ISO 527-2:2012
Withdrawn
Withdrawn
View Superseded by
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
Available format(s)
Hardcopy , PDF
Language(s)
English, French, Russian
Published date
02-22-2012
Withdrawn date
11-02-2025
Superseded by
US$96.00
Excluding Tax where applicable
ISO 527-2:2012 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527‑1.
| Committee |
ISO/TC 61/SC 2
|
| DevelopmentNote |
Supersedes ISO 6239, ISO R 527 (04/2001) Supersedes ISO/DIS 527-2. (02/2012)
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 527-2:2012-06 | Identical |
| JIS K 7161-2:2014 | Identical |
| NBN EN ISO 527-2 : 2012 | Identical |
| NF EN ISO 527-2 : 2012 | Identical |
| NEN EN ISO 527-2 : 2012 | Identical |
| NS EN ISO 527-2 : 2012 | Identical |
| I.S. EN ISO 527-2:2012 | Identical |
| PN EN ISO 527-2 : 2012 | Identical |
| SS-EN ISO 527-2:2012 | Identical |
| BS EN ISO 527-2:1996 | Identical |
| EN ISO 527-2:2012 | Identical |
| BS EN ISO 527-2:2012 | Equivalent |
| DS EN ISO 527-2 : 2012 | Identical |
| BS EN ISO 527-2:2012 | Identical |
| BS 2782-3.322(1994) : 1994 AMD 8639 | Identical |
| UNE-EN ISO 527-2:2012 | Identical |
| UNE-EN ISO 527-2:1997 | Identical |
| 07/30169818 DC : 0 | BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| 07/30168088 DC : DRAFT AUG 2007 | BS EN 13341 AMD 1 - THERMOPLASTICS STATIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED POLYETHYLENE, ROTATIONALLY MOULDED POLYETHYLENE AND POLYAMIDE 6 BY ANIONIC POLYMERIZATION TANKS - REQUIREMENTS AND TEST METHODS |
| BS EN ISO 16396-2:2017 | Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DD CLC/TS 50131-2-7-3:2009 | Alarm systems. Intrusion and hold-up systems Intrusion detectors. Glass break detectors (active) |
| ISO 11963:2012 | Plastics — Polycarbonate sheets — Types, dimensions and characteristics |
| PREN ISO 7792-2 : DRAFT 2011 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 4433-1:1997 | Thermoplastic pipes. Resistance to liquid chemicals. Classification Immersion test method |
| I.S. EN ISO 7792-2:2012 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012) |
| I.S. EN 1013-4:2000 | LIGHT TRANSMITTING PROFILED PLASTIC SHEETING FOR SINGLE SKIN ROOFING - PART 4: SPECIFIC REQUIREMENTS, TEST METHODS AND PERFORMANCE OF POLYCARBONATE (PC) SHEETS |
| 06/30144978 DC : DRAFT JAN 2006 | EN ISO 15014 - PLASTICS - EXTRUDED SHEETS OF POLY(VINYLIDENE FLUORIDE) (PVDF) - REQUIREMENTS AND TEST METHODS |
| 05/30132990 DC : DRAFT APR 2005 | ISO 20753 - PLASTICS - TEST SPECIMENS |
| 13/30240164 DC : 0 | BS ISO 16365-1 - PLASTICS - THERMOPLASTIC POLYURETHANES FOR MOULDING AND EXTRUSION - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| I.S. EN ISO 1874-1:2010 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATION |
| 10/30211370 DC : DRAFT JUNE 2010 | BS ISO 11833-1 - PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM |
| 17/30339707 DC : 0 | BS ISO 21138-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2: PIPES AND FITTINGS WITH SMOOTH EXTERNAL SURFACE, TYPE A |
| BS ISO 6402-2 : 94 AMD 10652 | |
| 16/30334902 DC : 0 | BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS |
| 10/30212123 DC : 0 | BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| 15/30311270 DC : 0 | BS EN ISO 294-5 - PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY |
| DIN EN ISO 1797:2016-05 (Draft) | DENTISTRY - SHANKS FOR ROTARY AND OSCILLATING INSTRUMENTS (ISO 1797:2017) |
| 14/30298693 DC : 0 | BS ISO 18250-8 - CONNECTORS FOR RESERVOIR DELIVERY SYSTEMS FOR HEALTHCARE APPLICATIONS - PART 8: CITRATE-BASED ANTICOAGULANT SOLUTION FOR APHERESIS APPLICATIONS |
| 13/30263803 DC : 0 | BS ISO 17296-4 - ADDITIVE MANUFACTURING - RAPID TECHNOLOGIES (RAPID PROTOTYPING) - PART 4: DATA PROCESSING |
| 06/30136263 DC : DRAFT MAR 2006 | ISO 21138-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLCHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 2 - PIPES AND FITTINGS WITH SMOOTH EXTERNAL SURFACE - TYPE A |
| ASTM D 6778 : 2014 : REDLINE | Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM) |
| I.S. EN 1013-5:2000 | LIGHT TRANSMITTING PROFILED PLASTIC SHEETING FOR SINGLE SKIN ROOFING - PART 5: SPECIFIC REQUIREMENTS, TEST METHODS AND PERFORMANCE OF POLYMETHYLMETHACRYLATE (PMMA) SHEETS |
| I.S. EN ISO 12086-1:2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| 09/30209028 DC : 0 | BS EN 131-2 - LADDERS - PART 2: REQUIREMENTS, TESTING, MARKING |
| BS ISO 10931-1:1997 | Plastics piping systems for industrial applications. Poly (vinylidene fluoride) General |
| BS ISO 20753 : 2008 | PLASTICS - TEST SPECIMENS |
| NF EN ISO 11296-3 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| DIN EN 16506:2014-12 | SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL) |
| 08/30170332 DC : DRAFT JAN 2008 | BS EN ISO 8986-2 - PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ISO 11296-7:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes |
| BS EN 4702-05:2017 | Aerospace series. Quick release fastening systems for non-structural and lining applications Retaining washer |
| BS EN ISO 15527:2013 | Plastics. Compression-moulded sheets of polyethylene (PEUHMW, PE-HD). Requirements and test methods |
| INCITS/ISO/IEC 15521 : 1998 : R2005 | INFORMATION TECHNOLOGY - 3,81 MM WIDE MAGNETIC TAPE CARTRIDGE FOR INFORMATION INTERCHANGE - HELICAL SCAN RECORDING - DDS-3 FORMAT USING 125 M LENGTH TAPES |
| 04/30078983 DC : DRAFT OCT 2004 | ISO 22088-4 - PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 4: BALL OR PIN IMPRESSION METHOD |
| I.S. EN ISO 22088-5:2009 | PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 5: CONSTANT TENSILE DEFORMATION METHOD |
| 05/30091855 DC : DRAFT MAR 2005 | ISO 1874-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 15015:2011-07 | Plastics - Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) - Requirements and test methods (ISO 15015:2011) |
| 04/30078976 DC : DRAFT OCT 2004 | ISO 22088-3 - PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 3: BENT STRIP METHOD |
| BS 7933-2:2007 | Electric cables. Accessories. Material characterisation Fingerprinting and type tests for heat shrinkable components for low voltage applications |
| 15/30315534 DC : 0 | BS EN ISO 16396-2 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 4894-2 : AMD 10662 | PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 60094-4:1994 | Magnetic tape sound recording and reproducing systems Mechanical magnetic tape properties |
| DIN EN 15345:2008-02 | Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates |
| NFC 33 009-2 : 2008 | ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERIZATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS |
| 04/30115317 DC : 0 | BS EN ISO 10350-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS |
| 97/713392 DC : DRAFT AUG 1997 | PREN 4243 - AEROSPACE SERIES - ACRYLIC (PMMA) SHEETS - TECHNICAL SPECIFICATION |
| 12/30240423 DC : 0 | BS ISO 16396-1 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM, MARKING OF PRODUCTS AND BASIS FOR SPECIFICATIONS |
| ISO 11659-2:2004 | Textile machinery and accessories — Machine parts in contact with textile processing oils — Part 2: Determination of the impact on polymeric materials |
| 10/30216993 DC : 0 | BS EN 295-4 - VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 4: REQUIREMENTS FOR ADAPTORS, CONNECTORS AND FLEXIBLE COUPLINGS |
| 12/30192217 DC | BS ISO 12856. Plastic railway sleepers (railroad ties) |
| BS EN 60216-2:2005 | Electrical insulating materials. Thermal endurance properties Determination of thermal endurance properties of electrical insulating materials. Choice of test criteria |
| ASTM D 6835 : 2017 : REDLINE | Standard Classification System for Thermoplastic Elastomer-Ether-Ester Molding and Extrusion Materials (TEEE) |
| 07/30152076 DC : 0 | BS ISO 25137-2 - PLASTICS - SULFONE PLASTICS (SP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 05/30132152 DC : DRAFT APR 2005 | ISO 21004 - PLASTICS PIPING SYSTEMS - MULTILAYER PIPES AND THEIR JOINTS, BASED ON THERMOPLASTICS, FOR WATER SUPPLY |
| ISO 11296-3:2009 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 3: Lining with close-fit pipes |
| PREN 4366 : 200P1 | AEROSPACE SERIES - HEAT AND CRAZING RESISTANT CAST ACRYLIC, CROSSLINKED, MULTI-AXIALLY STRETCHED, AND LOW MOISTURE ABSORPTION - PROPERTIES |
| I.S. EN 15502-2-1:2012 | GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| API RP 17B : 2014 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
| PREN 2719 : 200P1 | AEROSPACE SERIES - POLYCARBONATE SHEET - TECHNICAL SPECIFICATION |
| DIN EN ISO 16396-2:2017-07 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| DIN EN ISO 11296-4:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| PREN 4243 : 200P1 | AEROSPACE SERIES - CAST ACRYLIC SHEETS - TECHNICAL SPECIFICATION |
| I.S. EN 50131-2-8:2016 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 2-8: INTRUSION DETECTORS - SHOCK DETECTORS |
| ISO/IEC 15521:1998 | Information technology — 3,81 mm wide magnetic tape cartridge for information interchange — Helical scan recording — DDS-3 format using 125 m length tapes |
| S.R. CLC/TS 50131-2-7-3:2009 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 2-7-3: INTRUSION DETECTORS - GLASS BREAK DETECTORS (ACTIVE) |
| API SPEC 17J : 2014 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
| I.S. EN 15345:2007 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYPROPYLENE (PP) RECYCLATES |
| ISO 20029-2:2017 | Plastics — Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties |
| ISO 18872:2007 | Plastics — Determination of tensile properties at high strain rates |
| I.S. EN ISO 294-5:2017 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY (ISO 294-5:2017) |
| I.S. EN ISO 15527:2013 | PLASTICS - COMPRESSION-MOULDED SHEETS OF POLYETHYLENE (PE-UHMW, PE-HD) - REQUIREMENTS AND TEST METHODS (ISO 15527:2010) |
| I.S. EN 16506:2014 | SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL) |
| ISO 20557-2:2018 | Plastics — Poly(phenylene ether) (PPE) moulding and extrusion materials — Part 2: Preparation of test specimen and determination of properties |
| I.S. EN ISO 1797:2017 | DENTISTRY - SHANKS FOR ROTARY AND OSCILLATING INSTRUMENTS (ISO 1797:2017) |
| I.S. EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| I.S. EN ISO 20029-2:2018 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES (ISO 20029-2:2017) |
| HD 631.2 : 2007 | ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS |
| I.S. EN 124-5:2015 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS |
| EN ISO 899-1:2017 | Plastics - Determination of creep behaviour - Part 1: Tensile creep (ISO 899-1:2017) |
| ISO 11833-1:2012 | Plastics — Unplasticized poly(vinyl chloride) sheets — Types, dimensions and characteristics — Part 1: Sheets of thickness not less than 1 mm |
| DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| EN ISO 9093-2:2002 | Small craft - Seacocks and through-hull fittings - Part 2: Non-metallic (ISO 9093-2:2002) |
| I.S. EN ISO 11296-7:2013 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011) |
| 16/30317348 DC : 0 | BS EN 15860 - PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| NACE RP 03 04 : 2004 | DESIGN, INSTALLATION, AND OPERATION OF THERMOPLASTIC LINERS FOR OILFIELD PIPELINES |
| EN ISO 11296-3:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011) |
| ASTM D 6779 : 2017 : REDLINE | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 5927 : 2017 : REDLINE | Standard Classification System for and Basis for Specifications for Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test Methods |
| I.S. EN 14963:2006 | ROOF COVERINGS - CONTINUOUS ROOFLIGHTS OF PLASTICS WITH OR WITHOUT UPSTANDS - CLASSIFICATION, REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 899-1:2017 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP (ISO 899-1:2017) |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| ASTM D 6865 : 2017 : REDLINE | Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials |
| IEC 60079-7:2015+AMD1:2017 CSV | Explosive atmospheres - Part 7: Equipment protection by increased safety "e" |
| I.S. EN ISO 11963:2012 | PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012) |
| I.S. EN ISO 11833-1:2012 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| I.S. EN 12566-3:2016 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| ISO 21809-3:2016 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings |
| EN IEC 60079-7:2015/A1:2018 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017) |
| DIN EN 13341:2011-04 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods (includes Amendment A1:2011) |
| DIN EN ISO 15103-2:2007-09 | PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 4613-2:2004-12 | PLASTICS - ETHYLENE/VINYL ACETATE (E/VAC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 26:2015-08 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| BS EN ISO 4613-2:1995 | Plastics. Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 14471 : 2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| BS EN ISO 23667:2007 | Packaging. Transport packaging for dangerous goods. Rigid plastics and plastics composite IBCs. Compatibility testing |
| BS EN 15347:2007 | Plastics. Recycled Plastics. Characterization of plastics waste |
| BS EN ISO 13628-2:2006 | Petroleum and natural gas industries. Design and operation of subsea production systems Unbonded flexible pipe systems for subsea and marine applications |
| BS EN 10288:2002 | Steel tubes and fittings for onshore and offshore pipelines. External two layer extruded polyethylene based coatings |
| BS EN ISO 11542-2 : 1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 1622-2:1999 | Plastics. Polystrene (PS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 13677-2:2003 | Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements |
| BS EN 295-3:2012 | Vitrified clay pipe systems for drains and sewers Test methods |
| ISO 13628-11:2007 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 11: Flexible pipe systems for subsea and marine applications |
| BS EN 1873 : 2014 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| BS EN ISO 12086-1:2006 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Designation system and basis for specifications |
| BS EN 14628:2005 | Ductile iron pipes, fittings and accessories. External polythene coating for pipes. Requirements and test methods |
| BS EN ISO 3167:2014 | Plastics. Multipurpose test specimens |
| ISO 15103-2:2007 | Plastics — Poly(phenylene ether) (PPE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 19069-2:2016 | Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 15015:2011 | Plastics — Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) — Requirements and test methods |
| BS EN ISO 16103:2005 | Packaging. Transport packages for dangerous goods. Recycled plastics material |
| BS EN ISO 2580-2:2003 | Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DIN EN ISO 1872-2:2000-12 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 7823-1:2003 | PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: CAST SHEETS |
| I.S. EN ISO 2580-2:2004 | PLASTICS - ACRYLONITRILE/BUTADIENE/STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 89:2015 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| EN 13349:2002 | Copper and coppper alloys - Pre-insulated copper tubes with solid covering |
| EN 13566-2:2005 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 2: Lining with continuous pipes |
| EN 13575:2012 | Static thermoplastic tanks for the above ground storage of chemicals — Blow moulded or rotationally moulded polyethylene tanks — Requirements and test methods |
| EN 61234-2:1998 | Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets |
| DIN EN ISO 12086-1:2006-05 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| EN 10245-1:2011 | Steel wire and wire products - Organic coatings on steel wire - Part 1: General rules |
| CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products |
| DIN ISO 23013:2017-10 | ROAD VEHICLES - DETERMINATION OF RESISTANCE TO FORCED ENTRY OF SECURITY GLASS CONSTRUCTIONS USED IN VEHICLE GLAZING - TEST OF GLAZING SYSTEMS (ISO 23013:2016) |
| DIN EN ISO 8257-2:2006-06 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 12566-3:2016 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| EN 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| EN 1013-4:2000 | Light transmitting profiled plastic sheeting for single skin roofing - Part 4: Specific requirements, test methods and performance of polycarbonate (PC) sheets |
| EN 10288:2002 | Steel tubes and fittings for onshore and offshore pipelines - External two layer extruded polyethylene based coatings |
| EN ISO 11439:2013 | Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013) |
| EN 1013:2012+A1:2014 | Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods |
| EN 124-5:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials |
| EN 13341:2005+A1:2011 | Static thermoplastic tanks for above ground storage of domestic heating oils, kerosene and diesel fuels - Blow moulded and rotationally moulded polyethylene tanks and rotationally moulded tanks made of anionically polymerized polyamide 6 - Requirements and test methods |
| EN 50131-2-8:2016 | Alarm systems - Intrusion and hold-up systems - Part 2-8: Intrusion detectors - Shock detectors |
| DIN EN 15502-2-1:2017-09 | Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW (includes Amendment 1:2016) |
| DIN EN ISO 178:2013-09 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013) |
| EN ISO 23667:2007 | Packaging - Transport packaging for dangerous goods - Rigid plastics and plastics composite IBCs - Compatibility testing (ISO 23667:2007) |
| DIN EN ISO 3672-2:2002-07 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 1337-5:2005 | Structural bearings - Part 5: Pot bearings |
| DIN EN ISO 11296-7:2013-05 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011) |
| I.S. EN 13200-4:2006 | SPECTATOR FACILITIES - PART 4: SEATS - PRODUCT CHARACTERISTICS |
| NBR IEC 60079-0 : 2013 ERRATA 2 2016 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| DIN EN ISO 11296-3:2011-07 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| 02/103631 DC : DRAFT MAY 2002 | BS EN 14471 - CHIMNEYS - REQUIREMENTS AND TEST METHODS FOR SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS |
| DIN EN ISO 22088-5:2009-10 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 5: Constant tensile deformation method (ISO 22088-5:2006) |
| DIN EN ISO 6259-3:2015-11 | THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 3: POLYOLEFIN PIPES (ISO 6259-3:2015) |
| 12/30275810 DC : 0 | BS EN 16506 - SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL) |
| 12/30255180 DC : 0 | BS EN ISO 11403-1 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES |
| 13/30276234 DC : 0 | BS EN 15346 - PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLY(VINYL CHLORIDE) (PVC) RECYCLATES |
| 10/30196141 DC : 0 | BS ISO 11119-3 - GAS CYLINDERS OF COMPOSITE CONSTRUCTION - SPECIFICATION AND TEST METHODS - PART 3: FULLY WRAPPED FIBRE REINFORCED COMPOSITE GAS CYLINDERS AND TUBES WITH NON-METALLIC AND NON-LOAD SHARING METAL LINERS |
| ISO 4433-1:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
| I.S. EN 4702-03:2017 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING |
| BIS IS 8504-2 : 2013 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
| I.S. EN ISO 12086-2:2006 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 14/30304058 DC : 0 | BS EN ISO 17855-2 - PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ISO 22621-1:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) — Polyamide (PA) — Part 1: General |
| BS ISO 25137-2 : 2009 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 50290-2-23:2013 | Communication cables Common design rules and construction. Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables |
| 03/300201 DC : DRAFT FEB 2003 | IEC 60079-0 ED.4.0 - ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES - PART 0: GENERAL REQUIREMENTS |
| 17/30339710 DC : 0 | BS ISO 21138-3 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: PIPES AND FITTINGS WITH NON-SMOOTH EXTERNAL SURFACE, TYPE B |
| 04/30091878 DC : DRAFT FEB 2004 | BS EN ISO 13000-2 - PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 17/30345075 DC : 0 | BS EN ISO 11296-4 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| 17/30349217 DC : 0 | BS EN ISO 21970-2 - PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ISO 12215-5:2008 | Small craft — Hull construction and scantlings — Part 5: Design pressures for monohulls, design stresses, scantlings determination |
