• There are no items in your cart

ISO 286-2:2010

Current
Current

The latest, up-to-date edition.

Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Published date

06-07-2010

ISO 286-2:2010 gives values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the tables given in ISO 2861. ISO 286-2 covers values for the upper limit deviations eU, hole (for holes) and eU, shaft (for shafts) and the lower limit deviations eL, hole (for holes) and eL, shaft (for shafts).

The ISO system for tolerances on linear size provides a system of tolerances and deviations suitable for features of the following types:

  1. cylinders;
  2. two parallel opposite surfaces.

For simplicity, and also because of the importance of cylindrical workpieces of circular section, only these are referred to explicitly. It should be clearly understood, however, that the tolerances and deviations given in ISO 286-2 equally apply to workpieces of other than circular sections.

DevelopmentNote
Supersedes ISO R 286 (04/2001) Supersedes NS 1554.25 (07/2004) Supersedes ISO/DIS 286-2. (06/2010)
DocumentType
Standard
Pages
52
PublisherName
International Organization for Standardization
Status
Current
Supersedes

ISO 10303-238:2007 Industrial automation systems and integration Product data representation and exchange Part 238: Application protocol: Application interpreted model for computerized numerical controllers
I.S. EN 60079-0:2012 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD))
BS ISO 6971:2002 Cranked-link drag chains of welded construction, attachments and sprockets
BS ISO 8131:1992 Hydraulic fluid power. Single rod cylinders, 16 MPa (160 bar) compact series. Tolerances
ISO 4347:2015 Leaf chains, clevises and sheaves Dimensions, measuring forces, tensile strengths and dynamic strengths
BS ISO 3031:2000 Rolling bearings. Thrust needle roller and cage assemblies, thrust washers. Boundary dimensions and tolerances
96/709826 DC : DRAFT JUL 1996 ISO/CD 6164-1 - HYDRAULIC FLUID POWER - ONE-PIECE SQUARE-FLANGE CONNECTORS - PART 1: FOUR-SCREW SQUARE-FLANGE CONNECTORS FOR USE AT PRESSURE OF 25MPA (250 BAR) TO 35 MPA (350 BAR), DN 10 TO DN 63
BS ISO 13921:2008 Aerospace. Screws, 100 degrees reduced countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa. Dimensions
05/30132502 DC : DRAFT APR 2005 ISO 4468 - GEAR HOBS - ACCURACY REQUIREMENTS
I.S. EN 847-1:2017 TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 1: MILLING TOOLS, CIRCULAR SAW BLADES
DIN ISO 1977:2014-12 CONVEYOR CHAINS, ATTACHMENTS AND SPROCKETS (ISO 1977:2006)
17/30347199 DC : 0 BS EN ISO 204 - METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
I.S. EN 10246-9:2000 NON-DESTRUCTIVE TESTING OF STEEL TUBES - PART 9: AUTOMATIC ULTRASONIC TESTING OF THE WELD SEAM OF SUBMERGED ARC WELDED STEEL TUBES FOR THE DETECTION OF LONGITUDINAL AND/OR TRANSVERSE IMPERFECTIONS
BS ISO 10285 : 2007 ROLLING BEARINGS - SLEEVE TYPE LINEAR BALL BEARINGS - BOUNDARY DIMENSIONS AND TOLERANCES
BS ISO 6981:1992 Hydraulic fluid power. Cylinders. Rod end plain eyes. Mounting dimensions
BS ISO 8132:2014 Hydraulic fluid power. Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series
BS ISO 4468:2009 Gear hobs. Accuracy requirements
08/30178810 DC : DRAFT MAY 2008 BS EN 12750 - SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
I.S. EN 10002-1:2001 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
16/30333241 DC : 0 BS ISO 20168 - RESISTANCE WELDING - LOCKING TAPERS FOR ELECTRODE HOLDERS AND ELECTRODE CAPS
02/614072 DC : DRAFT NOV 2002 EN ISO 9409-1 - MANIPULATING INDUSTRIAL ROBOTS - MECHANICAL INTERFACES - PART 1: PLATES
ISO 23748:2016 Aerospace series — O-ring grooves — Dimensions
BS ISO 3185:2008 Aerospace. Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa. Dimensions
13/30286407 DC : 0 BS ISO 10766 - HYDRAULIC FLUID POWER - CYLINDERS - HOUSING DIMENSIONS FOR RECTANGULAR-SECTION-CUT BEARING RINGS FOR PISTONS AND RODS
BS ISO 3548-2:2009 Plain bearings. Thin-walled half bearings with or without flange Measurement of wall thickness and flange thickness
BS ISO 368:2017 Spinning preparatory, spinning and doubling (twisting) machinery. Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64
13/30275387 DC : 0 BS ISO 20332 - CRANES - PROOF OF COMPETENCE OF STEEL STRUCTURES
API 674 REDLINE : 2010 POSITIVE DISPLACEMENT PUMPS - RECIPROCATING
ISO 13417:1997 Aerospace — Airframe needle track roller, stud type, single-row, sealed — Metric series
ABMA ISO 15242-3 : 2012 ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 3: RADIAL SPHERICAL AND TAPERED ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
PREN 1870-3 : DRAFT 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
BS ISO 8434-1 : 94 AMD 9583 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - 24 DEGREE COMPRESSION FITTINGS
BS EN 13236 : 2010 SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS
08/30173839 DC : 0 BS ISO 3548-2 - PLAIN BEARINGS - THIN-WALLED HALF BEARINGS WITH OR WITHOUT FLANGE - PART 2: MEASUREMENT OF WALL THICKNESS AND FLANGE THICKNESS
BS EN 61243-1 : 2005 LIVE WORKING - VOLTAGE DETECTORS - PART 1: CAPACITIVE TYPE TO BE USED FOR VOLTAGES EXCEEDING 1 KV A.C.
API 618 : 2007 RECIPROCATING COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
14/30291756 DC : 0 BS EN 1434-2 - HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
BS ISO 8116-6:1990 Textile machinery and accessories. Beams for winding Beams for ribbon weaving and ribbon knitting. Terminology and main dimensions
17/30315891 DC : 0 BS ISO 19690-2 - DISC SPRINGS - PART 2: TECHNICAL SPECIFICATIONS
DIN ISO 3601-2:2010-08 Fluid power systems - O-rings - Part 2: Housing dimensions for general applications (ISO 3601-2:2008)
BS ISO 10762:2015 Hydraulic fluid power. Mounting dimensions for cylinders, 10 MPa (100 bar) series
16/30340569 DC : 0 BS EN 847-1 - TOOLS FOR WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 1: MILLING TOOLS, CIRCULAR SAW BLADES
ISO 12215-8:2009 Small craft — Hull construction and scantlings — Part 8: Rudders
BS ISO 5856:2008 Aerospace. Screws, 100 degrees normal countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa. Dimensions
16/30323124 DC : 0 BS ISO 20054 - PLAIN BEARINGS - BEARINGS CONTAINING DISPERSED SOLID LUBRICANTS
BS EN 61241-0:2006 Electrical apparatus for use in the presence of combustible dust General requirements
04/30098195 DC : DRAFT JUL 2004 ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
00/715331 DC : 0 ISO/CD 8434-6 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 6: 60 DEGREE CONE CONNECTORS WITH OR WITHOUT O-RING
BS ISO 11001-3:2009 Agricultural wheeled tractors and implements. Three- point hitch couplers Link coupler
BS ISO 4347:2015 Leaf chains, clevises and sheaves. Dimensions, measuring forces, tensile strengths and dynamic strengths
10/30227442 DC : 0 BS EN ISO 13710 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - RECIPROCATING POSITIVE DISPLACEMENT PUMPS
BS ISO 7425-1:1988 Hydraulic fluid power. Housing for elastomer-energized, plastic-faced seals. Dimensions and tolerances Piston seal housings
NF EN ISO 286-1 : 2010 GEOMETRICAL PRODUCT SPECIFICATION (GPS) - ISO CODE SYSTEM FOR TOLERANCES OF LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS
EN 61243-1:2005/A1:2010 LIVE WORKING - VOLTAGE DETECTORS - PART 1: CAPACITIVE TYPE TO BE USED FOR VOLTAGES EXCEEDING 1 KV A.C.
05/30032019 DC : DRAFT SEP 2005 ISO 6194-1 - ROTARY SHAFT LIP TYPE SEALS INCORPORATING ELASTOMERIC SEALING ELEMENTS - PART 1: NOMINAL DIMENSIONS AND TOLERANCES
BS EN ISO 9493:2010 Geometrical product specifications (GPS). Dimensional measuring equipment: Dial test indicators (lever type). Design and metrological characteristics
PREN 847-1 : DRAFT 2016 TOOLS FOR WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 1: MILLING TOOLS, CIRCULAR SAW BLADES
PREN ISO 24234 : DRAFT 2013 DENTISTRY - DENTAL AMALGAM (ISO/DIS 24234:2013)
I.S. EN ISO 898-2:2012 MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 2: NUTS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD (ISO 898-2:2012)
ISO 2853:1993 Stainless steel threaded couplings for the food industry
03/106013 DC : DRAFT MAR 2003 ISO 22917 - SUPERABRASIVES - LIMIT DEVIATIONS AND RUN OUT TOLERANCES FOR GRINDING WHEELS WITH DIAMOND OR CUBIC BORON NITRIDE
96/716553 DC : DRAFT NOV 1996 TR 4271 AEROSPACE SERIES - O-RINGS GROOVES - DESIGN CRITERIA FOR O-RING GROOVES - BASIC CALCULATIONS
BS 328-6:1992 Drills and reamers Countersinks, 90°, with parallel shanks and solid pilots
96/709825 DC : DRAFT JUL 1996 ISO/CD 6164-2 - HYDRAULIC FLUID POWER - ONE-PIECE SQUARE-FLANGE CONNECTORS - PART 2: FOUR-SCREW SQUARE-FLANGE CONNECTORS FOR USE AT PRESSURES OF 31,5 MPA (315 BAR) TO 40 MPA (400 BAR), DN 10 TO DN 80
13/30256266 DC : 0 BS ISO 683-18 - HEAT-TREATABLE STEELS, ALLOY STEELS AND FREE-CUTTING STEELS - PART 18: BRIGHT STEEL PRODUCTS
DIN EN 16752 E : 2015 CENTRIFUGAL PUMPS - TEST PROCEDURE FOR SEAL PACKINGS
12/30235135 DC BS ISO 16399-1. Meters for irrigation water. General requirements
BS ISO 6020-3:2015 Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Compact series with bores from 250 mm to 500 mm
BS ISO 6022:2006 Hydraulic fluid power. Mounting dimensions for single rod cylinders, 25M Pa (250 bar) series
BS ISO 5145:2017 Gas cylinders. Cylinder valve outlets for gases and gas mixtures. Selection and dimensioning
BS ISO 8116-5:2008 Textile machinery and accessories. Beams for winding Sectional beams for warp knitting machines
08/30174605 DC : DRAFT SEP 2008 BS ISO 5597 - HYDRAULIC FLUID POWER - CYLINDERS - HOUSINGS FOR SINGLE-ACTING PISTON AND ROD SEALS IN RECIPROCATING APPLICATIONS - DIMENSIONS AND TOLERANCES
BS ISO 3547-5:2007 Plain bearings. Wrapped bushes Checking the outside diameter
BS QC010000(1993) : AMD 10432 HARMONIZED SYSTEM OF QUALITY ASSESSMENT FOR ELECTRONIC COMPONENTS. CONNECTORS FOR FREQUENCIES BELOW 3 MHz FOR USE WITH PRINTED BOARDS - GENERIC SPECIFICATION: GENERAL REQUIREMENTS AND GUIDE FOR THE PREPARATION OF DETAIL SPECIFICATIONS, WITH ASSESSED QUALITY
UNE-EN 1993-1-8:2013 Eurocode 3: Design of steel structures - Part 1-8: Design of joints
ISO 204:2009 Metallic materials Uniaxial creep testing in tension Method of test
08/30184169 DC : DRAFT JUNE 2008 BS EN 61243-3 - LIVE WORKING - VOLTAGE DETECTORS - PART 3: TWO-POLE LOW-VOLTAGE TYPE
CSA C22.2 No. 60079.0 : 2015 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
06/30110083 DC : 0 ISO 20332-1 - CRANES - PROOF OF COMPETENCE OF STEEL STRUCTURES - PART 1: GENERAL
ABMA ISO 13417 : 1997 AEROSPACE - AIRFRAME NEEDLE TRACK ROLLER, STUD TYPE, SINGLE-ROW, SEALED - METRIC SERIES
ABMA ISO 10285 : 2009 : R2015 ROLLING BEARINGS - SLEEVE TYPE LINEAR BALL BEARINGS - BOUNDARY DIMENSIONS AND TOLERANCES
ISO 13942:2000 Bonded abrasive products Limit deviations and run-out tolerances
DIN ISO 6022 E : 2008 HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
ISO 12281:1999 Aerospace Rivets, solid, 100 degrees normal countersunk head, in metallic material, with or without surface treatment Dimensions
PREN 3851 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - SWIVEL NUTS, STRAIGHT
