ISO 1432:2013
Withdrawn
Withdrawn
View Superseded by
Rubber, vulcanized or thermoplastic — Determination of low-temperature stiffening (Gehman test)
Available format(s)
Hardcopy , PDF
Language(s)
French, English
Published date
01-03-2013
Withdrawn date
04-09-2025
Superseded by
US$96.00
Excluding Tax where applicable
ISO 1432:2013 specifies a static procedure, known as the Gehman test, for determining the relative stiffness characteristics of vulcanized or thermoplastic rubbers over a temperature range from room temperature to approximately −150 °C.
| Committee |
ISO/TC 45/SC 2
|
| DevelopmentNote |
Supersedes ISO/DIS 1432. (01/2013)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| IS 3400 : Part 18 : 2021 | Identical |
| NEN ISO 1432 : 2013 | Identical |
| BS ISO 1432:2013 | Identical |
| NF ISO 1432 : 2013 | Identical |
| UNE-ISO 1432:2013 | Identical |
| UNE 53568:2002 | Identical |
| NBN ISO 1432 : 1990 | Identical |
| NFT 46 025 : 1981 | Similar to |
| BS 903-A13:1983 | Identical |
| SAC GB/T 6036 : 2001 | Identical |
| API SPEC 11D1 : 2015 | PACKERS AND BRIDGE PLUGS |
| BS ISO 24453:2008 | Rubber. Acquisition and presentation of comparable single-point data |
| BS 7825-3.1:1997 | Calibration of rubber and plastics test equipment. Calibration schedules Thermal properties |
| BS 7825-2:1996 | Calibration of rubber and plastics test equipment Calibration procedures |
| 05/30130019 DC : DRAFT JULY 2005 | BS F 154 - PROPERTIES OF FLUOROSILICONE RUBBER SHEET, MOULDINGS AND EXTRUSIONS - SPECIFICATION |
| BS F 156:2006 | Properties of fluid resistant ethylene-propylene rubber sheet, mouldings and extrusions. Specification |
| ISO 17325-2:2014 | Ships and marine technology — Marine environment protection — Oil booms — Part 2: Strength and performance requirements |
| DEFSTAN 02-337(PT1)/2(2014) : 2014 | REQUIREMENTS FOR ELASTOMERIC TOROIDAL SEALING RINGS ('O'-RINGS) - PART 1: GENERAL AND SURFACE FINISH STANDARDS RELATIVE TO MANUFACTURER |
| DEFSTAN 02-345/2(2013) : 2013 | REQUIREMENTS FOR FLEXIBLE RUBBER PIPE ASSEMBLIES AND BELLOWS FOR USE IN SYSTEMS FROM VACUUM TO 20 BAR |
| BS ISO 6194-4:2009 | Rotary shaft lip-type seals incorporating elastomeric sealing elements Performance test procedures |
| 14/30293861 DC : 0 | BS ISO 18766 - RUBBER, VULCANIZED OR THERMOPLASTIC - LOW TEMPERATURE TESTING - GENERAL INTRODUCTION AND GUIDE |
| I.S. EN ISO 23936-2:2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - NON-METALLIC MATERIALS IN CONTACT WITH MEDIA RELATED TO OIL AND GAS PRODUCTION - PART 2: ELASTOMERS (ISO 23936-2:2011) |
| ISO 4632-1:1982 | Rubber, vulcanized — Classification — Part 1: Description of the classification system |
| BS 903-0:2012 | Physical testing of rubber General |
| BS F 157:2006 | Properties of high tear strength silicone rubber sheet, mouldings and extrusions. Specification |
| BS ISO 17325-2:2014 | Ships and marine technology. Marine environment protection. Oil booms Strength and performance requirements |
| 10/30219184 DC : 0 | BS ISO 23936-2 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - NON-METALLIC MATERIALS IN CONTACT WITH MEDIA RELATED TO OIL AND GAS PRODUCTION - PART 2: ELASTOMERS |
| BS ISO 18899:2013 | Rubber. Guide to the calibration of test equipment |
| API SPEC 17K : 2017 | SPECIFICATION FOR BONDED FLEXIBLE PIPE |
| ISO 6194-4:2009 | Rotary shaft lip-type seals incorporating elastomeric sealing elements — Part 4: Performance test procedures |
| BS 903-3:2003 | Physical testing of rubber Acquisition and presentation of comparable single-point data |
| API SPEC 19OH : 2018 | OPENHOLE ISOLATION EQUIPMENT |
| BS EN ISO 23936-2:2011 | Petroleum, petrochemical and natural gas industries. Nonmetallic materials in contact with media related to oil and gas production Elastomers |
| BS ISO 18766:2014 | Rubber, vulcanized or thermoplastic. Low temperature testing. General introduction and guide |
| BS F 154:2006 | Properties of fluorosilicone rubber sheet, mouldings and extrusions. Specification |
| 07/30161672 DC : 0 | BS ISO 24453 - RUBBER - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA |
| API 14A : 2015 | SPECIFICATION FOR SUBSURFACE SAFETY VALVE EQUIPMENT |
| ISO 18766:2014 | Rubber, vulcanized or thermoplastic — Low temperature testing — General introduction and guide |
| ISO 18899:2013 | Rubber — Guide to the calibration of test equipment |
| EN ISO 23936-2:2011 | Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 2: Elastomers (ISO 23936-2:2011) |
| 07/30131694 DC : 0 | BS ISO 6194-4 - ROTARY-SHAFT LIP-TYPE SEALS INCORPORATING ELASTOMERIC SEALING ELEMENTS - PART 4: PERFORMANCE TEST PROCEDURES |
| ISO 24453:2008 | Rubber — Acquisition and presentation of comparable single-point data |
| ISO 23936-2:2011 | Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact with media related to oil and gas production — Part 2: Elastomers |
| API SPEC 11D1 : 2015 INC ERR 1:2019 | Packers and Bridge Plugs |
| ISO 23529:2016 | Rubber — General procedures for preparing and conditioning test pieces for physical test methods |
| ISO 18899:2013 | Rubber — Guide to the calibration of test equipment |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.