| 11/30237918 DC : 0 | BS EN ISO 13274 - PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING FOR PACKAGING AND IBCS |
| BS EN ISO 20028-2:2017 | Plastics. Thermoplastic polyester (TP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| 12/30258334 DC : 0 | BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTIC SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| EN 15344:2007 | Plastics - Recycled Plastics - Characterisation of Polyethylene (PE) recyclates |
| 17/30342710 DC : 0 | BS EN ISO 12215-5 - SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION |
| BS EN 50131-2-8:2016 | Alarm systems. Intrusion and hold-up systems Intrusion detectors. Shock detectors |
| BS EN ISO 22088-6:2009 | Plastics. Determination of resistance to environmental stress cracking (ESC) Slow strain rate method |
| 98/123516 DC : DRAFT JULY 1998 | PREN 13121-1 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - ACCEPTANCE CONDITIONS AND USAGE CONDITIONS |
| I.S. EN ISO 19069-2:2016 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| IEC 62642-2-71:2015 | Alarm systems - Intrusion and hold-up systems - Part 2-71: Intrusion detectors - Glass break detectors (acoustic) |
| S.R. CLC/TS 50131-2-7-1:2009 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 2-7-1: INTRUSION DETECTORS - GLASS BREAK DETECTORS (ACOUSTIC) |
| 05/30102804 DC : DRAFT MAY 2005 | ISO 18872 - PLASTICS - DETERMINATION OF TENSILE PROPERTIES AT HIGH STRAIN RATES |
| ISO 18263-2:2015 | Plastics — Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging — Part 2: Preparation of test specimens and determination of properties |
| PREN 438-9 : DRAFT 2016 | HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| BS EN 15534-1 : 2014 | COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| PREN ISO 1874-1 : DRAFT 2008 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION |
| 10/30233680 DC : 0 | BS EN 13575 - STATIC THERMOPLASTIC TANKS FOR THE ABOVE GROUND STORAGE OF CHEMICALS - BLOW MOULDED OR ROTATIONALLY MOULDED POLYETHYLENE TANKS - REQUIREMENTS AND TEST METHODS |
| DIN ISO 16486-1:2015-07 | Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2012 + AMD 1:2014) |
| PREN ISO 11403-1 : DRAFT 2012 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO/DIS 11403-1:2012) |
| EN 4702-05:2017 | Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer |
| BS ISO 17194:2007 | Structural adhesives. A standard database of properties |
| 17/30360679 DC : DRAFT SEP 2017 | BS EN 17152-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND CONVEYANCE AND STORAGE OF NON-POTABLE WATER - BOXES USED FOR INFILTRATION, ATTENUATION AND STORAGE SYSTEMS - PART 1: SPECIFICATIONS FOR STORM WATER BOXES MADE OF PP AND PVC |
| DIN EN ISO 19069-2:2016-07 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
| DD ISO/TS 15869:2009 | Gaseous hydrogen and hydrogen blends. Land vehicle fuel tanks |
| I.S. EN ISO 13274:2013 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING FOR PACKAGING AND IBCS (ISO 13274:2013) |
| I.S. EN ISO 6259-3:2015 | THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 3: POLYOLEFIN PIPES (ISO 6259-3:2015) |
| I.S. EN ISO 16396-2:2017 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 16396-2:2017) |
| 11/30250549 DC : 0 | BS EN 14471 - CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| 08/30161535 DC : 0 | BS EN ISO 1874-1 - PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION |
| BS ISO 2897-2 : 1994 AMD 10661 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 04/30109201 DC : DRAFT OCT 2004 | EN 14879-2 - ORGANIC COATING SYSTEMS AND LININGS FOR PROTECTION OF INDUSTRIAL APPARATUS AND PLANTS AGAINST CORROSION CAUSED BY AGGRESSIVE MEDIA - PART 2: COATINGS ON METALLIC COMPONENTS |
| ISO 15014:2007 | Plastics — Extruded sheets of poly(vinylidene fluoride) (PVDF) — Requirements and test methods |
| BS ISO 7391-2 : 1996 AMD 10746 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 15/30330892 DC : 0 | BS ISO 9349 - PREINSULATED DUCTILE IRON PIPELINE SYSTEMS |
| 04/30081681 DC : DRAFT OCT 2004 | ISO 22088-6 - PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 6: SLOW STRAIN RATE METHOD |
| BS ISO 8257-2:1990 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DD CEN/TS 15534-1:2007 | Wood-plastics composites (WPC) Test methods for characterisation of WPC materials and products |
| INCITS/ISO/IEC 15521 : 1998 | INFORMATION TECHNOLOGY - 3,81 MM WIDE MAGNETIC TAPE CARTRIDGE FOR INFORMATION INTERCHANGE - HELICAL SCAN RECORDING - DDS-3 FORMAT USING 125 M LENGTH TAPES |
| 04/30078973 DC : DRAFT OCT 2004 | ISO 22088-2 - PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 2: CONSTANT TENSILE STRESS METHOD |
| BS EN 50465:2015 | European product standard for combined heating power systems using gas fuel |
| EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| PREN 4365 : 200P1 | AEROSPACE SERIES - HEAT AND CRAZING RESISTANT CAST ACRYLIC, CROSSLINKED, AND LOW MOISTURE ABSORPTION - PROPERTIES |
| I.S. EN ISO 7391-2:2006 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| PREN 15860 : DRAFT 2016 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| SAE J2749_201707 | High Strain Rate Tensile Testing of Polymers |
| BS ISO 28078-2:2009 | Plastics. Poly(phenylene sulfide) (PPS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 21138-3:2007 | Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 3: Pipes and fittings with non-smooth external surface, Type B |
| I.S. EN ISO 178:2010 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010) |
| BS EN 60079-7 : 2015 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015) |
| I.S. EN ISO 20028-2:2017 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| BS EN ISO 20753:2014 | Plastics. Test specimens |
| PREN 131-2 : DRAFT 2009 | LADDERS - PART 2: REQUIREMENTS, TESTING, MARKING |
| PREN 14471 : DRAFT 2011 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| NF EN ISO 11296-4 : 2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES |
| I.S. HD 631.2:2007 | ELECTRIC CABLES - ACCESSORIES - MATERIAL CHARACTERISATION - PART 2: FINGERPRINTING AND TYPE TESTS FOR HEAT SHRINKABLE COMPONENTS FOR LOW VOLTAGE APPLICATIONS |
| I.S. EN ISO 11296-3:2011 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| BS EN ISO 11296-3:2011 | Plastics piping systems for renovation of under ground non-pressure drainage and sewerage networks Lining with close-fit pipes |
| ISO 28078-2:2009 | Plastics — Poly(phenylene sulfide) (PPS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 7823-2:2003 | Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 2: Extruded sheets |
| ISO 16365-2:2014 | Plastics — Thermoplastic polyurethanes for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties |
| (INACTIVE RECORD)ASTM D 5336 : 2015-04 | CLASSIFICATION SYSTEM AND BASIS FOR SPECIFICATION FOR POLYPHTHALAMIDE (PPA) INJECTION MOLDING MATERIALS |
| CLC/TS 50131-2-7-1:2009 | Alarm systems - Intrusion and hold-up systems - Part 2-7-1: Intrusion detectors - Glass break detectors (acoustic) |
| ISO/TS 15869:2009 | Gaseous hydrogen and hydrogen blends — Land vehicle fuel tanks |
| ASTM D 5575 : 2007 : R2013 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| ASTM D 7436 : 2017 : REDLINE | Standard Classification System for Unfilled Polyethylene Plastics Molding and Extrusion Materials with a Fractional Melt Index Using ISO Protocol and Methodology |
| ASTM D 5575 : 2007 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| EN 50465 : 2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| I.S. EN 50465:2015 | GAS APPLIANCES - COMBINED HEAT AND POWER APPLIANCE OF NOMINAL HEAT INPUT INFERIOR OR EQUAL TO 70 KW |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| IEC 62899-201:2016 | Printed electronics - Part 201: Materials - Substrates |
| DIN EN ISO 1874-2:2013-03 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| DIN EN ISO 22088-2:2006-11 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 2: Constant tensile load method (ISO 22088-2:2006) |
| DIN EN 13200-4:2006-12 | Spectator facilities - Part 4: Seats - Product characteristics |
| DIN EN 13566-2:2006-02 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 2: LINING WITH CONTINUOUS PIPES |
| DIN EN 89:2015-08 | GAS-FIRED STORAGE WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| DIN EN ISO 22088-3:2006-11 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 3: Bent strip method (ISO 22088-3:2006) |
| DIN EN ISO 23667:2007-10 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - RIGID PLASTICS AND PLASTICS COMPOSITE IBCS - COMPATIBILITY TESTING |
| DIN EN 15347:2008-02 | Plastics - Recycled Plastics - Characterisation of plastics wastes |
| DIN EN 14427:2014-09 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
| DIN EN 14471:2015-03 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 14530-2:2000-08 | Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14530-2:1999); German version EN ISO 14530-2:1999 |
| DIN EN 1337-5:2005-07 | Structural bearings - Part 5: Pot bearings |
| BS EN ISO 4894-2:1999 | Plastics. Styrene/acrylonitrile (SAN) copolymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 15526-2:2004 | Plastics. Polyketone (PK) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DIN EN ISO 2580-2:2004-05 | PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with cured-in-place pipes |
| ISO 7823-3:2007 | Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 3: Continuous cast sheets |
| BS EN 295-4:2013 | Vitrified clay pipe systems for drains and sewers Requirements for adaptors, connectors and flexible couplings |
| BS EN 26:1998 | Gas fired instantaneous water heaters for the production of domestic hot water, fitted with atmospheric burners |
| BS EN 13566-2:2005 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with continuous pipes |
| BS EN ISO 1874-2:2012 | Plastics. Polyamide (PA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| DIN EN 15274:2015-06 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS EN ISO 7823-3:2007 | Plastics. Poly(methacrylate) sheets. Types, dimensions and characteristics Continuous cast sheets |
| 09/30206527 DC : 0 | BS EN 60079-0 ED 6.0 - EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| BS EN 1337-5:2005 | Structural bearings Pot bearings |
| BS EN 1013-4:2000 | Light transmitting profiled plastic sheeting for single skin roofing Specific requirements, test methods and performance of polycarbonate (PC) sheets |
| BS EN ISO 1872-2:2007 | Plastics. Polyethylene (PE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BIS IS/IEC 60079-0 : 2011 | EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS |
| I.S. EN 15346:2014 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLY(VINYL CHLORIDE) (PVC) RECYCLATES |
| I.S. EN 14471:2013 | CHIMNEYS - SYSTEM CHIMNEYS WITH PLASTIC FLUE LINERS - REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 6259-1:2002-02 | THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL TEST METHOD |
| I.S. EN ISO 15526-2:2004 | PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 6224:2011 | THERMOPLASTICS HOSES, TEXTILE-REINFORCED, FOR GENERAL-PURPOSE WATER APPLICATIONS - SPECIFICATION (ISO 6224:2011) |
| I.S. EN ISO 13628-2:2006 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 2: UNBONDED FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
| I.S. EN ISO 13000-2:2006 | PLASTICS - POLYTETRAFLUOROETHYLENE (PTFE) SEMI-FINISHED PRODUCTS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 263:2008 | SANITARY APPLIANCES - CROSSLINKED CAST ACRYLIC SHEETS FOR BATHS AND SHOWER TRAYS FOR DOMESTIC PURPOSES |
| DIN ISO 9523:2016-05 | TOURING SKI-BOOTS FOR ADULTS - INTERFACE WITH TOURING SKI-BINDINGS - REQUIREMENTS AND TEST METHODS (ISO 9523:2015) |
| DIN EN ISO 7391-2:2006-06 | PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 11403-1:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| DIN EN ISO 11833-1:2012-11 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| I.S. EN ISO 3167:2014 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| I.S. EN ISO 8257-2:2006 | PLASTICS - POLY(METHYL METHACRYLATE) (PMMA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 10245-1:2011 | STEEL WIRE AND WIRE PRODUCTS - ORGANIC COATINGS ON STEEL WIRE - PART 1: GENERAL RULES |
| I.S. EN 131-2:2010 | LADDERS - PART 2: REQUIREMENTS, TESTING, MARKING |
| I.S. EN ISO 15013:2007 | PLASTICS - EXTRUDED SHEETS OF POLYPROPYLENE (PP) - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 14663-2:2006 | PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 15103-2:2007 | PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 14628:2005 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| I.S. EN 1504-5:2013 | PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 5: CONCRETE INJECTION |
| I.S. EN 607:2004 | EAVES GUTTERS AND FITTINGS MADE OF PVC-U - DEFINITIONS, REQUIREMENTS AND TESTING |
| I.S. EN 295-3:2012 | VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 3: TEST METHODS |
| I.S. EN ISO 2898-2:2008 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 11963:2012 | Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:2012) |
| I.S. EN 26:2015 | GAS-FIRED INSTANTANEOUS WATER HEATERS FOR THE PRODUCTION OF DOMESTIC HOT WATER |
| I.S. EN ISO 4894-2:1999 | PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 1873:2014 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| I.S. EN ISO 3673-2:2012 | PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES OF CROSSLINKED EPOXY RESINS (ISO 3673-2:2012) |
| I.S. EN ISO 11542-2:1999 | PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 11963:2013-03 | PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS (ISO 11963:2012) |
| I.S. EN ISO 6259-1:2015 | THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL TEST METHOD (ISO 6259-1:2015) |
| DIN EN ISO 1873-2:2000-12 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN 16972:1995-03 | COMPRESSION MOULDED PLATES MADE OF POLYETHYLENE HIGH DENSITY (PE-UHMW), (PE-HMW), (PE-HD) - TECHNICAL SPECIFICATIONS |
| DIN EN ISO 15526-2:2004-10 | PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN ISO 1874-2:2012 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 1874-2:2012) |
| DIN EN ISO 11439:2013-09 | Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO 11439:2013) |
| DIN ISO 7148-2:2001-03 | PLAIN BEARINGS - TESTING OF THE TRIBOLOGICAL BEHAVIOUR OF BEARING MATERIALS - PART 2: TESTING OF POLYMER-BASED PLAIN BEARING MATERIALS (ISO 7148-2:2012) |
| I.S. EN 295-4:2013 | VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 4: REQUIREMENTS FOR ADAPTORS, CONNECTORS AND FLEXIBLE COUPLINGS |
| DIN EN 858-1:2002-05 | CONTINUOUS HANDLING EQUIPMENT AND SYSTEMS - PART 1: SAFETY AND EMC REQUIREMENTS FOR THE EQUIPMENT FOR THE STORAGE OF BULK MATERIALS IN SILOS, BUNKERS, BINS AND HOPPERS |
| I.S. EN 14427:2014 | LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| I.S. EN 15274:2015 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| I.S. EN 13341:2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| DIN EN 1873:2016-07 | PREFABRICATED ACCESSORIES FOR ROOFING - INDIVIDUAL ROOFLIGHTS OF PLASTICS - PRODUCT SPECIFICATION AND TEST METHODS |
| DIN EN ISO 12215-5:2014-10 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008 + AMD 1:2014) |
| I.S. EN ISO 10366-2:2004 | PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| I.S. EN 13575:2012 | STATIC THERMOPLASTIC TANKS FOR THE ABOVE GROUND STORAGE OF CHEMICALS - BLOW MOULDED OR ROTATIONALLY MOULDED POLYETHYLENE TANKS - REQUIREMENTS AND TEST METHODS |
| I.S. EN 12245:2009 | TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS |
| I.S. EN ISO 7823-3:2007 | PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 3: CONTINUOUS CAST SHEETS |
| I.S. EN ISO 11439:2013 | GAS CYLINDERS - HIGH PRESSURE CYLINDERS FOR THE ON-BOARD STORAGE OF NATURAL GAS AS A FUEL FOR AUTOMOTIVE VEHICLES (ISO 11439:2013) |
| VDE 0349-2:1998-10 | METHOD OF TEST FOR THE HYDROLYTIC STABILITY - MOULDED THERMOSETS |
| VDI 3388:2012-03 | Materials for trimming and forming dies |
| BS 2782-9 Method 910A:1996 | Methods of testing plastics. Sampling and test specimen preparation Injection moulding test specimens of thermoplastic materials |
| VDI 3405 Blatt 1:2013-10 | Additive manufacturing processes, rapid manufacturing - Laser sintering of polymer parts - Quality control |
| NBR ISO 16486-1 : 2013 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS WITH FUSION JOINTING AND MECHANICAL JOINTING - PART 1: GENERAL |
| ASME PCC 2 : 2015 | REPAIR OF PRESSURE EQUIPMENT AND PIPING |
| DIN EN 61234-2:1998-10 | ELECTRICAL INSULATING MATERIALS - METHOD OF TEST FOR THE HYDROLYTIC STABILITY - PART 2: MOULDED THERMOSETS |
| SAE J1639_201703 | Classification System for Automotive Polyamide (PA) Plastics |
| BS EN 4702-03:2017 | Aerospace series. Quick release fastening systems for non-structural and lining applications Stud - quick-release and locking |
| ISO 11515:2013 | Gas cylinders — Refillable composite reinforced tubes of water capacity between 450 L and 3000 L — Design, construction and testing |
| 15/30327856 DC : 0 | BS ISO 20558-2 - PLASTICS - POLY(PHENYLENE SULFIDE) (PPS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES |
| BS EN ISO 25137-2:2017 | Plastics. Sulfone polymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| I.S. EN ISO 2897-2:2004 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 178 : 2010 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| DIN EN ISO 16396-1:2015-05 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015) |
| 97/713393 DC : DRAFT AUG 1997 | PREN 4364 - AEROSPACE STANDARD - CAST (PMMA) ACRYLIC - PROPERTIES |
| 97/713394 DC : DRAFT AUG 1997 | PREN 4365 - AEROSPACE STANDARD - HEAT AND CRAZING RESISTANT ACRYLIC - CAST AND CROSS LINKED - LOW MOISTURE ABSORPTION - PROPERTIES |
| 05/30130524 DC : DRAFT MAR 2005 | ISO 22621-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING UP TO AND INCLUDING 2 MPA (20 BAR) - POLYAMIDE (PA) - PART 1: GENERAL |
| 07/30083514 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED AND SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
| BS EN 15860:2010 | Plastics. Thermoplastic semi-finished products for machining. Requirements and test methods |
| 14/30304062 DC : 0 | BS EN ISO 19069-2 - PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 11/30236286 DC : 0 | BS EN ISO 11963 - PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS |
| DIN EN 1013:2015-03 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 22088-2:2007 | PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 2: CONSTANT TENSILE LOAD METHOD |
| 97/713395 DC : DRAFT AUG 1997 | PREN 4366 - AEROSPACE STANDARD - HEAT AND CRAZING RESISTANT ACRYLIC - CAST, CROSSLINKED AND MULTI-AXIALLY STRETCHED - LOW MOISTURE ABSORPTION - PROPERTIES |
| BS EN 16240:2013 | Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings. Requirements and test methods |
| BS ISO 7148-2:2012 | Plain bearings. Testing of the tribological behaviour of bearing materials Testing of polymer-based bearing materials |
| I.S. EN ISO 22088-3:2007 | PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 3: BENT STRIP METHOD |
| 08/30180847 DC : DRAFT JUNE 2008 | BS EN 10245-5 - STEEL WIRE AND WIRE PRODUCTS - ORGANIC COATINGS ON STEEL WIRE - PART 5: POLYAMIDE COATED WIRE |
| I.S. EN ISO 16101:2004 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING |
| 14/30300568 DC : 0 | BS EN 15274 - GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| BS EN ISO 80369-7:2017 | Small-bore connectors for liquids and gases in healthcare applications Connectors for intravascular or hypodermic applications |
| 14/30283167 DC : 0 | BS ISO 18263-2 - PLASTICS - MIXTURES OF POLYPROPYLENE (PP) AND POLYETHYLENE (PE) RECYCLATE DERIVED FROM PP AND PE USED FOR FLEXIBLE AND RIGID CONSUMENR PACKAGING - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 08/30154948 DC : DRAFT FEB 2008 | BS ISO 21809-4 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 4: POLYETHYLENE COATINGS (2-LAYER PE) |
| 15/30304408 DC : 0 | BS EN ISO 20029-2 - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 12/30266170 DC : 0 | BS EN 15534-1 - COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1 : TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| BS 2782-11.1161A(1998) : 1998 | METHODS OF TESTING PLASTICS - THERMOPLASTICS PIPES, FITTINGS AND VALVES - THERMOPLASTICS PIPES - RESISTANCE TO LIQUID CHEMICALS - CLASSIFICATION - IMMERSION TEST METHOD |
| DIN ISO 7148-2:2014-07 | PLAIN BEARINGS - TESTING OF THE TRIBOLOGICAL BEHAVIOUR OF BEARING MATERIALS - PART 2: TESTING OF POLYMER-BASED PLAIN BEARING MATERIALS (ISO 7148-2:2012) |
| 04/102582 DC : 0 | ISO 15869-1 - GASEOUS HYDROGEN AND HYDROGEN BLENDS - LAND VEHICLE FUEL TANKS - PART 1: GENERAL REQUIREMENTS |
| BS ISO 13781:2017 | Implants for surgery. Homopolymers, copolymers and blends on poly(lactide). In vitro degradation testing |
| 11/30192003 DC : 0 | BS EN ISO 7792-2 - PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 17855-2:2016 | Plastics. Polyethylene (PE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| PREN 16506 : DRAFT 2012 | SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL) |
| 17/30355239 DC : 0 | BS ISO 4586-4 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL, HPDL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 4: CLASSIFICATION AND SPECIFICATIONS FOR COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| DD CLC/TS 50131-2-7-2:2009 | Alarm systems. Intrusion and hold-up systems Intrusion detectors. Glass break detectors (passive) |
| DIN EN ISO 13274:2014-06 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING FOR PACKAGING AND IBCS (ISO 13274:2013 + COR. 1:2014) |
| 14/30278882 DC : 0 | BS EN 60079-7 IEC 60079-7 ED. 5.0 - EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' |
| 13/30240167 DC : 0 | BS ISO 16365-2 - PLASTICS - THERMOPLASTIC POLYURETHANES FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS 2782-3.326F(1997) : 1997 | PLASTICS - DETERMINATION OF TENSILE PROPERTIES - TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES |
| BS EN ISO 15015:2011 | Plastics. Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA). Requirements and test methods |
| INCITS/ISO/IEC 22050 : 2002 | INFORMATION TECHNOLOGY - DATA INTERCHANGE ON 12,7 MM, 384-TRACK MAGNETIC TAPE CARTRIDGES - ULTRIUM-1 FORMAT |
| BS ISO 18263-2:2015 | Plastics. Mixtures of polypropylene (PP) and polyethylene (PE) recyclate derived from PP and PE used for flexible and rigid consumer packaging Preparation of test specimens and determination of properties |
| BS EN ISO 13274:2013 | Packaging. Transport packaging for dangerous goods. Plastics compatibility testing for packaging and IBCs |
| 15/30328314 DC : 0 | BS EN ISO 20557-2 - PLASTICS - POLY(PHENYLENE ETHER) (PPE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMEN AND DETERMINATION OF PROPERTIES |
| ISO 11119-3:2013 | Gas cylinders — Refillable composite gas cylinders and tubes — Design, construction and testing — Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450L with non-load-sharing metallic or non-metallic liners |
| DIN ISO 23013:2016-10 (Draft) | ROAD VEHICLES - DETERMINATION OF RESISTANCE TO FORCED ENTRY OF SECURITY GLASS CONSTRUCTIONS USED IN VEHICLE GLAZING - TEST OF GLAZING SYSTEMS (ISO 23013:2016) |
| 15/30320571 DC : 0 | BS EN 60335-1 ED 5.0 /A2 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 1: GENERAL REQUIREMENTS |
| BS EN ISO 16396-1:2015 | Plastics. Polyamide (PA) moulding and extrusion materials Designation system, marking of products and basis for specifications |
| 01/121538 DC : DRAFT APRIL 2001 | BS EN ISO 899-1 PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP |
| BS ISO 1268-11:2005 | Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| 06/30146370 DC : DRAFT SEP 2006 | ISO 15439-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS FOR MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 4 BAR - POLYAMIDE (PA) - PART 1: GENERAL |
| BS ISO 18872:2007 | Plastics. Determination of tensile properties at high strain rates |
| BS ISO 3672-2 : 2000 AMD 13326 | PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 12/30263853 DC : 0 | BS EN 4702-03 - AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - STUD - QUICK-RELEASE AND LOCKING |
| BS ISO 10366-2 : 94 AMD 10665 | PLASTICS - METHYL METHYLACRYLATE/ACRYLONITRILE/BUTADIENE/STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 14963:2006-12 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods; German version EN 14963:2006 |
| BS ISO 2580-2 : 94 AMD 10660 | PLASTICS - ACRYLONITRILE/BUTADIENE/STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 1163-2 : 1995 AMD 10744 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) MOULDING AND EXTRUSION MATERIALS |
| 08/30165044 DC : DRAFT FEB 2008 | BS ISO 28078-2 - PLASTICS - POLY(PHENYLENE SULFIDE) (PPS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 1013 : 2012 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| 11/30238648 DC : DRAFT FEB 2011 | BS EN 16240 - LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| 08/30180835 DC : DRAFT JUNE 2008 | BS EN 10245-1 - STEEL WIRE AND WIRE PRODUCTS - ORGANIC COATINGS ON STEEL WIRE - PART 1: GENERAL RULES |
| EN 4702-03:2017 | Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 03: Stud - quick-release and locking |
| 08/30180838 DC : DRAFT JUNE 2008 | BS EN 10245-2 - STEEL WIRE AND WIRE PRODUCTS - ORGANIC COATINGS ON STEEL WIRE - PART 2: PVC FINISHED WIRE |
| 04/30122412 DC : DRAFT SEP 2004 | ISO 17194 - STRUCTURAL ADHESIVES - STANDARD DATABASE OF PROPERTIES |
| BS ISO 2898-2 : 1997 AMD 10727 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| PREN 4364 : 200P1 | AEROSPACE SERIES - CAST ACRYLIC - PROPERTIES |
| ISO 20558-2:2018 | Plastics — Poly(phenylene sulfide) (PPS) moulding and extrusion materials — Part 2: Preparation of test specimen and determination of properties |
| NF EN ISO 22088-5 : 2009 | PLASTICS - DETERMINATION OF RESISTANCE TO STRESS CRACKING (ESC) - PART 5: CONSTANT TENSILE DEFORMATION METHOD |
| ISO 7148-2:2012 | Plain bearings — Testing of the tribological behaviour of bearing materials — Part 2: Testing of polymer-based bearing materials |
| ONORM EN ISO 14910-2 : 2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| ISO 12856-1:2014 | Plastics — Plastic railway sleepers for railway applications (railroad ties) — Part 1: Material characteristics |
| ANSI/AAMI/ISO 80369-7:2016 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS |
| I.S. EN 16240:2013 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| BS EN 15502-2-1 : 2012 | GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| I.S. EN ISO 17855-2:2016 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| I.S. EN ISO 15015:2011 | PLASTICS - EXTRUDED SHEETS OF IMPACT-MODIFIED ACRYLONITRILE-STYRENE COPOLYMERS (ABS, AEPDS AND ASA) - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 13628-11:2008 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 11: FLEXIBLE PIPE SYSTEMS FOR SUBSEA AND MARINE APPLICATIONS |
| EN ISO 15527:2013 | Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2010) |
| BS EN ISO 11296-7:2013 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with spirally-wound pipes |
| ISO 4586-6:2015 | High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 6: Classification and specifications for exterior-grade compact laminates of thickness 2 mm and greater |
| PREN 295-4 : DRAFT 2010 | VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 4: REQUIREMENTS FOR ADAPTORS, CONNECTORS AND FLEXIBLE COUPLINGS |
| I.S. EN 50290-2-23:2013 | COMMUNICATION CABLES - PART 2-23: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR MULTI-PAIR CABLES USED IN ACCESS TELECOMMUNICATION NETWORKS: OUTDOOR CABLES |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| SAE J2642_201707 | Recommended Practice for Developing Specifications for Automotive Thermoplastic Materials |
| ASTM D 5857 : 2017 : REDLINE | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
| BS EN ISO 12215-5 : 2008 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION |
| ASTM D 6339 : 2011 | Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS) |
| ASTM D 5936 : 1996 | Specification for Multipurpose Test Specimens (Withdrawn 1998) |
| EN ISO 7391-2:2006 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7391-2:2006) |
| EN ISO 1797:2017 | Dentistry - Shanks for rotary and oscillating instruments (ISO 1797:2017) |
| EN ISO 20029-2:2018 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimen and determination of properties (ISO 20029-2:2017) |
| ISO 17282:2004 | Plastics — Guide to the acquisition and presentation of design data |
| I.S. EN ISO 8986-2:2009 | PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| IEC 62642-2-72:2015 | Alarm systems - Intrusion and hold-up systems - Part 2-72: Intrusion detectors - Glass break detectors (passive) |
| IEC 61241-1-1:1999 | Electrical apparatus for use in the presence of combustible dust - Part 1-1: Electrical apparatus protected by enclosures and surface temperature limitation - Specification for apparatus |
| ISO 17194:2007 | Structural adhesives — A standard database of properties |
| DIN EN ISO 22088-4:2006-11 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 4: Ball or pin impression method (ISO 22088-4:2006) |
| DIN EN 12245:2012-03 | Transportable gas cylinders - Fully wrapped composite cylinders (includes Amendment A1:2011) |
| DIN EN 13566-7:2007-06 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES |
| DIN EN ISO 527-4:1997-07 | Determination of tensile properties of plastics - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites (ISO 527-4:1997) |
| DIN EN ISO 16101:2004-12 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - PLASTICS COMPATIBILITY TESTING |
| DIN EN 295-4:2013-05 | VITRIFIED CLAY PIPE SYSTEMS FOR DRAINS AND SEWERS - PART 4: REQUIREMENTS FOR ADAPTORS, CONNECTORS AND FLEXIBLE COUPLINGS |
| DIN EN ISO 2897-2:2004-05 | PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 6402-2:2004-05 | PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE-(ETHYLENE-PROPYLENE-DIENE)-STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 15346:2015-01 | Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates |
| DIN EN 15342:2008-02 | Plastics - Recycled Plastics - Characterization of polystyrene (PS) recyclates |
| DIN EN 15344:2008-02 | Plastics - Recycled Plastics - Characterisation of Polyethylene (PE) recyclates |