ISO 368:2017 Spinning preparatory, spinning and doubling (twisting) machinery — Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64
PREN 3748 : 200P1 AEROSPACE SERIES - O-RING GROOVES - DIMENSIONS
PREN 3852 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - STRAIGHT UNIONS, WELDED, THREADED
PREN 3856 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - SWIVEL NUTS FOR THRUST WIRE
PREN 4000 : 200P2 AEROSPACE SERIES - METALLIC MATERIALS - RULES FOR THE DRAFTING AND PRESENTATION OF DIMENSIONAL STANDARDS FOR METALLIC SEMI-FINISHED PRODUCTS
I.S. EN ISO 18217:2015 SAFETY OF WOODWORKING MACHINES - EDGE-BANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015)
ISO 3230:1998 Aerospace — Rivets, solid, 100 degrees normal countersunk head with dome, metallic material, with or without surface treatment — Dimensions
ISO 8140:2009 Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Mounting dimensions of rod-end clevises
ISO 8399-2:1998 Aerospace — Accessory drives and mounting flanges (Metric series) — Part 2: Dimensions
BS EN 13001-3-1 : 2012 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF COMPETENCE OF STEEL STRUCTURE
ISO 6195:2013 Fluid power systems and components Cylinder-rod wiper-ring housings in reciprocating applications Dimensions and tolerances
ISO 606:2015 Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets
ISO 8133:2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series
ISO 15242-2:2015 Rolling bearings Measuring methods for vibration Part 2: Radial ball bearings with cylindrical bore and outside surface
ISO 3548-2:2009 Plain bearings Thin-walled half bearings with or without flange Part 2: Measurement of wall thickness and flange thickness
ISO 11001-3:2009 Agricultural wheeled tractors and implements Three-point hitch couplers Part 3: Link coupler
ONORM EN ISO 204 : 2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
UNI EN 13001-3-1 : 2013 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF COMPETENCE OF STEEL STRUCTURE
15/30320416 DC : 0 BS EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
BS ISO 22917:2016 Precision superabrasives. Limit deviations and run-out tolerances for grinding wheels with diamond or cubic boron nitride
BIS IS 10187 : 2013 HYDRAULIC FLUID POWER - FOUR-PORT DIRECTIONAL CONTROL VALVES - MOUNTING SURFACES
EN ISO 12215-8:2009/AC:2010 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 8: RUDDERS
ISO 19259:2015 Plain bearings Bearings with embedded solid lubricants
ISO 5856:2008 Aerospace Screws, 100 degrees normal countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
NF EN ISO 204 : 2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
ISO 10285:2007 Rolling bearings — Sleeve type linear ball bearings — Boundary dimensions and tolerances
I.S. EN ISO 1179-2:2013 CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ISO 228-1 THREADS WITH ELASTOMERIC OR METAL-TO-METAL SEALING - PART 2: HEAVY-DUTY (S SERIES) AND LIGHT-DUTY (L SERIES) STUD ENDS WITH ELASTOMERIC SEALING (TYPE E) (ISO 1179-2:2013)
ISO 7986:1997 Hydraulic fluid power — Sealing devices — Standard test methods to assess the performance of seals used in oil hydraulic reciprocating applications
ISO 8132:2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series
UNE-EN ISO 24234:2015 Dentistry - Dental amalgam (ISO 24234:2015)
DIN EN ISO 12947-1:2007-04 Textiles - Determination of the abrasion resistance of fabrics by the Martindale method - Part 1: Martindale abrasion testing apparatus (ISO 12947-1:1998 + Cor. 1:2002) (includes Corrigendum AC:2006)
DIN EN 1870-3:2015-02 Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
UNE-EN 1870-4:2012 Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading
BS EN 3852:2002 Aerospace series. Pipe couplings, 60°, spherical, in titanium alloy TI-P64001. Straight unions, welded, threaded
BS EN ISO 14691:2000 Petroleum and natural gas industries. Flexible couplings for mechanical power transmission. General purpose applications
BS EN ISO 4759-3:2000 Tolerances for fasteners Plain washers for bolts, screws and nuts. Product grades A and C
BS EN 10246-9:2000 Non-destructive testing of steel tubes Automatic ultrasonic testing of the weld seam of submerged arc welded steel tubes for the detection of longitudinal and/or transverse imperfections
BS EN ISO 1559:2001 Dental materials. Alloys for dental amalgam
BS EN ISO 8750:2007 Spring-type straight pins. Coiled, standard duty
DIN EN 20898-2:1994-02 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH COARSE PITCH THREAD AND SPECIFIED PROOF LOAD VALUES
UNI EN 1218-5 : 2010 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
I.S. EN ISO 8748:2007 SPRING-TYPE STRAIGHT PINS - COILED, HEAVY DUTY
EN 50243:2002 Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers
DIN ISO 22917:2017-11 PRECISION SUPERABRASIVES - LIMIT DEVIATIONS AND RUNOUT TOLERANCES FOR GRINDING WHEELS WITH DIAMOND OR CUBIC BORON NITRIDE (ISO 22917:2016)
EN 61243-3:2014/AC:2015 LIVE WORKING - VOLTAGE DETECTORS - PART 3: TWO-POLE LOW-VOLTAGE TYPE
EN 10246-9:2000 Non-destructive testing of steel tubes - Part 9: Automatic ultrasonic testing of the weld seam of submerged arc welded steel tubes for the detection of longitudinal and/or transverse imperfections
DIN ISO 8116-5:2009-08 TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 5: SECTIONAL BEAMS FOR WARP KNITTING MACHINES
EN 50109-2-4:1995 Hand crimping tools - Tools for the crimp termination of electric cables and wires for low frequency and radio frequency applications - Part 2-4: Particular requirements for centre contacts of RF connectors, series SMZ
EN ISO 14638:2015 Geometrical product specifications (GPS) - Matrix model (ISO 14638:2015)
EN 10246-3:1999 Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
EN 1218-3:2001+A1:2009 Safety of woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
EN 10319-1:2003 Metallic materials - Tensile stress relaxation testing - Part 1: Procedure for testing machines
DIN EN ISO 4064-2:2017-10 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS (ISO 4064-2:2014)
EN ISO 15848-1:2015/A1:2017 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves - Amendment 1 (ISO 15848-1:2015/Amd 1:2017)
EN 13411-6:2004+A1:2008 Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
EN 175500:1997 Sectional specification: Cable outlet accessories for connectors, including qualification approval and capability approval
DIN EN 1090-2:2011-10 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
DIN EN ISO 8750:2007-07 Spring-type straight pins - Coiled, standard duty (ISO 8750:2007)
EN 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
EN 13001-3-1:2012+A2:2018 Cranes - General Design - Part 3-1: Limit States and proof competence of steel structure
CEN/TS 13001-3-1:2004/AC:2006 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
EN 50014:1997/A2:1999 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - GENERAL REQUIREMENTS
DIN EN ISO 8434-1:2008-02 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
EN 1218-4:2004+A2:2009 Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines fed by chain(s)
DIN ISO 6022:2008-06 HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
NBR 16080 : 2013 INTERNAL COMBUSTION ENGINES - CYLINDER LINERS ASSEMBLED IN THE BLOCK WITH OR WITHOUT CONTACT WITH THE COOLANT (WET AND DRY TYPE RESPECTIVELY)
ONORM EN ISO 1179-2 : 2014 CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ISO 228-1 THREADS WITH ELASTOMERIC OR METAL-TO-METAL SEALING - PART 2: HEAVY-DUTY (S SERIES) AND LIGHT-DUTY (L SERIES) STUD ENDS WITH ELASTOMERIC SEALING (TYPE E) (ISO 1179-2:2013)
OVE/ONORM EN 61243-3 : 2015 LIVE WORKING - VOLTAGE DETECTORS - PART 3: TWO-POLE LOW-VOLTAGE TYPE (IEC 61243-3:2014 + COR.1:2015)
NBR IEC 60079-0 : 2013 ERRATA 2 2016 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
DIN ISO 13012-2:2010-02 Rolling bearings - Accessories for sleeve type linear ball bearings - Part 2: Boundary dimensions and tolerances for series 5 (ISO 13012-2:2009)
10/30165716 DC : 0 BS ISO 898-6 - MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD
ISO 20332:2016 Cranes Proof of competence of steel structures
ISO 7425-1:1988 Hydraulic fluid power Housings for elastomer-energized, plastic-faced seals Dimensions and tolerances Part 1: Piston seal housings
BS A 326:1998 Rivets, solid, 100° normal countersunk head with dome, metallic material, with or without surface treatment. Dimensions
10/30165662 DC : 0 BS ISO 13706 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AIRCOOLED HEAT EXCHANGERS
UNE-EN ISO 5821:2010 Resistance welding - Spot welding electrode caps (ISO 5821:2009)
ISO 4468:2009 Gear hobs Accuracy requirements
BS ISO 29262:2011 Production equipment for microsystems. Interface between end effector and handling system
BS ISO 13074:2012 Analogue quartz clocks. Fitting dimensions of movements to hands
ISO 4401:2005 Hydraulic fluid power — Four-port directional control valves — Mounting surfaces
EN 1218-5:2004+A1:2009 Safety of woodworking machines - Tenoning machines - Part 5: One side profiling machines with fixed table and feed rollers or feed chain
PD ISO/TS 17988:2014 Dentistry. Corrosion test methods for dental amalgam
NF ISO 14368-3 : 2008 MINERAL AND SAPPHIRE WATCH-GLASSES - PART 3: QUALITATIVE CRITERIA AND TESTS METHODS
16/30290140 DC : 0 BS EN ISO 8434-1 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREES CONE CONNECTORS
DIN ISO 3547-5:2015-12 PLAIN BEARINGS - WRAPPED BUSHES - PART 5: CHECKING THE OUTSIDE DIAMETER (ISO 3547-5:2007)
10/30234189 DC : 0 BS ISO 12488-1 - CRANES - TOLERANCES FOR WHEELS AND TRAVEL AND TRAVERSING TRACKS - PART 1: GENERAL
BS ISO 13012-1:2009 Rolling bearings. Accessories for sleeve type linear ball bearings Boundary dimensions and tolerances for series 1 and 3
API 618 : 2007 : R2016 RECIPROCATING COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
96/704404 DC : 0 ISO/DIS 9121 - GEOMETRICAL PRODUCT SPECIFICATION (GPS) - DIMENSIONAL MEASURING INSTRUMENTS - INTERNAL MICROMETERS WITH TWO-POINT CONTACT - DESIGN AND METROLOGICAL REQUIREMENTS
05/30135789 DC : DRAFT JUL 2005 EN ISO 8434-1 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREES CONE CONNECTORS
BS ISO 5291:2011 Belt drives. Grooved pulleys for joined classical V-belts. Groove sections AJ, BJ, CJ and DJ (effective system)
17/30355176 DC : 0 BS ISO 368 - SPINNING PREPARATORY, SPINNING AND DOUBLING (TWISTING) MACHINERY - TUBES FOR RING-SPINNING, DOUBLING AND TWISTING SPINDLES, TAPER 1:38 AND 1:64
BS ISO 13012:1998 Rolling bearings, linear motion, recirculating ball, sleeve type. Accessories
BS ISO 8434-6:2009 Metallic tube connections for fluid power and general use 60° cone connectors with or without O-ring
13/30274177 DC : 0 BS ISO 10762 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR CYLINDERS, 10 MPA (100 BAR) SERIES
BS ISO 14368-1:2000 Mineral and sapphire watch-glasses Dimensions and tolerances
BS A 323:1998 Bihexagonal drives. Wrenching configuration. Metric series
EN 3478 : 2001 AEROSPACE SERIES - O-RING GROOVES - DIMENSIONS
ISO 3185:2008 Aerospace Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
BS ISO 3601-2:2016 Fluid power systems. O-rings Housing dimensions for general applications
ISO 4205:2016 Countersinks, 90°, with parallel shanks and solid pilots
BS ISO 6020-2:2015 Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Compact series
09/30178652 DC : 0 BS EN ISO 6892-2 - METALLIC MATERIALS - TENSILE TESTING - PART 2: METHOD OF TEST AT ELEVATED TEMPERATURE
ISO 15242-3:2017 Rolling bearings — Measuring methods for vibration — Part 3: Radial spherical and tapered roller bearings with cylindrical bore and outside surface
14/30294680 DC : 0 BS ISO 19259 - PLAIN BEARINGS - BEARINGS WITH EMBEDDED SOLID LUBRICANT
DIN 3861 E : 2002 NON-SOLDERING COMPRESSION FITTINGS - COMPRESSION RINGS - DESIGN
ISO 10190:2008 Motorcycle chains — Characteristics and test methods
04/30096361 DC : DRAFT APR 2004 ISO/DIS 15242-3 - ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 3: RADIAL DOUBLE-ROW SPHERICAL AND TAPERED ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
06/30128838 DC : DRAFT MAR 2006 ISO 13726 - HYDRAULIC FLUID POWER - SINGLE ROD CYLINDERS, 16 MPA (160 BAR) COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM - ACCESSORY MOUNTING DIMENSIONS
07/30144373 DC : 0 BS ISO 3601-2 - FLUID POWER SYSTEMS - O-RINGS - PART 2: HOUSING DIMENSIONS FOR GENERAL APPLICATIONS
DD CEN/TS 13001-3-1 : 2004 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
BS ISO 20168:2016 Resistance welding. Locking tapers for electrode holders and electrode caps
BS ISO 14368-3:2003 Mineral and sapphire watch-glasses Qualitative criteria and test methods
BS ISO 22037:2007 Solid end mills with corner radii and cylindrical shanks made of hard cutting materials. Dimensions
04/30116417 DC : DRAFT JUL 2004 ISO 8133 - HYDRAULIC FLUID POWER - SINGLE ROD CYLINDERS, 16 MPA (160 BAR) COMPACT SERIES - ACCESSORY MOUNTING DIMENSIONS
15/30314221 DC : 0 BS ISO 22917 - SUPERABRASIVES - LIMIT DEVIATIONS AND RUN-OUT TOLERANCES FOR GRINDING WHEELS WITH DIAMOND OR CUBIC BORON NITRIDE
BS 341-3:2002 Transportable gas container valves Valve outlet connections
DIN ISO 8116-2 E : 2009 TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 2: WARPER'S BEAMS
05/30127444 DC : DRAFT JAN 2005 ISO 10303-238 - INDUSTRIAL AUTOMATION SYSTEMS AND INTEGRATION - PRODUCT DATA REPRESENTATION AND EXCHANGE - PART 238: APPLICATION PROTOCOL - APPLICATION INTERPRETED MODEL FOR COMPUTERIZED NUMERIC CONTROLLERS
PREN 1090-2 : DRAFT 2015 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
BS QC 480000(1995) : 1995 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH SPEED DATA APPLICATIONS - PART 1: GENERIC SPECIFICATION
04/30126679 DC : DRAFT DEC 2004 BS ISO 3245 - ROLLING BEARINGS - NEEDLE ROLLER BEARINGS, DRAWN CUP WITHOUT INNER RINGS - BOUNDARY DIMENSIONS AND TOLERANCES
08/30184322 DC : DRAFT JUNE 2008 BS ISO 8140 - PNEUMATIC FLUID POWER - CYLINDERS, 1000 KPA (10 BAR) SERIES - MOUNTING DIMENSIONS OF ROD END CLEVIS
BS ISO 3019-2:2001 Hydraulic fluid power. Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Metric series
BS ISO 1275:2006 Double-pitch precision roller chains, attachments and associated chain sprockets for transmission and conveyors
BS A 311:1997 Aerospace. Screws, 100° reduced countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa. Dimensions
BS EN 175500:1997 Harmonized system of quality assessment for electronic components. Sectional specification:cable outlet accessories for connectors, including qualification approval and capability approval
API 673 : 2014 CENTRIFUGAL FANS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
SAE J 2122 : 1998 NUMBERING SYSTEM FOR SINGLE DIAMETER DRILLS
UNE-EN 1090-2:2011 Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures
ISO 529:2017 Short machine taps and hand taps
PREN 3264 : 200P3 AEROSPACE SERIES - PIPE COUPLING 8 DEGREES 30 MINUTES IN TITANIUM ALLOY - THRUST WIRE NUTS
XP PREN 3851 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - SWIVEL NUTS, STRAIGHT
ISO 6526:2017 Plain bearings — Pressed bimetallic half thrust washers — Features and tolerances
API 611 : 2008 GENERAL-PURPOSE STEAM TURBINES FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
DIN EN ISO 18217 E : 2015 SAFETY OF WOODWORKING MACHINES - EDGEBANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015)
ISO 6022:2006 Hydraulic fluid power — Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series
TR 4271 : 1 AEROSPACE SERIES - O-RINGS GROOVES - DESIGN CRITERIA FOR O-RING GROOVES - BASIC CALCULATIONS
I.S. EN ISO 204:2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
UNE-EN ISO 286-1:2011 Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits (ISO 286-1:2010)
BS EN 61243-3:2014 Live working. Voltage detectors Two-pole low-voltage type
API 674 : 2010 POSITIVE DISPLACEMENT PUMPS - RECIPROCATING
API 674 : 2010 : ERR 1 : 2014 POSITIVE DISPLACEMENT PUMPS - RECIPROCATING
UNE-EN 16752:2015 Centrifugal pumps - Test procedure for seal packings
BIS IS 15469 : 2012 AEROSPACE - BOLTS, NORMAL BIHEXAGONAL HEAD, NORMAL SHANK, SHORT OR MEDIUM LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES LESS THAN OR EQUAL TO 1100 MPA - DIMENSIONS
BS EN 60079-0 : 2012 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
I.S. CEN TS 13001-3-1:2005 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
OIML R 49-2 : 2013 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS
EN 1434-2:2015 Heat meters - Part 2: Constructional requirements
ISO 9254:1993 Aerospace Bolt, normal spline head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
I.S. EN 50243:2002 OUTDOOR BUSHINGS FOR 24 KV AND 36 KV AND FOR 5 KA AND 8 KA, FOR LIQUID FILLED TRANSFORMERS
BS ISO 8133:2014 Hydraulic fluid power. Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series
ABMA ISO 15242-4 : 2012 ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 4: RADIAL CYLINDRICAL ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
BIS IS 12673-1 : 2014 TEXTILES - DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD - PART 1: MARTINDALE ABRASION TESTING APPARATUS
CEI EN 60603-1 : 2001 CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 1: GENERIC SPECIFICATION; GENERAL REQUIREMENTS AND GUIDE FOR THE PREPARATION OF DETAIL SPECIFICATIONS, WITH ASSESSED QUALITY
DIN EN ISO 8434-1:2016-10 (Draft) METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
DIN EN 1090-2:2015-07 (Draft) EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
UNI EN 1090-2 : 2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
NF EN 61243-1 : 2005 AMD 1 2010 LIVE WORKING - VOLTAGE DETECTORS - PART 1: CAPACITIVE TYPE TO BE USED FOR VOLTAGES EXCEEDING 1 KV A.C.
BS EN ISO 8434-1:2007 Metallic tube connections for fluid power and general use 24 degree cone connectors
ISO/TR 18569:2004 Safety of machinery Guidelines for the understanding and use of safety of machinery standards
UNE-EN 1434-2:2016 Heat meters - Part 2: Constructional requirements
ISO 10303-223:2008 Industrial automation systems and integration — Product data representation and exchange — Part 223: Application protocol: Exchange of design and manufacturing product information for cast parts
ISO 783:1999 Metallic materials Tensile testing at elevated temperature
DIN EN 10319-2:2007-01 Metallic materials - Tensile stress relaxation testing - Part 2: Procedure for bolted joint models
DIN EN 13411-6 E : 2009 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET
DIN EN 1011-6:2006-03 WELDING - RECOMMENDATION FOR WELDING OF METALLIC MATERIALS - PART 6: LASER BEAM WELDING
DIN EN 1870-8:2013-03 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
DIN EN 1993-1-8:2010-12 Eurocode 3: Design of steel structures - Part 1-8: Design of joints (includes Corrigendum AC:2009)
DIN ISO 15242-1:2014-06 ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 1: FUNDAMENTALS (ISO 15242-1:2004)
BS EN ISO 9409-1:2004 Manipulating industrial robots. Mechanical interfaces Plates
BS EN 10246-3:2000 Non-destructive testing of steel tubes Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections
BS EN ISO 9974-1:2000 Connections for general use and fluid power. Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Threaded ports
BS EN 3855:2002 Aerospace series. Pipe couplings, 60° spherical, in titanium alloy TI-P64001. Caps
ISO 15848-1:2015 Industrial valves Measurement, test and qualification procedures for fugitive emissions Part 1: Classification system and qualification procedures for type testing of valves
ISO 15242-1:2015 Rolling bearings Measuring methods for vibration Part 1: Fundamentals
BS EN ISO 15912:2016 Dentistry. Refractory investment and die material
09/30206527 DC : 0 BS EN 60079-0 ED 6.0 - EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
BIS IS/IEC 60079-0 : 2011 EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS
I.S. EN 1870-8:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
DIN EN 1218-4:2009-12 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 4: EDGE BANDING MACHINES FED BY CHAIN(S)
DIN EN 10002-1:2001-12 METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE
I.S. EN ISO 8751:2007 SPRING-TYPE STRAIGHT PINS - COILED, LIGHT DUTY
I.S. EN ISO 4759-3:2016 TOLERANCES FOR FASTENERS - PART 3: WASHERS FOR BOLTS, SCREWS AND NUTS - PRODUCT GRADES A, C AND F (ISO 4759-3:2016)
I.S. EN ISO 15912:2016 DENTISTRY - REFRACTORY INVESTMENT AND DIE MATERIAL (ISO 15912:2016)
I.S. EN ISO 8750:2007 SPRING-TYPE STRAIGHT PINS - COILED, STANDARD DUTY
I.S. EN 1218-2:2004 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 2: DOUBLE END TENONING AND/OR PROFILING MACHINES FED BY CHAIN OR CHAINS
DIN EN 1218-3:2009-12 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
I.S. EN 1870-3:2014 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
I.S. EN 12750:2013 SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
I.S. EN 1218-3:2002 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
I.S. EN 1218-5:2004 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
I.S. EN 13411-6:2004 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET
I.S. EN 3867:2005 AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGES IN TITANIUM ALLOY TI-P64001
I.S. EN ISO 1559:2002 DENTAL MATERIALS - ALLOYS FOR DENTAL AMALGAM
I.S. EN 3868:2005 AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGE CONNECTORS, WELDED, IN TITANIUM ALLOY TI-P64001
I.S. EN ISO 9409-1:2004 MANIPULATING INDUSTRIAL ROBOTS - MECHANICAL INTERFACES - PART 1: PLATES
I.S. EN ISO 24234:2015 DENTISTRY - DENTAL AMALGAM (ISO 24234:2015)
DIN EN ISO 24234:2015-08 DENTISTRY - DENTAL AMALGAM (ISO 24234:2015)
I.S. EN ISO 10441:2007 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLEXIBLE COUPLINGS FOR MECHANICAL POWER TRANSMISSION - SPECIAL-PURPOSE APPLICATIONS
I.S. EN ISO 15848-1:2015 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015)
DIN EN ISO 9409-1:1997-06 MANIPULATING INDUSTRIAL ROBOTS - MECHANICAL INTERACES - PART 1: PLATES
ISA 61241-0 : 2006 ELECTRICAL APPARATUS FOR USE IN ZONE 20, ZONE 21 AND ZONE 22 HAZARDOUS (CLASSIFIED) LOCATIONS - GENERAL REQUIREMENTS
I.S. EN 1870-4:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
DIN EN ISO 9409-2:2003-10 MANIPULATING INDUSTRIAL ROBOTS - MECHANICAL INTERFACES - PART 2: SHAFTS
OVE/ONORM EN 61243-1 : 2010 LIVE WORKING - VOLTAGE DETECTORS - PART 1: CAPACITIVE TYPE TO BE USED FOR VOLTAGES EXCEEDING 1 KV A.C.
BS 1916-3:2009 Limits and fits for engineering Guide to tolerances, limits and fits for large diameters
VDI/VDE/DGQ 2618 Blatt 10.7:2010-08 Inspection of measuring and test equipment - Test instruction for internal micrometers with 2-point contact
VDI/VDE/DGQ 2618 Blatt 4.4:2009-09 Inspection of measuring and test equipment - Test instruction for reference gauges with plane-parallel or spherical measuring faces and for spherical-end gauges and internal callipers
ISO 10500:1991 Industrial tyres and rims — Cylindrical and conical base rubber solid tyres (metric series) — Designation, dimensions and marking
API 671 : 2007 SPECIAL PURPOSE COUPLINGS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
05/30070377 DC : DRAFT OCT 2005 ISO 10441 - PETROLEUM AND NATURAL GAS INDUSTRIES - FLEXIBLE COUPLINGS FOR MECHANICAL POWER TRANSMISSION - SPECIAL PURPOSE APPLICATIONS
17/30348149 DC : 0 BS ISO 3096 - ROLLING BEARINGS - NEEDLE ROLLERS - BOUNDARY DIMENSIONS, GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) AND TOLERANCE VALUES
I.S. EN ISO 8434-1:2007 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
ISO 5049-1:1994 Mobile equipment for continuous handling of bulk materials Part 1: Rules for the design of steel structures
ISO 7299-2:2009 Diesel engines End-mounting flanges for pumps Part 2: High-pressure supply pumps for common rail fuel injection systems
DIN ISO 29262:2013-03 Production equipment for microsystems - Interface between end effector and handling system (ISO 29262:2011)
17/30359782 DC : 0 BS ISO 8140 - PNEUMATIC FLUID POWER - CYLINDERS, 1000 KPA (10 BAR) SERIES - MOUNTING DIMENSIONS OF ROD-END CLEVISES
14/30304022 DC : 0 BS ISO 7368 - HYDRAULIC FLUID POWER - TWO-PORT SLIP-IN CARTRIDGE VALVES - CAVITIES
I.S. EN 848-1:2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
BS ISO 20054:2016 Plain bearings. Bearings containing dispersed solid lubricants
DIN EN ISO 18217:2015-12 Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
BS 4500-1.1(1990) : AMD 7630 ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - SPECIFICATION FOR BASES OF TOLERANCES, DEVIATIONS AND FITS
98/715115 DC : DRAFT SEP 1998 ISO/CD 6982 - HYDRAULIC FLUID POWER - CYLINDERS - ROD END SPHERICAL EYES - MOUNTING DIMENSIONS
BS EN ISO 4064-2:2017 Water meters for cold potable water and hot water Test methods
BS ISO 10898:2016 Spot drills
UNI ISO 3408-3 : 2009 BALL SCREWS - PART 3: ACCEPTANCE CONDITIONS AND ACCEPTANCE TESTS
03/103749 DC : DRAFT FEB 2003 BS ISO 12488-1 - CRANES - TOLERANCES FOR WHEELS AND TRAVEL AND TRAVERSING TRACKS - PART 1: GENERAL
I.S. EN ISO 898-6:1996 MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD
16/30342178 DC : 0 BS ISO 15242-3 - ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 3: RADIAL SPHERICAL AND TAPERED ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
BS ISO 529:2017 Short machine taps and hand taps
IEEE 810-2015 IEEE Standard for Hydraulic Turbine and Generator Shaft Couplings and Shaft Runout Tolerances
11/30248447 DC : 0 BS EN 847-1 - TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 1: MILLING TOOLS, CIRCULAR SAW BLADES
05/30128677 DC : DRAFT FEB 2005 ISO 3193 - AEROSPACE - BOLTS, NORMAL HEXAGONAL HEAD, NORMAL SHANK, SHORT OR MEDIUM-LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES LESS THAN OR EQUAL TO 1100 MPA - DIMENSIONS
10/30232428 DC : DRAFT DEC 2010 BS EN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING
14/30280974 DC : 0 BS EN ISO 4759-3 - TOLERANCES FOR FASTENERS - PART 3: WASHERS FOR BOLTS, SCREWS AND NUTS - PRODUCT GRADES A, C AND F
BS ISO 9766:2012 Drills with indexable inserts. Cylindrical shanks with a parallel flat
BS ISO 10766:2014 Hydraulic fluid power. Cylinders. Housing dimensions for rectangular-section-cut bearing rings for pistons and rods
BS ISO 7902-3:1998 Hydrodynamic plain journal bearings under steady-state conditions. Circular cylindrical bearings Permissible operational parameters
07/30148058 DC : 0 BS ISO 8116-3 - TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 3: WEAVER'S BEAMS
BS ISO 7299-2:2009 Diesel engines. End-mounting flanges for pumps High-pressure supply pumps for common rail fuel injection systems
UNI CEI EN ISO 4064-2 : 2014 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS
96/716552 DC : DRAFT NOV 1996 PREN 3748 AEROSPACE SERIES - O-RINGS GROOVES - DIMENSIONS
03/309159 DC : DRAFT MAY 2003 EN 847-1 - TOOLS FOR WOODWORKING - SAFETY REQUIREMENTS - PART 1: MILLING TOOLS, CIRCULAR SAW BLADES
04/30077768 DC : DRAFT FEB 2004 ISO 4401 - HYDRAULIC FLUID POWER - FOUR-PORT DIRECTIONAL CONTROL VALVES - MOUNTING SURFACES
BS ISO 3186:2008 Aerospace. Bolts, large bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes 1250 MPa to 1800 MPa. Dimensions
10/30168898 DC : 0 BS EN ISO 24234/A1 - REQUIREMENTS FOR MARKING AND MANUFACTURER'S INSTRUCTIONS CONCERNING MERCURY
BS ISO 1977:2006 Conveyor chains, attachments and sprockets
DIN EN ISO 4064-2:2016-09 (Draft) WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS (ISO 4064-2:2014)
DIN ISO 15242-2:2014-06 ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 2: RADIAL BALL BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE (ISO 15242-2:2004 + COR. 1:2010)
BS A 361:2000 Rivets, solid, 100° normal countersunk head, in metallic material, with or without surface treatment. Dimensions
DIN EN ISO 14638 E : 2015 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MATRIX MODEL (ISO 14638:2015)
DIN EN ISO 1179-2:2014-03 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)
BS ISO 7425-2:1989 Hydraulic fluid power. Housing for elastomer-energized, plastic-faced seals. Dimensions and tolerances Rod seal housings
05/30128686 DC : DRAFT FEB 2005 ISO 13921 - AEROSPACE - SCREWS, 100 DEGREES REDUCED COUNTERSUNK HEAD, INTERNAL OFFSET CRUCIFORM RIBBED OR UNRIBBED DRIVE, NORMAL SHANK, SHORT OR MEDIUM-LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES LESS THAN OR EQUAL TO 1100 MPA - DIMENSION
12/30242874 DC : 0 BS ISO 1206:2001/AMD 1 - ROLLING BEARINGS - NEEDLE ROLLER BEARINGS, DIMENSION SERIES 48, 49 AND 69 - BOUNDARY DIMENSIONS AND TOLERANCES
XP PREN 3853 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - STRAIGHT UNIONS, THREADED
XP PREN 3852 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - STRAIGHT UNIONS, WELDED, THREADED
NF EN 1993 1-8 : 2005 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS
BS ISO 10303-47:1997 Industrial automation systems and integration. Product data representation and exchange Integrated generic resource. Shape variation tolerances
BS EN ISO 1179-2:2013 Connections for general use and fluid power. Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
XP PREN 3868 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGE CONNECTORS, WELDED, IN TITANIUM ALLOY TI-P64001
09/30192800 DC : 0 BS ISO 29262 - PRODUCTION EQUIPMENT FOR MICROSYSTEMS - INTERFACE BETWEEN GRIPPERS AND HANDLING SYSTEM
XP PREN 3867 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGES IN TITANIUM ALLOY TI-P64001
XP PREN 3856 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - SWIVEL NUTS FOR THRUST WIRE
ISO 3408-3:2006 Ball screws Part 3: Acceptance conditions and acceptance tests
BS ISO 15242-4:2017 Rolling bearings. Measuring methods for vibration Radial cylindrical roller bearings with cylindrical bore and outside surface
UNI CEN/TS 13001-3-1 : 2005 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
DIN ISO 3547-5:2015-12 PLAIN BEARINGS - WRAPPED BUSHES - PART 5: CHECKING THE OUTSIDE DIAMETER (ISO 3547-5:2007)
10/30194324 DC : 0 BS ISO 3030 - ROLLING BEARINGS - RADIAL NEEDLE ROLLER AND CAGE ASSEMBLIES - BOUNDARY DIMENSIONS AND TOLERANCES
UNI ISO 8434-6 : 2012 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 6: 60 DEGREE CONE CONNECTORS WITH OR WITHOUT O-RING
BS ISO 6982:1992 Hydraulic fluid power. Cylinders. Rod end spherical eyes. Mounting dimensions
BS EN 50243:2002 Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers
BS ISO 5290:2001 Belt drives. Grooved pulleys for narrow V-belts. Groove sections 9N/J, 15N/J and 25N/J (effective system)
08/30181655 DC : DRAFT SEP 2008 BS EN 13001-3-1 - CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF OF COMPETENCE OF STEEL STRUCTURES
08/30189270 DC : 0 BS EN 13236 - SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS
UNI EN ISO 286-1 : 2010 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS
12/30235512 DC : 0 BS ISO 5145 - CYLINDER VALVE OUTLETS FOR GASES AND GAS MIXTURES - SELECTION AND DIMENSIONING
05/30128695 DC : DRAFT FEB 2005 ISO 9255 - AEROSPACE - BOLTS, NORMAL SPLINE HEAD, NORMAL SHANK, SHORT OR MEDIUM-LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES LESS THAN OR EQUAL TO 1100 MPA - DIMENSIONS
BS EN ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel Nuts with specified property classes. Coarse thread and fine pitch thread
BS EN 50014:1998 Electrical apparatus for potentially explosive atmospheres. General requirements
03/115225 DC : DRAFT SEP 2003 BS EN 1011-6 - WELDING - RECOMMENDATION FOR WELDING OF METALLIC MATERIALS - PART 6: LASER BEAM WELDING
03/116547 DC : DRAFT NOV 2003 EN ISO 15848-1 - INDUSTRIAL VALVES - FUGITIVE EMISSIONS - MEASUREMENT TEST AND QUALIFICATION PROCEDURES - PART 1: CLASSIFICATION SYSTEM AND QUALIFICATION PROCEDURES FOR TYPE TEST OF VALVE ASSEMBLIES
ABMA ISO 10285 : 2009 ROLLING BEARINGS - SLEEVE TYPE LINEAR BALL BEARINGS - BOUNDARY DIMENSIONS AND TOLERANCES
ISO 7902-3:1998 Hydrodynamic plain journal bearings under steady-state conditions Circular cylindrical bearings Part 3: Permissible operational parameters
BS ISO 7368:2016 Hydraulic fluid power. Two-port slip-in cartridge valves. Cavities
API 611 : 2008 : R2014 GENERAL-PURPOSE STEAM TURBINES FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
API 672 : 2004 PACKAGED, INTEGRALLY GEARED CENTRIFUGAL AIR COMPRESSORS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
API 674 : 2010 : INC : ERR 1 : 2015 : R2016 POSITIVE DISPLACEMENT PUMPS - RECIPROCATING
BS ISO 13012-2:2009 Rolling bearings. Accessories for sleeve type linear ball bearings Boundary dimensions and tolerances for series 5
CEI EN 61076-1 : 2007 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
BS ISO 1206 : 2001 ROLLING BEARINGS - NEEDLE ROLLER BEARINGS, DIMENSION SERIES 48, 49 AND 69 -BOUNDARY DIMENSIONS AND TOLERANCES
API STD 541 : 2014 FORM-WOUND SQUIRREL CAGE INDUCTION MOTORS - 375 KW (500 HORSEPOWER) AND LARGER
ISO 22917:2016 Precision superabrasives Limit deviations and run-out tolerances for grinding wheels with diamond or cubic boron nitride
ISO 3096:1996 Rolling bearings Needle rollers Dimensions and tolerances
CSA E60079.0 : 2002 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - GENERAL REQUIREMENTS
I.S. EN ISO 5821:2009 RESISTANCE WELDING - SPOT WELDING ELECTRODE CAPS
UNI EN ISO 12215-8 : 2009 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 8: RUDDERS
ISO 13012-2:2009 Rolling bearings Accessories for sleeve type linear ball bearings Part 2: Boundary dimensions and tolerances for series 5
I.S. EN 10319-2:2006 METALLIC MATERIALS - TENSILE STRESS RELAXATION TESTING - PART 2: PROCEDURE FOR BOLTED JOINT MODELS
ISO 9256:1993 Aerospace Bolts, large hexagonal head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
ISO/TR 17671-6:2005 Welding Recommendations for welding of metallic materials Part 6: Laser beam welding
ISO 7425-2:1989 Hydraulic fluid power Housings for elastomer-energized, plastic-faced seals Dimensions and tolerances Part 2: Rod seal housings
ISO 3203:1993 Aerospace — Bolts, normal bihexagonal head, normal or pitch diameter shank, long length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions
ISO 683-18:2014 Heat-treatable steels, alloy steels and free-cutting steels — Part 18: Bright steel products
ISO 3186:2008 Aerospace — Bolts, large bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes 1 250 MPa to 1 800 MPa — Dimensions
ISO 3193:2008 Aerospace Bolts, normal hexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
DIN ISO 15242-3:2014-06 ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 3: RADIAL SPHERICAL AND TAPERED ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE (ISO 15242-3:2006 + COR. 1:2010)
BS ISO 3096:1996 Rolling bearings. Needle rollers. Dimensions and tolerances
UNE-EN ISO 898-2:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread (ISO 898-2:2012)
UNE-EN ISO 9493:2012 Geometrical product specifications (GPS) - Dimensional measuring equipment: Dial test indicators (lever type) - Design and metrological characteristics (ISO 9493:2010)
UNI EN ISO 8434-1 : 2007 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
DIN EN 1434-2:2016-02 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
ISO 12307-1:1994 Plain bearings — Wrapped bushes — Part 1: Checking the outside diameter
ISO 2795:2014 Plain bearings Sintered bushes Dimensions and tolerances
BIS IS/ISO 6194-1 : 2007 ROTARY SHAFT LIP-TYPE SEALS INCORPORATING ELASTOMERIC SEALING ELEMENTS - PART 1: NOMINAL DIMENSIONS AND TOLERANCES
EN 1090-2:2008+A1:2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
EN ISO 8434-1:2007/AC:2009 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
BS EN ISO 12215-8:2009 Small craft. Hull construction and scantlings Rudders
ISO 5597:2010 Hydraulic fluid power Cylinders Dimensions and tolerances of housings for single-acting piston and rod seals in reciprocating applications
ISO 6020-3:2015 Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 3: Compact series with bores from 250 mm to 500 mm
DIN EN ISO 12215-8:2009-10 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 8: RUDDERS
ISO 1103:2007 Road vehicles — Coupling balls for caravans and light trailers — Dimensions
ISO 15242-4:2017 Rolling bearings — Measuring methods for vibration — Part 4: Radial cylindrical roller bearings with cylindrical bore and outside surface
ISO 10303-219:2007 Industrial automation systems and integration — Product data representation and exchange — Part 219: Application protocol: Dimensional inspection information exchange
ISO 10766:2014 Hydraulic fluid power Cylinders Housing dimensions for rectangular-section-cut bearing rings for pistons and rods
ISO 7368:2016 Hydraulic fluid power — Two-port slip-in cartridge valves — Cavities
ISO 8434-6:2009 Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors with or without O-ring
ISO 14368-3:2003 Mineral and sapphire watch-glasses Part 3: Qualitative criteria and test methods
BS EN 1090-2 : 2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
ISO 6972:2002 Cranked-link mill chains of welded construction, attachments and sprockets
ISO 10303-214:2010 Industrial automation systems and integration Product data representation and exchange Part 214: Application protocol: Core data for automotive mechanical design processes
IEC 61241-0:2004 Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
ISO 8139:2009 Pneumatic fluid power Cylinders, 1 000 kPa (10 bar) series Mounting dimensions of rod-end spherical eyes
ISO 6020-2:2015 Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series
IEC 61243-1:2003+AMD1:2009 CSV Live working - Voltage detectors - Part 1: Capacitive type to be used for voltages exceeding 1 kV a.c.
