN 754-6:2008 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form
ISO 15612:2004 Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure
EN 755-6:2008 Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form
ISO 4762:2004 Hexagon socket head cap screws
EN 1337-11:1997 Structural bearings - Part 11: Transport, storage and installation
ISO 15977:2002 Open end blind rivets with break pull mandrel and protruding head — AIA/St
EN ISO 4018:2011 Hexagon head screws - Product grade C (ISO 4018:2011)
ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding
EN ISO 13920:1996 Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996)
ISO 15978:2002 Open end blind rivets with break pull mandrel and countersunk head — AIA/St
ISO 1481:2011 Slotted pan head tapping screws
EN 12373-1 : 2001 ALUMINIUM AND ALUMINIUM ALLOYS - ANODIZING - PART 1: METHOD FOR SPECIFYING DECORATIVE AND PROTECTIVE ANODIC OXIDATION COATINGS ON ALUMINIUM
ISO 7089:2000 Plain washers Normal series Product grade A
ISO 3834-2:2005 Quality requirements for fusion welding of metallic materials Part 2: Comprehensive quality requirements
EN 1706:2010 Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties
EN ISO 15974:2000 Closed end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15974:2000)
ISO 4463-1:1989 Measurement methods for building — Setting-out and measurement — Part 1: Planning and organization, measuring procedures, acceptance criteria
ISO 7719:2012 Prevailing torque type all-metal hexagon regular nuts — Property classes 5, 8 and 10
ISO 15973:2000 Closed end blind rivets with break pull mandrel and protruding head AlA/St
ISO 2009:2011 Slotted countersunk flat head screws Product grade A
EN 22553:1994 Welded, brazed and soldered joints - Symbolic representation on drawings (ISO 2553:1992)
EN ISO 15614-2:2005 Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 2: Arc welding of aluminium and its alloys (ISO 15614-2:2005)
ISO 7091:2000 Plain washers Normal series Product grade C
EN 754-1:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery
EN ISO 2320:2015 Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015)
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
EN ISO 10513:2012 Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012)
EN 1559-1:2011 Founding - Technical conditions of delivery - Part 1: General
ISO 10513:2012 Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread — Property classes 8, 10 and 12
EN 14399-6:2015 High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers
EN 515:2017 Aluminium and aluminium alloys - Wrought products - Temper designations
ISO 10512:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread — Property classes 6, 8 and 10
EN 754-5:2008 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form
ISO 7040:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) — Property classes 5, 8 and 10
EN ISO 7046-2:2011 Countersunk flat head screws (common head style) with type H or type Z cross recess - Product grade A - Part 2: Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws (ISO 7046-2:2011)
EN ISO 18273:2015 Welding consumables - Wire electrodes, wires and rods for welding of aluminium and aluminium alloys - Classification (ISO 18273:2015)
EN 1337-3:2005 Structural bearings - Part 3: Elastomeric bearings
EN ISO 14731:2006 Welding coordination - Tasks and responsibilities (ISO 14731:2006)
EN 10204:2004 Metallic products - Types of inspection documents
EN 586-1:1997 Aluminium and aluminium alloys - Forgings - Part 1: Technical conditions for inspection and delivery
EN ISO 4017:2014 Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2014)
EN ISO 15609-1:2004 Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004)
EN 754-8:2016 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form
EN 14399-4:2015 High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies
EN ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013)
EN 1090-2:2008+A1:2011 Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
ISO 7976-1:1989 Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments
ISO 6789:2003 Assembly tools for screws and nuts Hand torque tools Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure
EN 12206-1:2004 Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1: Coatings prepared from coating powder
EN 14399-7:2007 High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies
EN ISO 4032:2012 Hexagon regular nuts (style 1) - Product grades A and B (ISO 4032:2012)
ISO 7093-2:2000 Plain washers Large series Part 2: Product grade C
EN 14399-5:2015 High-strength structural bolting assemblies for preloading - Part 5: Plain washers
ISO 15613:2004 Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test
ISO 4063:2009 Welding and allied processes — Nomenclature of processes and reference numbers
EN ISO 15480:1999 Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999)
EN 1559-4:2015 Founding - Technical conditions of delivery - Part 4: Additional requirements for aluminium alloy castings
ISO 17123-4:2012 Optics and optical instruments — Field procedures for testing geodetic and surveying instruments — Part 4: Electro-optical distance meters (EDM measurements to reflectors)
EN 28839:1991 Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986)
EN ISO 9013:2017 Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017)
EN 571-1:1997 Non destructive testing - Penetrant testing - Part 1: General principles
ISO 17123-1:2014 Optics and optical instruments — Field procedures for testing geodetic and surveying instruments — Part 1: Theory
EN 1418:1997 Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials
EN ISO 7089:2000 Plain washers - Normal series - Product grade A (ISO 7089:2000)
ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts
EN 970:1997 Non-destructive examination of fusion welds - Visual examination
EN 1337-5:2005 Structural bearings - Part 5: Pot bearings
EN ISO 15973:2000 Closed end blind rivets with break pull mandrel and protruding head - AIA/St (ISO 15973:2000)
ISO 15981:2002 Open end blind rivets with break pull mandrel and protruding head — AIA/AIA
EN ISO 15978:2002 Open end blind rivets with break pull mandrel and countersunk head - AIA/St (ISO 15978:2002)
EN 754-4:2008 Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form
ISO 7046-2:2011 Countersunk flat head screws (common head style) with type H or type Z cross recess Product grade A Part 2: Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws
EN ISO 10512:2012 Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012)
EN 573-3:2013 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products
EN ISO 17659:2004 Welding - Multilingual terms for welded joints with illustrations (ISO 17659:2002)
ISO 17659:2002 Welding — Multilingual terms for welded joints with illustrations
EN 573-1:2004 Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 1: Numerical designation system
ISO 3834-3:2005 Quality requirements for fusion welding of metallic materials Part 3: Standard quality requirements
EN ISO 9000:2015 Quality management systems - Fundamentals and vocabulary (ISO 9000:2015)
EN 15088:2005 Aluminium and aluminium alloys - Structural products for construction works - Technical conditions for inspection and delivery
EN 12020-1:2008 Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery
ISO 8062:1994 Castings System of dimensional tolerances and machining allowances
EN ISO 4762:2004 Hexagon socket head cap screws (ISO 4762:2004, Corrected version 2024-08)
EN 14399-2:2015 High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread
ISO 4014:2011 Hexagon head bolts Product grades A and B
ISO 4018:2011 Hexagon head screws Product grade C
EN 1320:1996 Destructive tests on welds in metallic materials - Fracture test
ISO 7093-1:2000 Plain washers Large series Part 1: Product grade A
EN ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009)

Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.