ISO 23711:2003
Withdrawn
View Superseded by
Elastomeric seals — Requirements for materials for pipe joint seals used in water and drainage applications — Thermoplastic elastomers
Hardcopy , PDF
English
11-26-2003
04-09-2025
ISO 23711:2003 specifies requirements for materials used for moulded seals made of thermoplastic elastomers (TPEs) for joints in:
- thermoplastic piping systems for non-pressure waste water discharge (intermittent flow at up to 95 °C) inside buildings;
- thermoplastic piping systems for non-pressure underground drainage and sewerage (continuous flow at up to 45 °C and intermittent flow at up to 95 °C);
- thermoplastic rainwater piping systems.
General requirements for finished joint seals are also given; any additional requirements called for by the particular application are specified in the relevant product standards taking into account that the performance of pipe joints is a function of the seal material properties, seal geometry and pipe joint design.
| Committee |
ISO/TC 45/SC 4
|
| DevelopmentNote |
Supersedes ISO/DIS 23711 (12/2003)
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy |
| BS ISO 17885:2015 | Plastics piping systems. Mechanical fittings for pressure piping systems. Specifications |
| I.S. EN ISO 22391-3:2009 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT) - PART 3: FITTINGS |
| NF EN ISO 22391-3 : 2010 | PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT) - PART 3: FITTINGS |
| ISO 17885:2015 | Plastics piping systems — Mechanical fittings for pressure piping systems — Specifications |
| EN ISO 22391-3:2009 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009) |
| 08/30170175 DC : DRAFT JULY 2008 | BS ISO 22391-3 - PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYETHYLENE OF RAISED TEMPERATURE RESISTANCE (PE-RT) - PART 3: FITTINGS |
| 12/30255878 DC : 0 | BS ISO 17885 - PLASTICS PIPING SYSTEMS - MECHANICAL FITTINGS FOR PRESSURE PIPING SYSTEMS - SPECIFICATIONS |
| DIN EN ISO 22391-3:2010-04 | Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings (ISO 22391-3:2009) |
| ISO 22391-3:2009 | Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
| BS EN ISO 22391-3:2009 | Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT) Fittings |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 2230:2002 | Rubber products — Guidelines for storage |
| ISO 1431-1:2012 | Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — Part 1: Static and dynamic strain testing |
| ISO 3302-1:2014 | Rubber — Tolerances for products — Part 1: Dimensional tolerances |
| ISO 9691:1992 | Rubber — Recommendations for the workmanship of pipe joint rings — Description and classification of imperfections |
| ISO 4661-1:1993 | Rubber, vulcanized or thermoplastic — Preparation of samples and test pieces — Part 1: Physical tests |
| ISO 3384:2005 | Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression at ambient and at elevated temperatures |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 7743:2017 | Rubber, vulcanized or thermoplastic — Determination of compression stress-strain properties |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 471:1995 | Rubber — Temperatures, humidities and times for conditioning and testing |
| ISO 48:2010 | Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and 100 IRHD) |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.