I.S. CWA 14249:2003 REVISED FUNSTEP APPLICATION REFERENCE MODEL
ISO 6971:2002 Cranked-link drag chains of welded construction, attachments and sprockets
ISO 14856:2001 Timekeeping instruments — Wristwatch-cases — Fixing dimensions of non-spring-bar types
DIN EN 12750:2013-05 Safety of woodworking machines - Four sided moulding machines
DIN EN ISO 15848-1:2015-11 INDUSTRIAL VALVES - MEASUREMENT, TEST AND QUALIFICATION PROCEDURES FOR FUGITIVE EMISSIONS - PART 1: CLASSIFICATION SYSTEM AND QUALIFICATION PROCEDURES FOR TYPE TESTING OF VALVES (ISO 15848-1:2015 + AMD.1:2017)
DIN EN 848-1:2013-01 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
DIN EN ISO 15912:2016-08 DENTISTRY - REFRACTORY INVESTMENT AND DIE MATERIAL (ISO 15912:2016)
DIN EN ISO 8751 E : 2007 SPRING-TYPE STRAIGHT PINS - COILED, LIGHT DUTY
BS EN 848-1 : 2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
ISO 8748:2007 Spring-type straight pins Coiled, heavy duty
BS EN 3851:2003 Aerospace series. Pipe couplings, 60°, spherical, in titanium alloy TI-P64001. Swivel nuts, straight
BS EN ISO 9974-3:2000 Connections for general use and fluid power. Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Stud ends with metal-to-metal sealing (type B)
BS EN 1218-2 : 2004 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 2: DOUBLE END TENONING AND/OR PROFILING MACHINES FED BY CHAIN OR CHAINS
BS EN 10319-1:2003 Metallic materials. Tensile stress relaxation testing Procedure for testing machines
UNE-EN ISO 15912:2016 Dentistry - Refractory investment and die material (ISO 15912:2016)
BS EN 13411-6 : 2004 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET
UNE-EN 848-1:2008 Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines
EN 1011-6:2005 Welding - Recommendation for welding of metallic materials - Part 6: Laser beam welding
ONORM EN 1090-2 : 2012 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
BIS IS 1608 : 2005 METALLIC MATERIALS - TENSILE TESTING AT AMBIENT TEMPERATURE
EN ISO 4759-1 : 2000 TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C
EN ISO 8748:2007 Spring-type straight pins - Coiled, heavy duty (ISO 8748:2007)
EN ISO 9409-2:2003 Manipulating industrial robots - Mechanical interfaces - Part 2: Shafts (ISO 9409-2:2002)
EN ISO 9409-1:2004 Manipulating industrial robots - Mechanical interfaces - Part 1: Plates (ISO 9409-1:2004)
EN 3855:2002 Aerospace series - Pipe couplings, 60°, spherical in titanium alloy TI-P64001 - Caps
UNI EN 1870-8 : 2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
UNI EN 12750 : 2013 SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
UNI EN 13236 : 2011 SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS
UNI EN 1218-4 : 2009 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 4: EDGE BANDING MACHINES FED BY CHAIN(S)
UNI EN 848-1 : 2013 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
UNI EN 20286-1 : 1995 ISO SYSTEM OF LIMITS AND FITS - BASES OF TOLERANCES, DEVIATIONS AND FITS
UNI EN 1870-4 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
UNI EN ISO 14691 : 2009 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLEXIBLE COUPLINGS FOR MECHANICAL POWER TRANSMISSION - GENERAL-PURPOSE APPLICATIONS
UNI EN 1993-1-8 : 2005 EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS
UNI EN 13411-6 : 2009 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET
UNI EN ISO 12947-1 : 2000 TEXTILES - DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD - MARTINDALE ABRASION TESTING APPARATUS
UNI EN 1218-3 : 2009 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
BS ISO 6972:2002 Cranked-link mill chains of welded construction, attachments and sprockets
ISO 8280:1993 Aerospace Rivets, solid, universal head, metallic material, with or without surface treatment Dimensions
13/30274171 DC : 0 BS ISO 8132 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR ACCESSORIES FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) MEDIUM AND 25 MPA (250 BAR) SERIES
ISO/TS 3669-2:2007 Vacuum technology Bakable flanges Part 2: Dimensions of knife-edge flanges
DIN ISO 3408-3:2011-04 Ball screws - Part 3: Acceptance conditions and acceptance tests (ISO 3408-3:2006)
DIN ISO 8116-3 E : 2009 TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 3: WEAVER'S BEAMS
DIN EN 16752:2015-11 Centrifugal pumps - Test procedure for seal packings; German version EN 16752:2015
DIN ISO 29262 E : 2013 PRODUCTION EQUIPMENT FOR MICROSYSTEMS - INTERFACE BETWEEN END EFFECTOR AND HANDLING SYSTEM (ISO 29262:2011)
BS ISO 15917:2012 Solid ball-nosed end mills with cylindrical shanks, made of carbide and ceramic materials
ISO 13921:2008 Aerospace — Screws, 100 degrees reduced countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions
NF ISO 6194-1 : 2011 ROTARY SHAFT LIP-TYPE SEALS INCORPORATING ELASTOMERIC SEALING ELEMENTS - PART 1: NOMINAL DIMENSIONS AND TOLERANCES
16/30341970 DC : 0 BS ISO 1206 - ROLLING BEARINGS - NEEDLE ROLLER BEARINGS WITH MACHINED RINGS - BOUNDARY DIMENSIONS, GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) AND TOLERANCE VALUES
16/30342175 DC : 0 BS ISO 15242-4 - ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 4: RADIAL CYLINDRICAL ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
PREN 13236 : DRAFT 2017 SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS
14/30279051 DC : 0 BS EN ISO 15848-1 - INDUSTRIAL VALVES - MEASUREMENT, TEST AND QUALIFICATION PROCEDURES FOR FUGITIVE EMISSIONS - PART 1: CLASSIFICATION SYSTEM AND QUALIFICATION PROCEDURES FOR TYPE TESTING OF VALVES
03/301350 DC : DRAFT JAN 2003 ISO 5744 - PLIERS AND NIPPERS - METHODS OF TEST
BS EN ISO 286-1:2010 Geometrical product specifications (GPS). ISO code system for tolerances on linear sizes Basis of tolerances, deviations and fits
ISO 9255:2008 Aerospace Bolts, normal spline head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
NF ENV 1993-2 : 2000 XP EUROCODE 3: DESIGN OF STEEL STRUCTURES AND NATIONAL APPLICATION DOCUMENT - PART 2: STEEL BRIDGES
14/30274168 DC : 0 BS ISO 6020-3 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 3: COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM
14/30278586 DC : 0 BS ISO 606 - SHORT-PITCH TRANSMISSION PRECISION ROLLER AND BUSH CHAINS, ATTACHMENTS AND ASSOCIATED CHAIN SPROCKETS
ISO 10762:2015 Hydraulic fluid power Mounting dimensions for cylinders, 10 MPa (100 bar) series
ISO 14368-2:2003 Mineral and sapphire watch-glasses — Part 2: Assembly to the case by adhesive or using a gasket
I.S. EN 10246-3:2000 NON-DESTRUCTIVE TESTING OF STEEL TUBES - PART 3: AUTOMATIC EDDY CURRENT TESTING OF SEAMLESS AND WELDED (EXCEPT SUBMERGED ARC-WELDED) STEEL TUBES FOR THE DETECTION OF IMPERFECTIONS
BS ISO 5597:2010 Hydraulic fluid power. Cylinders. Dimensions and tolerances of housings for single-acting piston and rod seals in reciprocating applications
DIN EN 50014 : 2000 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - GENERAL REQUIREMENTS
06/30145636 DC : DRAFT JULY 2006 ISO 3547-5 - PLAIN BEARINGS - WRAPPED BUSHES - PART 5: CHECKING THE OUTSIDE DIAMETER
13/30267665 DC : 0 BS EN ISO 24234 - DENTISTRY - DENTAL AMALGAM
BIS IS 800 : 2007 AMD 1 2012 GENERAL CONSTRUCTION IN STEEL - CODE OF PRACTICE
BS 4500-4:1985 ISO limits and fits Specification for system of cone (taper) fits for cones from <i>C</i>=1:3 to 1:500, lengths from 6 mm to 630 mm and diameters up to 500 mm
CSA C900.2 : 2013 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
14/30257552 DC : 0 BS ISO 3245 - ROLLING BEARINGS - NEEDLE ROLLER BEARINGS, DRAWN CUP WITHOUT INNER RING - GEOMETRICAL PRODUCT SPECIFICATIONS (GPS), BOUNDARY DIMENSIONS AND TOLERANCES
BS ISO 1103:2007 Road vehicles. Coupling balls for caravans and light trailers. Dimensions
01/712196 DC : DRAFT SEP 2001 ISO 5145 - CYLINDER VALVE OUTLETS FOR GASES AND GAS MIXTURES - SELECTION AND DIMENSIONING
11/30196431 DC : 0 BS ISO 13074 - ANALOGUE QUARTZ CLOCKS - FITTING DIMENSIONS OF MOVEMENTS TO HANDS
EN 1218-2:2004+A1:2009 Safety of woodworking machines - Tenoning machines - Part 2: Double end tenoning and/or profiling machines fed by chain or chains
05/30030830 DC : 0 ISO 1275 - DOUBLE-PITCH PRECISION ROLLER CHAINS, ATTACHMENTS AND ASSOCIATED CHAIN SPROCKETS FOR TRANSMISSION AND CONVEYORS
PREN 1434-2 : DRAFT 2014 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
12/30263881 DC : 0 BS EN 1870-3 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
BS AU 50-1.5.6:1994 Tyres and wheels. Tyres. Industrial vehicle tyres Specification for cylindrical and conical base rubber solid tyres (metric series), designation, dimensions and marking
BS ISO 3193:2008 Aerospace. Bolts, normal hexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa. Dimensions
I.S. EN ISO 9493:2010 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT: DIAL TEST INDICATORS (LEVER TYPE) - DESIGN AND METROLOGICAL CHARACTERISTICS
05/30107533 DC : DRAFT JUL 2005 ISO 10303-224 - INDUSTRIAL AUTOMATION SYSTEMS AND INTEGRATION - PRODUCT DATA REPRESENTATION AND EXCHANGE - PART 224: APPLICATION PROTOCOL - MECHANICAL PRODUCT DEFINITION FOR PROCESS PLANNING USING MACHINING FEATURES
