EN ISO 25649-7:2017
Withdrawn
Floating leisure articles for use on and in the water - Part 7: Additional specific safety requirements and test methods for class E devices (ISO 25649-7:2017)
10-11-2017
04-30-2018
European foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Materials
5 Construction and functional components of boats
6 Safety requirements and test methods
7 Performance requirements and test methods for boats
8 Standard equipment and accessories for boats
9 Marking
10 Instructions for use for boats
11 Exclusions
Annex A (normative) - Inflatable canoes, kayaks and
sit-on-top kayaks
Annex B (normative) - Inflatable boat propelled by sail
or motor
Annex C (informative) - General arrangement of a typical
boat with the hull made of non-reinforced material
Annex D (informative) - General arrangement of a typical
boat with the hull made of reinforced material
Annex E (informative) - General arrangement of a typical
paddle boat/kayak
Annex F (informative) - Examples of typical products forming
Class E
Bibliography
ISO 25649-7:2017 is applicable for Class E floating leisure articles for use on and in water according to ISO 25649‑1 regardless whether the buoyancy is achieved by inflation or inherent buoyant material.ISO 25649-7:2017 is applicable with ISO 25649‑1 and ISO 25649‑2.Class E devices are intended for use in bathing areas or in protected and safe shore zones.NOTE 1 Typical products forming Class E (see Annex F):- inflatable boats for rowing or paddling of near oval shape with or without transom;- canoes and kayaks;- inflatable boats made from plastic sheets or from reinforced materials;- motor kit/sail kit as additional option.NOTE 2 Typical places for application of Class E devices:- moving from A to B for pleasure purposes;- staying on the water for relaxing;- moving from shore to the main boat, transportation of persons and load (tender boat).
| Committee |
CEN/TC 136
|
| DevelopmentNote |
Supersedes EN 15649-7. (10/2017)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Withdrawn
|
| Supersedes |
| Standards | Relationship |
| ISO 25649-7:2017 | Identical |
| DIN EN ISO 25649-7 E : 2018 | Identical |
| SS-EN ISO 25649-7:2017 | Identical |
| NS EN ISO 25649-7 : 2017 | Identical |
| PN EN ISO 25649-7 : 2018 | Identical |
| DIN EN ISO 25649-7:2018-04 | Identical |
| I.S. EN ISO 25649-7:2017 | Identical |
| BS EN ISO 25649-7:2017 | Identical |
| NEN EN ISO 25649-7 : 2017 | Identical |
| NF EN ISO 25649-7 : 2017 | Identical |
| DIN EN ISO 25649-7:2015-02 (Draft) | Identical |
| DS EN ISO 25649-7 : 2017 | Identical |
| UNE-EN ISO 25649-7:2018 | Identical |
| EN 13138-3:2014 | Buoyant aids for swimming instruction - Part 3: Safety requirements and test methods for swim seats to be worn |
| ISO 4646:1989 | Rubber- or plastics-coated fabrics — Low-temperature impact test |
| ISO 6185-1:2001 | Inflatable boats — Part 1: Boats with a maximum motor power rating of 4,5 kW |
| EN 13138-2:2014 | Buoyant aids for swimming instruction - Part 2: Safety requirements and test methods for buoyant aids to be held |
| ISO 6185-3:2014 | Inflatable boats — Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing |
| ISO 25649-2:2017 | Floating leisure articles for use on and in the water — Part 2: Consumer information |
| EN 71-1:2014 | Safety of toys - Part 1: Mechanical and physical properties |
| ISO 13857:2008 | Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| ISO 8665:2006 | Small craft — Marine propulsion reciprocating internal combustion engines — Power measurements and declarations |
| ISO 6185-2:2001 | Inflatable boats — Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive |
| ISO 3011:1997 | Rubber- or plastics-coated fabrics — Determination of resistance to ozone cracking under static conditions |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| EN 13138-1:2014 | Buoyant aids for swimming instruction - Part 1: Safety requirements and test methods for buoyant aids to be worn |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |