I.S. EN 13443-1:2002
Withdrawn
WATER CONDITIONING EQUIPMENT INSIDE BUILDINGS - MECHANICAL FILTERS - PART 1: PARTICLE RATING 80 MICROMETER TO 150 MICROMETER - REQUIREMENTS FOR PERFORMANCES, SAFETY AND TESTING
Hardcopy , PDF
English
02-07-2003
10-12-2007
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials (Chemical and hygienic behaviour of materials)
6 General design requirements
7 Performances requirements
8 Performance tests
9 Technical documents, labelling and marking
Annex A (informative) Bibliographical information
Annex B (normative) Installation, operation and maintenance
Bibliography
Defines requirements relating to the construction and mode of operation of filters and describes relevant methods of testing.
| DevelopmentNote |
2002 Edition Re-Issued in October 2007 & incorporates AMD 1 2007. (10/2007)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| NEN EN 13443-1 : 2003 + A1 2007 | Identical |
| NF EN 13443-1 : 2003 + A1 2007 | Identical |
| BS EN 13443-1:2002 | Identical |
| NBN EN 13443-1 : 2003 + A1 2007 | Identical |
| EN 13443-1:2002+A1:2007 | Identical |
| DIN EN 13443-1:2007-12 | Identical |
| NS EN 13443-1 : 2002 + A1 2007 | Identical |
| UNE-EN 13443-1:2003 | Identical |
| ISO 9276-1:1998 | Representation of results of particle size analysis — Part 1: Graphical representation |
| EN 1254-1:1998 | Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| EN 13443-2:2005+A1:2007 | Water conditioning equipment inside buildings - Mechanical filters - Part 2: Particle rating 1 µm to less than 80 µm - Requirements for performance, safety and testing |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| ISO 7005-3:1988 | Metallic flanges — Part 3: Copper alloy and composite flanges |
| EN 15161:2006 | Water conditioning equipment inside buildings - Installation, operation, maintenance and repair |
| EN 1567:1999 | Building valves - Water pressure reducing valves and combination water pressure reducing valves - Requirements and tests |
| EN 1717:2000 | Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow |
| ISO 2591-1:1988 | Test sieving — Part 1: Methods using test sieves of woven wire cloth and perforated metal plate |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation |
| EN 1333:2006 | Flanges and their joints - Pipework components - Definition and selection of PN |
| ISO 6509:1981 | Corrosion of metals and alloys — Determination of dezincification resistance of brass |
| ISO 3822-3:1997 | Acoustics — Laboratory tests on noise emission from appliances and equipment used in water supply installations — Part 3: Mounting and operating conditions for in-line valves and appliances |
| EN ISO 6509:1995 | Corrosion of metals and alloys - Determination of dezincification resistance of brass (ISO 6509:1981) |
| EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
| ISO 13320-1:1999 | Particle size analysis — Laser diffraction methods — Part 1: General principles |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.