ISO 5291:2011 Belt drives — Grooved pulleys for joined classical V-belts — Groove sections AJ, BJ, CJ and DJ (effective system)
NF ISO 14368-2 : 2008 MINERAL AND SAPPHIRE WATCH-GLASSES - PART 2: ASSEMBLY TO THE CASE BY ADHESIVE OR USING A GASKET
08/30184317 DC : DRAFT JUNE 2008 BS ISO 8139 - PNEUMATIC FLUID POWER - CYLINDERS, 1000 KPA (10 BAR) SERIES - MOUNTING DIMENSIONS OF ROD END SPHERICAL EYES
NF ENV 1090-1 : 96 FD EXECUTION OF STEEL STRUCTURES - PART 1: GENERAL RULES AND RULES FOR BUILDINGS
I.S. EN ISO 286-1:2010/AC:2013 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS (ISO 286-1:2010)
98/715116 DC : DRAFT SEP 1998 ISO/CD 6981 - HYDRAULIC FLUID POWER - CYLINDERS - ROD END PLAIN EYES - MOUNTING DIMENSIONS
BS ISO 14856:2001 Timekeeping instruments. Wristwatch cases. Fixing dimensions of non-spring-bar types
BS EN ISO 14638:2015 Geometrical product specifications (GPS). Matrix model
96/709929 DC : DRAFT JUL 1996 ISO/CD 7368 - HYDRAULIC FLUID POWER - TWO-PORT SLIP-IN CARTRIDGE VALVES - CAVATIES
BS ISO 8135:1999 Hydraulic fluid power. Single rod cylinders, 16 MPa (160 bar) medium and 25 MPa (250 bar) series. Tolerances
ISO 29262:2011 Production equipment for microsystems Interface between end effector and handling system
03/105714 DC : DRAFT MAR 2003 ISO 24234 - DENTISTRY - MERCURY AND ALLOYS FOR DENTAL AMALGAM
DIN ISO 8140:2011-01 Pneumatic fluid power - Cylinders, 1000 kPa (10 bar) series - Mounting dimensions of rod-end clevises (ISO 8140:2009)
BS ISO 3030:2011 Rolling bearings. Radial needle roller and cage assemblies. Boundary dimensions and tolerances
01/711081 DC : DRAFT AUGUST 2001 BS ISO 606 - SHORT-PITCH TRANSMISSION PRECISION ROLLER CHAINS AND SPROCKETS
17/30359229 DC : DRAFT SEP 2017 BS EN 13236 - SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS
XP PREN 3855 : 1995 XP AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - CAPS
DIN ISO 3019-2:2004-02 Hydraulic fluid power - Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors - Part 2: Metric series (ISO 3019-2:2001)
DIN ISO 22917:2005-10 PRECISION SUPERABRASIVES - LIMIT DEVIATIONS AND RUN-OUT TOLERANCES FOR GRINDING WHEELS WITH DIAMOND OR CUBIC BORON NITRIDE (ISO 22917:2016)
BS ISO 8116-2:2008 Textile machinery and accessories. Beams for winding Warper\'s beams
ISO 22037:2007 Solid end mills with corner radii and cylindrical shanks made of hard cutting materials — Dimensions
BS EN 16752:2015 Centrifugal pumps. Test procedure for seal packings
17/30332783 DC : 0 BS ISO 5145 - GAS CYLINDERS - CYLINDER VALVE OUTLETS FOR GASES AND GAS MIXTURES - SELECTION AND DIMENSIONING
06/30154588 DC : DRAFT AUG 2006 ISO 6621-1 - INTERNAL COMBUSTION ENGINES - PISTON RINGS - PART 1: VOCABULARY
BS ISO 10190:2008 Motor cycle chains. Characteristics and test methods
16/30346081 DC : 0 BS EN 4510 - AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREE, SPHERICAL IN TITANIUM ALLOY TIP64001 - ADAPTERS, STRAIGHT, DOUBLE END, WITH LOCKING RING
10/30214867 DC : 0 BS EN ISO 21049 - PUMPS - SHAFT-SEALING SYSTEMS FOR CENTRIFUGAL AND ROTARY PUMPS
UNI EN ISO 5821 : 2010 RESISTANCE WELDING - SPOT WELDING ELECTRODE CAPS
03/300201 DC : DRAFT FEB 2003 IEC 60079-0 ED.4.0 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 0: GENERAL REQUIREMENTS
ISO 3031:2000 Rolling bearings Thrust needle roller and cage assemblies, thrust washers Boundary dimensions and tolerances
SAE J 2276 : 1998 NUMBERING SYSTEM FOR MULTIPLE DIAMETER CUTTING TOOLS
10/30165712 DC : 0 BS ISO 898-2 - MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES; COARSE THREAD
UNE-EN ISO 4064-2:2015 Water meters for cold potable water and hot water - Part 2: Test methods (ISO 4064-2:2014)
07/30148053 DC : 0 BS ISO 8116-2 - TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 2: WARPER&#39;S BEAMS
02/705659 DC : DRAFT APR 2002 ISO/DIS 21049 - PUMPS - SHAFT SEALING SYSTEMS FOR CENTRIFUGAL AND ROTARY PUMPS
I.S. EN ISO 14638:2015 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MATRIX MODEL (ISO 14638:2015)
API 675 : 2012 POSITIVE DISPLACEMENT PUMPS - CONTROLLED VOLUME FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
07/30163990 DC : 0 BS ISO 14691 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLEXIBLE COUPLINGS FOR MECHANICAL POWER TRANSMISSION - GENERAL PURPOSE APPLICATIONS
BS ISO 9255:2008 Aerospace. Bolts, normal spline head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1100 MPa. Dimensions
BS ISO 6195:2013 Fluid power systems and components. Cylinder-rod wiper-ring housings in reciprocating applications. Dimensions and tolerances
BS ISO 15242-2:2015 Rolling bearings. Measuring methods for vibration Radial ball bearings with cylindrical bore and outside surface
API 674 : 2010(R2016) POSITIVE DISPLACEMENT PUMPS - RECIPROCATING
ISO 13726:2008 Hydraulic fluid power — Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm — Accessory mounting dimensions
BS A 328-2:1999 Accessory drives and mounting flanges (Metric sizes) Dimensions
06/30140321 DC : DRAFT JULY 2006 ISO 15242-4 - ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 4: RADIAL CYLINDRICAL ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
ISO 15917:2012 Solid ball-nosed end mills with cylindrical shanks, made of carbide and ceramic materials
DIN ISO 13012-1:2010-02 Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary dimensions and tolerances for series 1 and 3 (ISO 13012-1:2009)
ISO 8116-3:2008 Textile machinery and accessories — Beams for winding — Part 3: Weaver's beams
DIN ISO 286-1:1990-11 ISO SYSTEM OF LIMITS AND FITS - BASES OF TOLERANCES, DEVIATIONS AND FITS
BS ISO 606:2015 Short-pitch transmission precision roller and bush chains, attachments and associated chain sprockets
DIN ISO 1977 E : 2014 CONVEYOR CHAINS, ATTACHMENTS AND SPROCKETS (ISO 1977:2006)
17/30346164 DC : 0 BS ISO 20457 - PLASTICS MOULDED PARTS - TOLERANCES AND ACCEPTANCE CONDITIONS
API 682 CHINESE : 2014 PUMPS - SHAFT SEALING SYSTEMS FOR CENTRIFUGAL AND ROTARY PUMPS
SAE J 1946 : 2007(S2016) COMPANION FLANGES, TYPE A (EXTERNAL PILOT) AND TYPE S (INTERNAL PILOT)
API 674 : 2010 : ERR 2 : 2015 POSITIVE DISPLACEMENT PUMPS - RECIPROCATING
ISO 3030:2011 Rolling bearings Radial needle roller and cage assemblies Boundary dimensions and tolerances
BIS IS 2403 : 2014 SHOR-PITCH TRANSMISSION PRECISION ROLLER AND BUSH CHAINS, ATTACHMENTS AND ASSOCIATED CHAIN SPROCKETS
DIN ISO 10285 E : 2009 ROLLING BEARINGS - SLEEVE TYPE LINEAR BALL BEARINGS - BOUNDARY DIMENSIONS AND TOLERANCES
I.S. EN 13001-3-1:2012 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF COMPETENCE OF STEEL STRUCTURE
UNI EN ISO 898-2 : 2012 MECHANICAL PROPERTIES OF FASTENERS MADE OF CARBON STEEL AND ALLOY STEEL - PART 2: NUTS WITH SPECIFIED PROPERTY CLASSES - COARSE THREAD AND FINE PITCH THREAD
I.S. EN ISO 4064-2:2017 WATER METERS FOR COLD POTABLE WATER AND HOT WATER - PART 2: TEST METHODS (ISO 4064-2:2014)
ISO 16589-1:2011 Rotary shaft lip-type seals incorporating thermoplastic sealing elements — Part 1: Nominal dimensions and tolerances
ISO 3245:2015 Rolling bearings — Needle roller bearings with drawn cup and without inner ring — Boundary dimensions, geometrical product specifications (GPS) and tolerance values
I.S. EN 61076-1:2006&A1:2019 CONNECTORS FOR ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 1: GENERIC SPECIFICATION
DIN ISO 15242-4:2014-06 ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 4: RADIAL CYLINDRICAL ROLLER BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE (ISO 15242-4:2007)
BS EN 1011-6:2005 Welding. Recommendations for welding of metallic materials Laser beam welding
NF EN 1090-2 : 2009 + A1 2011 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
BS ISO 8140:2009 Pneumatic fluid power. Cylinders, 1000 kPa (10 bar) series. Mounting dimensions of rod-end clevises
I.S. EN 61243-3:2014 LIVE WORKING - VOLTAGE DETECTORS - PART 3: TWO-POLE LOW-VOLTAGE TYPE
UNE-EN ISO 204:2010 Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2009)
ISO 12260:2016 Aerospace Screws, pan head, internal offset cruciform ribbed or unribbed drive, stepped shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions
ISO 9304:1989 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes Eddy current testing for the detection of imperfections
ABMA ISO 3096 : 2014 ROLLING BEARINGS - NEEDLE ROLLERS - DIMENSIONS AND TOLERANCES
UNE-EN ISO 1179-2:2014 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)
ISO 6194-1:2007 Rotary shaft lip-type seals incorporating elastomeric sealing elements — Part 1: Nominal dimensions and tolerances
ISO 7649:1991 Clutch housings for reciprocating internal combustion engines Nominal dimensions and tolerances
ISO 14368-1:2000 Mineral and sapphire watch-glasses — Part 1: Dimensions and tolerances
I.S. EN 61243-1:2005 LIVE WORKING - VOLTAGE DETECTORS - PART 1: CAPACITIVE TYPE TO BE USED FOR VOLTAGES EXCEEDING 1 KV A.C.