| DIN EN ISO 11403-1:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| ISO 9523:2015 | Touring ski-boots for adults — Interface with touring ski-bindings — Requirements and test methods |
| BS EN ISO 12086-2:2006 | Plastics. Fluoropolymer dispersions and moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 13274:2013 | Packaging — Transport packaging for dangerous goods — Plastics compatibility testing for packaging and IBCs |
| BS EN 1013-5:2000 | Light transmitting profiled plastic sheeting for single skin roofing Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets |
| BS EN 13121-1:2003 | GRP tanks and vessels for use above ground Raw materials. Specification conditions and acceptance conditions |
| BS EN ISO 3673-2:2012 | Plastics. Epoxy resins Preparation of test specimens and determination of properties of crosslinked epoxy resins |
| ISO 17855-2:2016 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| ISO 1163-2:1995 | Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 2898-2:2008 | Plastics — Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| DIN EN ISO 3673-2:2012-10 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012) |
| IEC 60216-2:2005 | Electrical insulating materials - Thermal endurance properties - Part 2: Determination of thermal endurance properties of electrical insulating materials - Choice of test criteria |
| BS EN ISO 11403-1:2014 | Plastics. Acquisition and presentation of comparable multipoint data Mechanical properties |
| EN ISO 14663-2:2006 | Plastics - Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 14663-2:1999) |
| EN 1504-5:2013 | Products and systems for the protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 5: Concrete injection |
| EN ISO 9988-2:2015 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006) |
| EN 16506:2014 | Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL) |
| EN 16240:2013 | Light transmitting flat solid polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods |
| EN 50465:2015 | Gas appliances - Combined heat and power appliance of nominal heat input inferior or equal to 70 kW |
| EN 607:2004 | Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing |
| BS EN ISO 20029-2:2018 | Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| I.S. EN ISO 10350-1:2017 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017) |
| BS ISO 14949:2001 | Implants for surgery. Two-part addition-cure silicone elastomers |
| DIN EN ISO 21003-2:2011-07 | Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes (ISO 21003-2:2008 + Amd 1:2011) (includes Amendment A1:2011) |
| DIN EN 15542:2008-06 | Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods |
| BS ISO 23013:2016 | Road vehicles. Determination of resistance to forced entry of security glass constructions used in vehicle glazing. Test of glazing systems |
| 11/30248330 DC : 0 | BS ISO 17467-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - UNPLASTICIZED POLYAMIDE (PA-U) PIPING SYSTEMS JOINTED BY SOLVENT CEMENT - PART 1: GENERAL |
| I.S. EN ISO 23667:2007 | PACKAGING - TRANSPORT PACKAGING FOR DANGEROUS GOODS - RIGID PLASTICS AND PLASTICS COMPOSITE IBCS - COMPATIBILITY TESTING |
| I.S. EN ISO 6402-2:2004 | PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE - (ETHYLENE-PROPYLENE-DIENE) - STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| NF EN ISO 22088-6 : 2009 | PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 6: SLOW STRAIN RATE METHOD |
| BS EN 124-5:2015 | Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of composite materials |
| 10/30227822 DC : DRAFT DEC 2010 | BS ISO 7148-2 - PLAIN BEARINGS - TESTING OF THE TRIBOLOGICAL BEHAVIOUR OF BEARING MATERIALS - PART 2: TESTING OF POLYMER-BASED BEARING MATERIALS |
| BS ISO 17467-1:2012 | Plastics piping systems for the supply of gaseous fuels. Unplasticized polyamide (PA-U) piping systems jointed by solvent cement General |
| BS ISO 294-5 : 2011 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY |
| I.S. EN ISO 1873-2:2007 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 08/30174001 DC : DRAFT JUNE 2008 | BS ISO 11296-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES |
| 10/30191247 DC : DRAFT APR 2010 | BS EN ISO 13628-16 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 16: SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
| 10/30218935 DC : 0 | BS EN 15502-2-1 - GAS-FIRED HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B[2], B[3] AND B[5] APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| I.S. EN ISO 21809-1:2011 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 1: POLYOLEFIN COATINGS (3-LAYER PE AND 3-LAYER PP) |
| 04/30092689 DC : DRAFT OCT 2004 | ISO 22088-5 - PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 5: CONSTANT TENSILE DEFORMATION METHOD |
| CEI EN 50290-2-23 : 2014 | COMMUNICATION CABLES - PART 2-23: COMMON DESIGN RULES AND CONSTRUCTION - POLYETHYLENE INSULATION FOR MULTI-PAIR CABLES USED IN ACCESS TELECOMMUNICATION NETWORKS: OUTDOOR CABLES |
| S.R. CLC/TS 50131-2-7-2:2009 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 2-7-2: INTRUSION DETECTORS - GLASS BREAK DETECTORS (PASSIVE) |
| BS EN ISO 22088-5:2009 | Plastics. Determination of resistance to environmental stress cracking (ESC) Constant tensile deformation method |
| 12/30264198 DC : 0 | BS EN ISO 11296-7 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES |
| 14/30304003 DC : 0 | BS EN 62899-1 ED.1 - PRINTED ELECTRONICS - MATERIALS - PART 1: SUBSTRATES |
| BS EN 15345:2007 | Plastics. Recycled plastics. Characterization of polypropylene (PP) recyclates |
| ISO 14949:2001 | Implants for surgery — Two-part addition-cure silicone elastomers |
| I.S. EN ISO 22088-4:2007 | PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 4: BALL OR PIN IMPRESSION METHOD |
| 02/709771 DC : DRAFT AUG 2002 | ISO/DIS 9349 - PREINSULATED DUCTILE IRON PIPELINE SYSTEMS |
| I.S. EN ISO 1872-2:2007 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 11040-4:2015 | Prefilled syringes Glass barrels for injectables and sterilized subassembled syringes ready for filling |
| ONORM EN ISO 11833-1 : 2012 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM (ISO 11833-1:2012) |
| BS ISO 15014:2007 | Plastics. Extruded sheets of poly(vinylidene fluoride) (PVDF). Requirements and test methods |
| BS EN 61234-2:1998 | Method of test for hydrolytic stability of electrical insulating materials Moulded thermosets |
| 15/30253325 DC : 0 | BS ISO 17519 - GAS CYLINDERS - REFILLABLE PERMANENTLY MOUNTED COMPOSITE TUBES FOR TRANSPORTATION |
| BS EN ISO 21809-3:2016 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Field joint coatings |
| 11/30242905 DC : 0 | BS EN ISO 3673-2 - PLASTICS - EPOXY RESINS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 08/30180643 DC : DRAFT APRIL 2008 | BS ISO 15869-3 - GASEOUS HYDROGEN AND HYDROGEN BLENDS - LAND VEHICLE FUEL TANKS |
| 13/30273499 DC : 0 | BS ISO 11040-4 - PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING |
| 18/30369393 DC : 0 | BS EN ISO 11296-7 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES |
| 11/30229997 DC : 0 | BS EN 14427 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION |
| I.S. EN ISO 9988-2:2015 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 9988-2:2006) |
| 05/30128281 DC : DRAFT JAN 2005 | ISO 9988-2 - PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DD CLC/TS 50131-2-7-1:2009 | Alarm systems. Intrusion and hold-up systems Intrusion detectors. Glass break detectors (acoustic) |
| BS 7825-3.3:1997 | Calibration of rubber and plastics test equipment. Calibration schedules Mechanical properties of plastics |
| DIN EN ISO 9988-2:2015-05 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 9988-2:2006) |
| BS ISO 14910-2 : 1997 AMD 16024 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 16240:2014-03 | LIGHT TRANSMITTING FLAT SOLID POLYCARBONATE (PC) SHEETS FOR INTERNAL AND EXTERNAL USE IN ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| ISO 16486-1:2012 | Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing — Part 1: General |
| PREN 15274 : DRAFT 2014 | GENERAL PURPOSE ADHESIVES FOR STRUCTURAL ASSEMBLY - REQUIREMENTS AND TEST METHODS |
| 13/30274529 DC : 0 | BS EN ISO 6259-3 - THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 3: POLYOLEFIN PIPES |
| 15/30296854 DC : 0 | BS ISO 13781 - INPLANTS FOR SURGERY - HOMOPOLYMERS, COPOLYMERS AND BLENDS ON POLY(LACTIDE) - IN VITRO DEGRADATION TESTING |
| BS ISO 14663-2 : 1999 AMD 16029 | PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 00/717312 DC : 0 | PREN ISO 12215-5 - SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES, DESIGN STRESSES, SCANTLING DETERMINATION |
| BS ISO 7792-2 : 1997 AMD 15252 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| 03/119348 DC : 0 | PREN 1013-1 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETING FOR INTERNAL AND EXTERNAL ROOFING, WALL CLADDING AND CEILING FINISHES - PART 1: GENERAL REQUIREMENTS AND TEST METHODS |
| 12/30259634 DC : 0 | BS ISO 15399 - GASEOUS HYDROGEN - CYLINDERS AND TUBES FOR STATIONARY STORAGE |
| DD CEN/TS 15534-2:2007 | Wood-plastics composites (WPC) Characterisation of WPC materials |
| 14/30276899 DC : 0 | BS ISO 23013 - ROAD VEHICLES - DETERMINATION TO FORCED ENTRY OF SAFETY GLASS CONSTRUCTIONS USED IN VEHICLE GLAZING - TEST OF GLAZING SYSTEMS |
| DIN EN 15860:2016-07 (Draft) | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 14910-2:2013 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013, CORRECTED VERSION 2015-12-15) |
| 17/30354769 DC : 0 | BS EN ISO 29988-2 - PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ISO 15814:1999 | Implants for surgery — Copolymers and blends based on polylactide — In vitro degradation testing |
| 03/118818 DC : DRAFT DEC 2003 | BS EN ISO 7391-2 - PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| CLC/TS 50131-2-7-2:2009 | Alarm systems - Intrusion and hold-up systems - Part 2-7-2: Intrusion detectors - Glass break detectors (passive) |
| BS EN ISO 19069-2:2016 | Plastics. Polypropylene (PP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| 17/30335677 DC : 0 | BS EN ISO 178 - PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