ISO 10898:2016 Spot drills
ISO 9766:2012 Drills with indexable inserts — Cylindrical shanks with a parallel flat
EN 13236:2010+A1:2015 Safety requirements for superabrasive products
I.S. ENV 1993-2:1997 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 2: STEEL BRIDGES
I.S. EN 1011-6:2006 WELDING - RECOMMENDATION FOR WELDING OF METALLIC MATERIALS - PART 6: LASER BEAM WELDING
I.S. CWA 14949:2004 FUNSTEP AP-APPLICATION INTERPRETED MODEL, INCLUDING VALIDATION GUIDELINES
ISO 4206:2016 Counterbores with parallel shanks and solid pilots
I.S. EN 61241-0:2006 ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 0: GENERAL REQUIREMENTS
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
I.S. EN 175500:1998 CABLE OUTLET ACCESSORIES FOR CONNECTORS, INCLUDING QUALIFICATION APPROVAL AND CAPABILITY APPROVAL (SECTIONAL SPECIFICATION)
ISO 8116-5:2008 Textile machinery and accessories — Beams for winding — Part 5: Sectional beams for warp knitting machines
ISO 8116-2:2008 Textile machinery and accessories — Beams for winding — Part 2: Warper's beams
DIN EN ISO 8750 E : 2007 SPRING-TYPE STRAIGHT PINS - COILED, STANDARD DUTY
DIN EN ISO 8748 E : 2007 SPRING-TYPE STRAIGHT PINS - COILED, HEAVY DUTY
BS EN ISO 10441:2007 Petroleum, petrochemical and natural gas industries. Flexible couplings for mechanical power transmission. Special-purpose applications
UNE-EN ISO 4759-3:2017 Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)
BS EN ISO 12947-1 : 1999 TEXTILES - DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD - PART 1: MARTINDALE ABRASION TESTING APPARATUS
BS EN 1218-3 : 2001 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 3: HAND FED TENONING MACHINES WITH SLIDING TABLE FOR CUTTING STRUCTURAL TIMBERS
ISO 9493:2010 Geometrical product specifications (GPS) Dimensional measuring equipment: Dial test indicators (lever type) Design and metrological characteristics
ISO 8750:2007 Spring-type straight pins Coiled, standard duty
BS EN 3867:2004 Aerospace series. Pipe couplings, loose flanges and seals. Flanges in titanium alloy TI-P64001
BS EN 20286-1:1993 ISO system of limits and fits ISO system of limits and fits. Bases of tolerances, deviations and fits
BS EN ISO 15848-1 : 2015 INDUSTRIAL VALVES - MEASUREMENT, TEST AND QUALIFICATION PROCEDURES FOR FUGITIVE EMISSIONS - PART 1: CLASSIFICATION SYSTEM AND QUALIFICATION PROCEDURES FOR TYPE TESTING OF VALVES (ISO 15848-1:2015)
BS EN 1218-4 : 2004 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 4: EDGE BANDING MACHINES FED BY CHAIN(S)
BS EN 10246-2:2000 Non-destructive testing of steel tubes Automatic eddy current testing of seamless and welded (except submerged arc welded) austenitic and austenitic-ferritic steel tubes for verification of hydraulic leak-tightness
UNE-EN 60079-0:2013 Explosive atmospheres - Part 0: Equipment - General requirements
BS EN 20898-2:1994 Mechanical properties of fasteners Nuts with specified proof load values. Coarse thread
ISO 4064-2:2014 Water meters for cold potable water and hot water Part 2: Test methods
BS EN 3868:2004 Aerospace series. Pipe couplings, loose flanges and seals. Flange connectors, welded, in titanium alloy TI-P64001
ISO 13710:2004 Petroleum, petrochemical and natural gas industries Reciprocating positive displacement pumps
15/30320322 DC : 0 BS ISO 15242-1 - ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 1: FUNDAMENTALS
ISO 9974-3:1996 Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type B)
BS EN 1870-3:2014 Safety of woodworking machines. Circular sawing machines Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
UNE-EN 12750:2013 Safety of woodworking machines - Four sided moulding machines
BS EN 1218-5 : 2004 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FEED CHAIN
ISO 9409-2:2002 Manipulating industrial robots Mechanical interfaces Part 2: Shafts
BS EN 12750:2013 Safety of woodworking machines. Four sided moulding machines
ISO 15912:2016 Dentistry Refractory investment and die material
BS EN ISO 13710:2004 Petroleum, petrochemical and natural gas industries. Reciprocating positive displacement pumps
ISO 898-6:1994 Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread
BS EN 10319-2:2006 Metallic materials. Tensile stress relaxation testing Procedure for bolted joint models
BS EN 3748:2001 Aerospace series. O-ring grooves. Dimensions
BS EN ISO 8748:2007 Spring-type straight pins. Coiled, heavy duty
ISO 9974-2:1996 Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 2: Stud ends with elastomeric sealing (type E)
ISO 14638:2015 Geometrical product specifications (GPS) Matrix model
BS EN 1870-4:2012 Safety of woodworking machines. Circular sawing machines Multiblade rip sawing machines with manual loading and/or unloading
IEC 61243-3:2014 Live working - Voltage detectors - Part 3: Two-pole low-voltage type
ISO 24234:2015 Dentistry Dental amalgam
BS EN ISO 24234 : 2004 DENTISTRY - DENTAL AMALGAM
ISO 14691:2008 Petroleum, petrochemical and natural gas industries — Flexible couplings for mechanical power transmission — General-purpose applications
ISO 10441:2007 Petroleum, petrochemical and natural gas industries Flexible couplings for mechanical power transmission Special-purpose applications
ISO 18217:2015 Safety of woodworking machines Edge-banding machines fed by chain(s)
BS EN 10002-1:2001 Tensile testing of metallic materials Method of test at ambient temperature
05/30134569 DC : DRAFT JUN 2005 IEC 60079-0. ED. 5.0 - ELECTRICAL APPARATUS FOR EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS
ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread
ISO 9409-1:2004 Manipulating industrial robots — Mechanical interfaces — Part 1: Plates
ISO 5821:2009 Resistance welding — Spot welding electrode caps
BS ISO 15242-1:2015 Rolling bearings. Measuring methods for vibration Fundamentals
BS EN 10291:2000 Metallic materials. Uniaxial creep testing in tension. Methods of test
BS EN 1993-1-8:2005 Eurocode 3. Design of steel structures Design of joints
BS EN 3853:2002 Aerospace series. Pipe couplings, 60°, spherical, in titanium alloy TI-P64001. Straight unions, threaded
BS EN ISO 8751:2007 Spring-type straight pins. Coiled, light duty
ISO 4759-1:2000 Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C
IEC 61076-1:2006 Connectors for electronic equipment - Product requirements - Part 1: Generic specification
ISO 4759-3:2016 Tolerances for fasteners Part 3: Washers for bolts, screws and nuts Product grades A, C and F
UNE-EN ISO 15848-1:2015 Industrial valves - Measurement, test and qualification procedures for fugitive emissions - Part 1: Classification system and qualification procedures for type testing of valves (ISO 15848-1:2015)
UNE-EN 61243-3:2015 Live working - Voltage detectors - Part 3: Two-pole low-voltage type
UNE-EN 1870-8:2013 Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
ENV 1993-2 : 1997 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 2: STEEL BRIDGES
EN ISO 4759-3:2016 Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)
EN ISO 24234:2015 Dentistry - Dental amalgam (ISO 24234:2015)
EN 3852:2002 Aerospace series - Pipe couplings, 60°, spherical, in titanium alloy TI-P64001 - Straight unions, welded, threaded
ONORM EN 12750 : 2013 SAFETY OF WOODWORKING MACHINES - FOUR-SIDED MOULDING MACHINES
EN ISO 1559 : 2001 DENTAL MATERIALS - ALLOYS FOR DENTAL AMALGAM
EN ISO 4064-2:2017 Water meters for cold potable water and hot water - Part 2: Test methods (ISO 4064-2:2014)
EN ISO 1179-2:2013 Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) (ISO 1179-2:2013)
EN ISO 10441:2007 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)
EN ISO 12947-1:1998/AC:2006 TEXTILES - DETERMINATION OF THE ABRASION RESISTANCE OF FABRICS BY THE MARTINDALE METHOD - PART 1: MARTINDALE ABRASION TESTING APPARATUS
EN 1993-1-8:2005/AC:2009 EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS
EN ISO 9974-2:2000 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E) (ISO 9974-2:1996)
EN 16752:2015 Centrifugal pumps - Test procedure for seal packings
EN ISO 8751:2007 Spring-type straight pins - Coiled, light duty (ISO 8751:2007)
EN 20898-2 : 1993 MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
EN ISO 9493:2010 Geometrical product specifications (GPS) - Dimensional measuring equipment: Dial test indicators (lever type) - Design and metrological characteristics (ISO 9493:2010)
EN 847-1:2017 Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN 3856:2002 Aerospace series - Pipe couplings, 60°, spherical, in titanium alloy TI-P64001 - Swivel nuts for thrust wire
EN 1870-3:2014 Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
EN ISO 15912:2016 Dentistry - Refractory investment and die material (ISO 15912:2016)
EN 3868:2004 Aerospace series - Pipe couplings, loose flanges and seals - Flange connectors, welded, in titanium alloy TI-P64001
EN ISO 8750:2007 Spring-type straight pins - Coiled, standard duty (ISO 8750:2007)
EN 3851:2003 Aerospace series - Pipe couplings, 60°, spherical, in titanium alloy TI-P64001 - Swivel nuts, straight
EN ISO 286-1:2010/AC:2013 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCES, DEVIATIONS AND FITS (ISO 286-1:2010/COR 1:2013)
EN ISO 14691:2008 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications (ISO 14691:2008)
EN ISO 21049:2004 Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)
EN 3748:2001 AEROSPACE SERIES - O-RING GROOVES - DIMENSIONS
EN 3867:2004 Aerospace series - Pipe couplings, loose flanges and seals - Flanges in titanium alloy TI-P64001
EN ISO 5821 : 2009 Resistance welding - Spot welding electrode caps (ISO 5821:2009)
EN 1870-8:2012 Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
EN 1870-4:2012 Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading
EN ISO 13710:2004 Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)
EN 3853 : 2002 Aerospace series - Pipe couplings, 60°, spherical, in titanium alloy TI-P64001 - Straight unions, threaded
EN ISO 898-6 : 1995 MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD
EN ISO 9974-3:2000 Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-to-metal sealing (type B) (ISO 9974-3:1996)
BS ISO 12488-1:2012 Cranes. Tolerances for wheels and travel and traversing tracks General
BS ISO 8116-3:2008 Textile machinery and accessories. Beams for winding Weaver\'s beams
DIN ISO 1275:2012-07 Double-pitch precision roller chains, attachments and associated chain sprockets for transmission and conveyors (ISO 1275:2006)
ISO/TS 17988:2014 Dentistry Corrosion test methods for dental amalgam
09/30206358 DC : DRAFT SEP 2009 BS EN 1870-4 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTI-BLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
BS ISO 14368-2:2003 Mineral and sapphire watch-glasses Assembly to the case by adhesive or using a gasket
BIS IS 14872-3 : 2013 BALL SCREWS - PART 3: ACCEPTANCE CONDITIONS AND ACCEPTANCE TESTS
16/30335541 DC : 0 BS ISO 3548-2 - PLAIN BEARINGS - THIN-WALLED HALF BEARINGS WITH OR WITHOUT FLANGE - PART 2: MEASUREMENT OF WALL THICKNESS AND FLANGE THICKNESS
14/30297394 DC : 0 BS ISO 23748 - AEROSPACE SERIES - O-RING GROOVES - DIMENSIONS
I.S. EN 10246-2:2000 NON-DESTRUCTIVE TESTING OF STEEL TUBES - PART 2: AUTOMATIC EDDY CURRENT TESTING OF SEAMLESS AND WELDED (EXCEPT SUBMERGED ARC-WELDED) AUSTENITIC AND AUSTENITIC-FERRITIC STEEL TUBES FOR VERIFICATION OF HYDRAULIC LEAK-TIGHTNESS
BS ISO 15242-3:2017 Rolling bearings. Measuring methods for vibration Radial spherical and tapered roller bearings with cylindrical bore and outside surface
DIN EN ISO 5821:2010-04 Resistance welding - Spot welding electrode caps (ISO 5821:2009)
BS ISO 12260:2016 Aerospace. Screws, pan head, internal offset cruciform ribbed or unribbed drive, stepped shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa. Dimensions
DIN EN ISO 8434-1 E : 2008 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - PART 1: 24 DEGREE CONE CONNECTORS
BS EN ISO 18217:2015 Safety of woodworking machines. Edge-banding machines fed by chain(s)
DIN EN ISO 14638:2015-12 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - MATRIX MODEL (ISO 14638:2015)
12/30260496 DC : 0 BS EN 12750 - SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
BIS IS 919-1 : 2014 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - ISO CODE SYSTEM FOR TOLERANCES ON LINEAR SIZES - PART 1: BASIS OF TOLERANCE, DEVIATION AND FITS
14/30276846 DC : 0 BS EN ISO 18217 - SAFETY OF WOODWORKING MACHINES - EDGE-BANDING MACHINES FED CHAIN(S)
14/30284271 DC : 0 BS ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
ISO 13012-1:2009 Rolling bearings Accessories for sleeve type linear ball bearings Part 1: Boundary dimensions and tolerances for series 1 and 3
07/30166625 DC : 0 BS ISO 5821 - RESISTANCE SPOT WELDING ELECTRODE CAPS
BS ISO 19259:2015 Plain bearings. Bearings with embedded solid lubricants
DIN 138:2003-04 METAL - CUTTING TOOLS - BORES, KEYWAYS AND DRIVING FEATURES FOR TOOLS WITH PARALLEL BORE AND 1 IN 30 TAPER BORE
BS ISO 20749 : 2017 DENTISTRY - PRE-CAPSULATED DENTAL AMALGAM
05/30129041 DC : DRAFT OCT 2005 ISO 22037 - SOLID END MILLS WITH CORNER RADII AND CYLINDRICAL SHANKS MADE OF HARD CUTTING MATERIALS - DIMENSIONS
DD ISO/TS 3669-2:2007 Vacuum technology. Bakable flanges Dimensions of knife-edge flanges
BS EN 60603-1:2000 Connectors for frequencies below 3 MHz for use with printed boards Generic specification. General requirements and guide for the preparation of detail specifications with assessed quality
BS ISO 13726:2008 Hydraulic fluid power. Single rod cylinders, 16 MPa (160 bar) compact series with bores from 250 mm to 500 mm. Accessory mounting dimensions
05/30128689 DC : DRAFT FEB 2005 ISO 3186 - AEROSPACE - BOLTS, LARGE BIHEXAGONAL HEAD, NORMAL SHANK, SHORT OR MEDIUM-LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES 1 250 MPA TO 1800 MPA - DIMENSION
BS ISO 1132-2:2001 Rolling bearings. Tolerances Measuring and gauging principles and methods
BS EN ISO 5821:2009 Resistance welding. Spot welding electrode caps
BS ISO 3408-3:2006 Ball screws Acceptance conditions and acceptance tests
ISO 1977:2006 Conveyor chains, attachments and sprockets
API 611 REDLINE : 2008 GENERAL-PURPOSE STEAM TURBINES FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES
15/30320325 DC : 0 BS ISO 15242-2 - ROLLING BEARINGS - MEASURING METHODS FOR VIBRATION - PART 2: RADIAL BALL BEARINGS WITH CYLINDRICAL BORE AND OUTSIDE SURFACE
BS ISO 14691:1999 Petroleum and natural gas industries. Flexible couplings for mechanical power transmission. General purpose applications
BS ISO 23748:2016 Aerospace series. O-ring grooves. Dimensions
BS ISO 13942:2000 Bonded abrasive products. Limit deviations and run-out tolerances
BS 6186-1:Addendum No. 1:1993 Specification for straight cylindrical involute splines: metric module, side fit Inspection
06/30143306 DC : DRAFT SEP 2006 ISO 11001-3 - AGRICULTURAL WHEELED TRACTORS AND IMPLEMENTS - THREE-POINT HITCH COUPLERS - PART 3: LINK COUPLER
BS ISO 6194-1:2007 Rotary shaft lip-type seals incorporating elastomeric sealing elements Nominal dimensions and tolerances
CEI EN 50243 : 2002 OUTDOOR BUSHINGS FOR 24 KV AND 36 KV AND FOR 5 KA AND 8 KA, FOR LIQUID FILLED TRANSFORMERS
I.S. EN 16752:2015 CENTRIFUGAL PUMPS - TEST PROCEDURE FOR SEAL PACKINGS
13/30274174 DC : 0 BS ISO 8133 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR ACCESSORIES FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) COMPACT SERIES
07/30168042 DC : 0 BS ISO 26622-1 - MODULAR TAPER INTERFACE WITH BALL TRACK SYSTEM - PART 1: DIMENSIONS AND DESIGNATION OF SHANKS
BS ISO 4205:2016 Countersinks, 90°, with parallel shanks and solid pilots
DIN ISO 8139:2011-01 Pneumatic fluid power - Cylinders, 1 000 kPa (10 bar) series - Mounting dimensions of rod-end spherical eyes (ISO 8139:2009)
04/104967 DC : DRAFT APR 2004 ISO/DIS 10766 - HYDRAULIC FLUID POWER - CYLINDERS - HOUSING DIMENSIONS FOR RECTANGULAR-SECTION-CUT BEARING RINGS FOR PISTONS AND RODS
04/30098205 DC : DRAFT JUL 2004 ISO 8132 - HYDRAULIC FLUID POWER - SINGLE ROD CYLINDERS, (16 MPA) 160 BAR MEDIUM AND 25 MPA (250 BAR) SERIES - MOUNTING DIMENSIONS FOR ACCESSORIES
API 671 : 2007 : R2010 SPECIAL PURPOSE COUPLINGS FOR PETROLEUM, CHEMICAL AND GAS INDUSTRY SERVICES
05/30128674 DC : DRAFT FEB 2005 ISO 3185 - AEROSPACE - BOLTS, NORMAL BIHEXAGONAL HEAD, NORMAL SHANK, SHORT OR MEDIUM-LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES LESS THAN OR EQUAL TO 1100 MPA - DIMENSIONS
BS ISO 6526:2017 Plain bearings. Pressed bimetallic half thrust washers. Features and tolerances
I.S. EN ISO 12215-8:2009 SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 8: RUDDERS
BS ISO 4401:2005 Hydraulic fluid power. Four-port directional control valves. Mounting surfaces
BS ISO 3245:2015 Rolling bearings. Needle roller bearings with drawn cup and without inner ring. Boundary dimensions, geometrical product specifications (GPS) and tolerance values
UNE-EN ISO 18217:2016 Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
05/30128680 DC : DRAFT FEB 2005 ISO 5856 - AEROSPACE - SCREWS, 100 DEGREES NORMAL COUNTERSUNK HEAD, INTERNAL OFFSET CRUCIFORM RIBBED OR UNRIBBED DRIVE, NORMAL SHANK, SHORT- OR MEDIUM-LENGTH MJ THREADS, METALLIC MATERIAL, COATED OR UNCOATED, STRENGTH CLASSES LESS THAN OR EQUAL TO 1100 MPA - DIMENSION
02/705139 DC : DRAFT APR 2002 PREN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING
PREN 3853 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL, IN TITANIUM ALLOY TI-P64001 - STRAIGHT UNIONS, THREADED
16/30328610 DC : 0 BS ISO 20749 - DENTISTRY - PRE-CAPSULATED DENTAL AMALGAM
ISO 13074:2012 Analogue quartz clocks — Fitting dimensions of movements to hands
ISO 20054:2016 Plain bearings Bearings containing dispersed solid lubricants
UNE-ISO 3408-3:2011 Ball screws -- Part 3: Acceptance conditions and acceptance tests
DIN EN ISO 204 E : 2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
DIN ISO 8116-5 E : 2009 TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 5: SECTIONAL BEAMS FOR WARP KNITTING MACHINES
API 682 : 2014 PUMPS - SHAFT SEALING SYSTEMS FOR CENTRIFUGAL AND ROTARY PUMPS
PREN 3867 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGES IN TITANIUM ALLOY TI-P64001
PREN 4016 : 200P1 AEROSPACE SERIES - OVERSIZED BOLTS
BS ISO 16589-1 : 2011 ROTARY SHAFT LIP-TYPE SEALS INCORPORATING THERMOPLASTIC SEALING ELEMENTS - PART 1: NOMINAL DIMENSIONS AND TOLERANCES
PREN 3855 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, 60 DEGREES, SPHERICAL IN TITANIUM ALLOY TI-P64001 - CAPS
NF ISO 14368-1 : 2008 MINERAL AND SAPPHIRE WATCH-GLASSES - PART 1: DIMENSIONS AND TOLERANCES
PREN 3868 : 200P1 AEROSPACE SERIES - PIPE COUPLINGS, LOOSE FLANGES AND SEALS - FLANGE CONNECTORS, WELDED, IN TITANIUM ALLOY TI-P64001
UNI EN ISO 9493 : 2010 GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL MEASURING EQUIPMENT: DIAL TEST INDICATORS (LEVER TYPE) - DESIGN AND METROLOGICAL CHARACTERISTICS
BS ISO 20332:2016 Cranes. Proof of competence of steel structures
ISO 16399:2014 Meters for irrigation water
I.S. EN 1090-2:2008 EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
ISO 9765:1990 Submerged arc-welded steel tubes for pressure purposes Ultrasonic testing of the weld seam for the detection of longitudinal and/or transverse imperfections
I.S. EN ISO 14691:2008 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLEXIBLE COUPLINGS FOR MECHANICAL POWER TRANSMISSION - GENERAL-PURPOSE APPLICATIONS
BS ISO 3547-2:2017 Plain bearings. Wrapped bushes Test data for outside and inside diameters
BS ISO 8139:2009 Pneumatic fluid power. Cylinders, 1000 kPa (10 bar) series. Mounting dimensions of rod-end spherical eyes
ISO 1275:2006 Double-pitch precision roller chains, attachments and associated chain sprockets for transmission and conveyors
I.S. EN 50109-2-4:1997 HAND CRIMPING TOOLS - TOOLS FOR THE CRIMP TERMINATION OF ELECTRIC CABLES AND WIRES FOR LOW FREQUENCY AND RADIO FREQUENCY APPLICATIONS - PART 2-4: PARTICULAR REQUIREMENTS FOR CENTRE CONTACTS OF RF CONNECTORS, SERIES SMZ
DIN EN 13001-3-1:2013-12 CRANES - GENERAL DESIGN - PART 3-1: LIMIT STATES AND PROOF COMPETENCE OF STEEL STRUCTURE
BS EN 1434-2 : 2015 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
ISO 20749:2017 Dentistry — Pre-capsulated dental amalgam
I.S. EN 1434-2:2015 HEAT METERS - PART 2: CONSTRUCTIONAL REQUIREMENTS
BS EN ISO 204:2009 Metallic materials. Uniaxial creep testing in tension. Method of test
EN ISO 18217:2015 Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
ISO 12488-1:2012 Cranes — Tolerances for wheels and travel and traversing tracks — Part 1: General
UNI EN ISO 204 : 2009 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
BS 4480-9:1995 Plain bearings: metric series Checking the outside diameter of wrapped bushes
17/30353548 DC : 0 BS EN 10277 - BRIGHT STEEL PRODUCTS - TECHNICAL DELIVERY CONDITIONS
ISO 3019-2:2001 Hydraulic fluid power Dimensions and identification code for mounting flanges and shaft ends of displacement pumps and motors Part 2: Metric series
UNI EN ISO 1179-2 : 2013 CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ISO 228-1 THREADS WITH ELASTOMERIC OR METAL-TO-METAL SEALING - PART 2: HEAVY-DUTY (S SERIES) AND LIGHT-DUTY (L SERIES) STUD ENDS WITH ELASTOMERIC SEALING (TYPE E)
BS EN 847-1:2017 Tools for woodworking. Safety requirements Milling tools, circular saw blades
BS EN 61076-1:2006 Connectors for electronic equipment. Product requirements Generic specification
UNE-ISO 16399:2016 Meters for irrigation water
EN ISO 204:2009 Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2009)
ISO 3547-5:2007 Plain bearings Wrapped bushes Part 5: Checking the outside diameter
I.S. EN 13236:2010 SAFETY REQUIREMENTS FOR SUPERABRASIVE PRODUCTS
ISO 1206:2018 Rolling bearings — Needle roller bearings with machined rings — Boundary dimensions, geometrical product specifications (GPS) and tolerance values
ISO 3547-2:2017 Plain bearings — Wrapped bushes — Part 2: Test data for outside and inside diameters
ISO 6982:1992 Hydraulic fluid power Cylinders Rod end spherical eyes Mounting dimensions
IEC 60807-1:1991 Rectangular connectors for frequencies below 3 MHz - Part 1:Generic specification - General requirements and guide for thepreparation of detail specifications for connectors with assessedquality
DIN EN 1870-4:2012-06 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
ISO 10303-224:2006 Industrial automation systems and integration — Product data representation and exchange — Part 224: Application protocol: Mechanical product definition for process planning using machining features
ISO 1132-2:2001 Rolling bearings Tolerances Part 2: Measuring and gauging principles and methods
ISO 3601-2:2016 Fluid power systems — O-rings — Part 2: Housing dimensions for general applications
ISO 5145:2017 Gas cylinders — Cylinder valve outlets for gases and gas mixtures — Selection and dimensioning
ISO 6981:1992 Hydraulic fluid power — Cylinders — Rod end plain eyes — Mounting dimensions
ISO 27528:2009 Wood-based panels Determination of resistance to axial withdrawal of screws
DIN EN 1218-2:2009-10 Safety of woodworking machines - Tenoning machines - Part 2: Double end tenoning and/or profiling machines fed by chain or chains (includes Amendment A1:2009)
DIN EN ISO 9409-1:2004-09 MANIPULATING INDUSTRIAL ROBOTS - MECHANICAL INTERFACES - PART 1: PLATES
DIN EN ISO 4759-1 E : 2001 TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C
DIN EN 1218-5:2010-02 Safety of woodworking machines - Tenoning machines - Part 5: One side profiling machines with fixed table and feed rollers or feed chain (includes Amendment A1:2009)
BS EN ISO 4759-1:2001 Tolerances for fasteners Bolts, screws, studs and nuts. Product grades A, B and C
BS EN ISO 9409-2:2003 Manipulating industrial robots. Mechanical interfaces Shafts
ISO 1179-2:2013 Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing — Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E)
PD ISO/TR 18569:2004 Safety of machinery. Guidelines for the understanding and use of safety of machinery standards.
BS EN 1870-8:2012 Safety of woodworking machines. Circular sawing machines Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
BS EN 3856:2002 Pipe couplings, 60°, spherical, in titanium alloy TI-P64001. Swivel nuts for thrust wire
ISO 8751:2007 Spring-type straight pins Coiled, light duty
BS EN ISO 9974-2:2000 Connections for general use and fluid power. Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Stud ends with elastomeric sealing (type E)
BS EN ISO 21049:2004 Pumps. Shaft sealing systems for centrifugal and rotary pumps
BS EN 10278:1999 Dimensions and tolerances of bright steel products
EN 10278:1999 Dimensions and tolerances of bright steel products
EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
DIN EN 13411-6:2009-04 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 6: ASYMMETRIC WEDGE SOCKET
DIN EN ISO 8748:2007-07 Spring-type straight pins - Coiled, heavy duty (ISO 8748:2007)
DIN EN ISO 204:2009-10 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
DIN ISO 8116-3:2009-08 TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 3: WEAVER'S BEAMS
DIN ISO 10285:2009-11 ROLLING BEARINGS - SLEEVE TYPE LINEAR BALL BEARINGS - BOUNDARY DIMENSIONS AND TOLERANCES
UNI EN 1218-2 : 2009 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 2: DOUBLE END TENONING AND/OR PROFILING MACHINES FED BY CHAIN OR CHAINS
DIN ISO 8116-2:2009-08 TEXTILE MACHINERY AND ACCESSORIES - BEAMS FOR WINDING - PART 2: WARPER'S BEAMS
EN 10319-2:2006 Metallic materials - Tensile stress relaxation testing - Part 2: Procedure for bolted joint models
EN 10246-2:2000 Non-destructive testing of steel tubes - Part 2: Automatic eddy current testing of seamless and welded (except submerged arc-welded) austenitic and austenitic-ferritic steel tubes for verification of hydraulic leak-tightness
NF EN 1218-5 : 2004 + A1 2010 SAFETY OF WOODWORKING MACHINES - TENONING MACHINES - PART 5: ONE SIDE PROFILING MACHINES WITH FIXED TABLE AND FEED ROLLERS OR FED BY CHAIN
DIN 3861:2002-11 NON-SOLDERING COMPRESSION FITTINGS - COMPRESSION RINGS - DESIGN
DIN EN ISO 8751:2007-07 Spring-type straight pins - Coiled, light duty (ISO 8751:2007)
EN 60603-1:1998 Connectors for frequencies below 3 MHz for use with printed boards - Part 1: Generic specification - General requirements and guide for the preparation of detail specifications, with assessed quality
EN 12750:2013 Safety of woodworking machines - Four sided moulding machines
DIN EN ISO 898-2:2012-08 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread (ISO 898-2:2012)
EN 61241-0:2006 Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements
ASME B32.100 : 2016 PREFERRED METRIC SIZES FOR FLAT, ROUND, SQUARE, RECTANGULAR AND HEXAGONAL METAL PRODUCTS
I.S. EN 10278:2000 DIMENSIONS AND TOLERANCES OF BRIGHT STEEL PRODUCTS

ISO/TR 14638:1995 Geometrical product specification (GPS) Masterplan
ISO 2692:2014 Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR)
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO/R 1938:1971 ISO system of limits and fits Part II : Inspection of plain workpieces

View more information
US$225.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.