| ISO 15527:2010 | Plastics — Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) — Requirements and test methods |
| I.S. EN ISO 14632:1999 | EXTRUDED SHEETS OF POLYETHYLENE (PE-HD) - REQUIREMENTS AND TEST METHODS |
| ASTM D 5935 : 1996 | Practice for Acquisition and Presentation of Comparable Single-Point Data (Withdrawn 1998) |
| 07/30169634 DC : 0 | BS ISO 294-5 - PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY |
| BS EN 15542:2008 | Ductile iron pipes, fittings and accessories. External cement mortar coating for pipes. Requirements and test methods |
| I.S. EN 4702-05:2017 | AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 05: RETAINING WASHER |
| DIN EN ISO 15527:2013-05 | PLASTICS - COMPRESSION-MOULDED SHEETS OF POLYETHYLENE (PE-UHMW, PE-HD) - REQUIREMENTS AND TEST METHODS (ISO 15527:2010) |
| DIN EN 124-5:2015-09 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 5: GULLY TOPS AND MANHOLE TOPS MADE OF COMPOSITE MATERIALS |
| I.S. EN ISO 9093-2:2002 | SMALL CRAFT - SEACOCKS AND THROUGH-HULL FITTINGS - PART 2: NON-METALLIC |
| 17/30325386 DC : 0 | BS ISO 18250-1- CONNECTORS FOR RESERVOIR DELIVERY SYSTEMS - PART 1: GENERAL REQUIREMENTS AND COMMON TEST METHODS |
| BS ISO 12086-2 : 2001 AMD 10637 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS |
| 17/30355245 DC : 0 | BS ISO 4586-6 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL, HPDL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 6: CLASSIFICATION AND SPECIFICATIONS FOR EXTERIOR-GRADE COMPACT LAMINATES OF THICKNESS 2 MM AND GREATER |
| API 17J REDLINE : 2008 | SPECIFICATION FOR UNBONDED FLEXIBLE PIPE |
| BS EN ISO 21809-1:2011 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Polyolefin coatings (3-layer PE and 3-layer PP) |
| ISO 20753:2008 | Plastics — Test specimens |
| BS IEC 62899-201 : 2016 | PRINTED ELECTRONICS - PART 201: MATERIALS - SUBSTRATES |
| I.S. EN ISO 21003-2:2008 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 2: PIPES |
| I.S. EN 15860:2010 | PLASTICS - THERMOPLASTIC SEMI-FINISHED PRODUCTS FOR MACHINING - REQUIREMENTS AND TEST METHODS |
| ISO 14910-2:2013 | Plastics — Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion — Part 2: Preparation of test specimens and determination of properties |
| DIN EN ISO 20028-2:2015-08 (Draft) | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
| I.S. EN 1013:2012 | LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS |
| PREN ISO 11833-1 : DRAFT 2010 | PLASTICS - UNPLASTICIZED POLY(VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: SHEETS OF THICKNESS NOT LESS THAN 1 MM |
| IEC 60079-0:2017 | Explosive atmospheres - Part 0: Equipment - General requirements |
| CEI EN 60216-2 : 2006 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
| BS EN ISO 294-5:2017 | Plastics. Injection moulding of test specimens of thermoplastic materials Preparation of standard specimens for investigating anisotropy |
| BS EN ISO 9093-2:2002 | Small craft. Seacocks and through-hull fittings Non-metallic |
| IEC 62642-2-73:2015 | Alarm systems - Intrusion and hold-up systems - Part 2-73: Intrusion detectors - Glass break detectors (active) |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| EN ISO 20753:2014 | Plastics - Test specimens (ISO 20753:2008) |
| I.S. EN ISO 12215-5:2008 | SMALL CRAFT - HULL CONSTRUCTION AND SCANTLINGS - PART 5: DESIGN PRESSURES FOR MONOHULLS, DESIGN STRESSES, SCANTLINGS DETERMINATION (ISO 12215-5:2008) |
| ISO 9093-2:2002 | Small craft — Seacocks and through-hull fittings — Part 2: Non-metallic |
| EN ISO 11296-7:2013 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2011) |
| ISO 7628:2010 | Road vehicles — Thermoplastics tubing for air braking systems |
| ISO 15439-1:2007 | Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) — Polyamide (PA) — Part 1: General |
| ISO 21809-4:2009 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 4: Polyethylene coatings (2-layer PE) |
| IEC 61234-2:1997 | Electrical insulating materials - Methods of test for the hydrolytic stability - Part 2: Moulded thermosets |
| DIN EN 295-3:2012-03 | Vitrified clay pipe systems for drains and sewers - Part 3: Test methods |
| S.R. CEN TS 15534-2:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 2: CHARACTERISATION OF WPC MATERIALS |
| ISO 4586-8:2015 | High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 8: Classification and specifications for alternative core laminates |
| I.S. EN ISO 22088-6:2009 | PLASTICS - DETERMINATION OF RESISTANCE TO ENVIRONMENTAL STRESS CRACKING (ESC) - PART 6: SLOW STRAIN RATE METHOD |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| I.S. EN 15542:2008 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL CEMENT MORTAR COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| DIN EN ISO 7823-1:2003-12 | PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 1: CAST SHEETS |
| DIN EN 607:2005-02 | Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing |
| DIN EN ISO 16103:2005-09 | Packaging - Transport packaging for dangerous goods - Recycled plastics material (ISO 16103:2005) |
| DIN EN ISO 7823-3:2007-08 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2007) |
| DIN EN ISO 11542-2:2010-01 | Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998 + Cor. 1:2007) (includes Corrigendum AC:2008) |
| DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
| DIN EN ISO 7823-2:2003-12 | PLASTICS - POLY(METHYL METHACRYLATE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS - PART 2: EXTRUDED SHEETS |
| BS EN ISO 16101:2004 | Packaging. Transport packaging for dangerous goods. Plastics compatibility testing |
| BS EN ISO 14529-2:2000 | Plastics. Melamine/phenolic powder moulding compounds (MP-PMCs) Preparation of test specimens and determination of properties |
| BS EN ISO 22088-4:2006 | Plastics. Determination of resistance to environmental stress cracking (ESC) Ball or pin impression method |
| ISO 6224:2011 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications — Specification |
| BS EN ISO 1873-2:2007 | Plastics. Polypropylene (PP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 1873-2:2007 | Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 2897-2:2003 | Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN 607:2004 | Eaves gutters and fittings made of PVC-U. Definitions, requirements and testing |
| IEC 60079-0:2017 RLV | Explosive atmospheres - Part 0: Equipment - General requirements |
| ISO 23667:2007 | Packaging — Transport packaging for dangerous goods — Rigid plastics and plastics composite IBCs — Compatibility testing |
| BS EN ISO 13000-2:2005 | Plastics. Polytetrafluoroethylene (PTFE) semi-finished products Preparation of test specimens and determination of properties |
| BS EN 13566-7:2007 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with spirally-wound pipes |
| EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
| ISO 20028-2:2017 | Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 527-4:1997 | Plastics. Determination of tensile properties Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| BS EN 263:2008 | Sanitary appliances. Crosslinked cast acrylic sheets for baths and shower trays for domestic purposes |
| BS EN ISO 3672-2:2001 | Plastics. Unsaturated-polyester resins (UP-R) Preparation of test specimens and determination of properties |
| BS EN 131-2 : 2010 | LADDERS - PART 2: REQUIREMENTS, TESTING, MARKING |
| BS EN ISO 6224:2011 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications. Specification |
| BS EN ISO 1874-1:2001 | Plastics. Polyamide (PA) moulding and extrusion materials Designation |
| BS EN 12566-3 : 2005 | SMALL WASTEWATER TREATMENT SYSTEMS FOR UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| ISO 1874-2:2012 | Plastics — Polyamide (PA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN 13575:2012 | Static thermoplastic tanks for the above ground storage of chemicals. Blow moulded or rotationally moulded polyethylene tanks. Requirements and test methods |
| ISO 22088-6:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 6: Slow strain rate method |
| BS EN 14427:2014 | LPG equipment and accessories. Transportable refillable fully wrapped composite cylinders for LPG. Design and construction |
| ISO 80369-7:2016 | Small-bore connectors for liquids and gases in healthcare applications — Part 7: Connectors for intravascular or hypodermic applications |
| BS EN 13349:2002 | Copper and copper alloys. Pre-insulated copper tubes with solid covering |
| ISO 2580-2:2003 | Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 10366-2:2003 | Plastics. Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 14530-2:1999 | Plastics — Unsaturated-polyester powder moulding compounds (UP-PMCs) — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 7823-2:2003 | Plastics. Poly(methyl methacrylate) sheets. Types, dimensions and characteristics Extruded sheets |
| BS EN 13566-3:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with close fit pipes |
| ISO 8257-2:2001 | Plastics — Poly(methyl methacrylate) (PMMA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 16101:2004 | Packaging — Transport packaging for dangerous goods — Plastics compatibility testing |
| ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
| BS EN ISO 15013:1999 | Extruded sheets of polypropylene (PP). Requirements and test methods |
| ISO 4894-2:1995 | Plastics — Styrene/acrylonitrile (SAN) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 1874-1:2010 | Plastics — Polyamide (PA) moulding and extrusion materials — Part 1: Designation system and basis for specification |
| ISO 14529-2:1999 | Plastics — Melamine/phenolic powder moulding compounds (MP-PMCs) — Part 2: Preparation of test specimens and determination of properties |
| ISO 6259-1:2015 | Thermoplastics pipes — Determination of tensile properties — Part 1: General test method |
| ISO 16396-1:2015 | Plastics — Polyamide (PA) moulding and extrusion materials — Part 1: Designation system, marking of products and basis for specifications |
| ISO 12086-2:2006 | Plastics — Fluoropolymer dispersions and moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 3672-2:2000 | Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties |
| ISO 7823-1:2003 | Plastics — Poly(methyl methacrylate) sheets — Types, dimensions and characteristics — Part 1: Cast sheets |
| ISO 22088-3:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 3: Bent strip method |
| BS EN ISO 14527-2:2000 | Preparation of test specimens and determination of properties |
| ISO 22088-2:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 2: Constant tensile load method |
| ISO 7792-2:2012 | Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 11403-1:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties |
| BS EN 1504-5:2013 | Products and systems for the protection and repair of concrete structures. Definitions, requirements, quality control and evaluation of conformity Concrete injection |
| BS EN ISO 7823-1:2003 | Plastics. Poly(methyl methacrylate) sheets. Types, dimensions and characteristics Cast sheets |
| ISO 16396-2:2017 | Plastics — Polyamide (PA) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 8257-2:2006 | Plastics. Poly(methyl methacrylate) (PMMA) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 483 : 2000 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| ISO 10350:1993 | Plastics — Acquisition and presentation of comparable single-point data |
| ISO 1622-2:1995 | Plastics — Polystyrene (PS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 6259-1:2015 | Thermoplastics pipes. Determination of tensile properties General test method |
| BS EN ISO 22088-3:2006 | Plastics. Determination of resistance to environmental stress cracking (ESC) Bent strip method |
| ISO 6402-2:2003 | Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 11833-1:2012 | Plastics. Unplasticized poly(vinyl chloride) sheets. Types, dimensions and characteristics Sheets of thickness not less than 1 mm |
| 05/30134569 DC : DRAFT JUN 2005 | IEC 60079-0. ED. 5.0 - ELECTRICAL APPARATUS FOR EXPLOSIVE ATMOSPHERES - PART 0: GENERAL REQUIREMENTS |
| ISO 13000-2:2005 | Plastics — Polytetrafluoroethylene (PTFE) semi-finished products — Part 2: Preparation of test specimens and determination of properties |
| BS EN 10245-1:2011 | Steel wire and wire products. Organic coatings on steel wire General rules |
| ISO 11542-2:1998 | Plastics — Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 25137-2:2009 | Plastics — Sulfone polymer moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| ISO 14526-2:1999 | Plastics — Phenolic powder moulding compounds (PF-PMCs) — Part 2: Preparation of test specimens and determination of properties |
| ISO 10366-2:2003 | Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 8986-2:2009 | Plastics — Polybutene-1 (PB-1) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 12086-1:2006 | Plastics — Fluoropolymer dispersions and moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 9988-2:2006 | Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 3673-2:2012 | Plastics — Epoxy resins — Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins |
| BS EN 15342:2007 | Plastics. Recycled plastics. Characterization of polystyrene (PS) recyclates |
| BS EN ISO 6402-2:2003 | Plastics. Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 14663-2:2006 | Plastics. Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 6259-3:2015 | Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes |
| BS EN ISO 2897-2:2003 | Plastics. Impact-resistant polystyrene (PS-I) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 13341 : 2005 | STATIC THERMOPLASTIC TANKS FOR ABOVE GROUND STORAGE OF DOMESTIC HEATING OILS, KEROSENE AND DIESEL FUELS - BLOW MOULDED AND ROTATIONALLY MOULDED POLYETHYLENE TANKS AND ROTATIONALLY MOULDED TANKS MADE OF ANIONICALLY POLYMERIZED POLYAMIDE 6 - REQUIREMENTS AND TEST METHODS |
| BS EN ISO 11439:2013 | Gas cylinders. High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
| ISO 13628-2:2006 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 2: Unbonded flexible pipe systems for subsea and marine applications |
| BS EN ISO 14526-2:2000 | Plastics. Phenolic powder moulding compounds (PF-PMCs) Preparation of test specimens and determination of properties |
| BS EN 4691-1:2017 | Aerospace series. Tie rod with integrated bolts Technical specification |
| ISO 22088-4:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 4: Ball or pin impression method |
| DIN EN 10245-1:2012-01 | STEEL WIRE AND WIRE PRODUCTS - ORGANIC COATINGS ON STEEL WIRE - PART 1: GENERAL RULES |
| EN 15342:2007 | Plastics - Recycled Plastics - Characterization of polystyrene (PS) recyclates |
| EN 295-3:2012 | Vitrified clay pipe systems for drains and sewers - Part 3: Test methods |
| EN 89:2015 | Gas-fired storage water heaters for the production of domestic hot water |
| EN ISO 1874-1:2010 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specification (ISO 1874-1:2010) |
| EN ISO 1163-2:1999 | Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995) |
| EN ISO 2898-2:2008 | Plastics - Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2898-2:2008) |
| EN ISO 15252-2:1999 | Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 15252-2:1999) |
| EN 14628:2005 | Ductile iron pipes, fittings and accessories - External polyethylene coating for pipes - Requirements and test methods |
| EN ISO 8257-2:2006 | Plastics - Poly(methyl methacrylate) (PMMA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8257-2:2001) |
| EN ISO 8986-2:2009 | Plastics - Polybutene-1 (PB-1) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 8986-2:2009) |
| EN ISO 19069-2:2016 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016) |
| EN 14427:2014 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
| EN 14471:2013+A1:2015 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods |
| EN 14963:2006 | Roof coverings - Continuous rooflights of plastics with or without upstands - Classification, requirements and test methods |
| EN ISO 1873-2:2007 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007) |
| EN 13677-2:2003 | Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements |
| EN ISO 1874-2:2012 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| EN ISO 14529-2:1999 | Plastics - Melamine/phenolic powder moulding compounds (MP-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14529-2:1999) |
| EN 15347:2007 | Plastics - Recycled Plastics - Characterisation of plastics wastes |
| EN ISO 15526-2:2004 | Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000) |
| EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| EN ISO 10366-2:2003 | Plastics - Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 10366-2:2003) |
| EN 15345:2007 | Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates |
| EN ISO 6224:2011 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) |
| EN ISO 10350-1:2017 | Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017) |
| EN ISO 21809-1:2011 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2011) |
| EN ISO 22088-4:2006 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 4: Ball or pin impression method (ISO 22088-4:2006) |
| EN ISO 3672-2:2001 | Plastics - Unsaturated-polyester resins (UP-R) - Part 2: Preparation of test specimens and determination of properties (ISO 3672-2:2000) |
| EN ISO 2580-2:2003 | Plastics - Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2580-2:2003) |
| EN ISO 16103:2005 | Packaging - Transport packages for dangerous goods - Recycled plastics material (ISO 16103:2005) |
| EN ISO 16396-2:2017 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| EN ISO 22088-5:2009 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 5: Constant tensile deformation method (ISO 22088-5:2006) |
| EN ISO 15013:2007 | Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007) |
| EN 1873:2014+A1:2016 | Prefabricated accessories for roofing - Individual rooflights of plastics - Product specification and test methods |
| EN ISO 22088-2:2006 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 2: Constant tensile load method (ISO 22088-2:2006) |
| EN 15502-2-1:2012+A1:2016 | Gas-fired central heating boilers - Part 2-1: Specific standard for type C appliances and type B2, B3 and B5 appliances of a nominal heat input not exceeding 1 000 kW |
| EN ISO 6259-3:2015 | Thermoplastics pipes - Determination of tensile properties - Part 3: Polyolefin pipes (ISO 6259-3:2015) |
| EN 26:2015 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| EN ISO 7823-1:2003 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 1: Cast sheets (ISO 7823-1:2003) |
| EN ISO 20028-2:2017 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017) |
| EN ISO 17855-2:2016 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016) |
| EN ISO 1622-2:1999 | Plastics - Polystyrene (PS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1622-2:1995) |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN ISO 4894-2:1999 | Plastics - Styrene/acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 4894-2:1995) |
| EN ISO 1872-2:2007 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1872-2:2007) |
| EN ISO 15103-2:2007 | Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15103-2:2007) |
| EN ISO 14526-2:1999 | Plastics - Phenolic powder moulding compounds (PF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14526-2:1999) |
| EN ISO 3673-2:2012 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012) |
| EN ISO 14910-2:2013 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15) |
| EN 295-4:2013 | Vitrified clay pipe systems for drains and sewers - Part 4: Requirements for adaptors, connectors and flexible couplings |
| EN 12245:2009+A1:2011 | Transportable gas cylinders - Fully wrapped composite cylinders |
| EN 15542:2008 | Ductile iron pipes, fittings and accessories - External cement mortar coating for pipes - Requirements and test methods |
| EN ISO 11833-1:2012 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012) |
| EN 263:2008 | Sanitary appliances - Crosslinked cast acrylic sheets for baths and shower trays for domestic purposes |
| EN ISO 7823-2:2003 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 2: Extruded sheets (ISO 7823-2:2003) |
| EN ISO 16396-1:2015 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015) |
| EN ISO 22088-6:2009 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 6: Slow strain rate method (ISO 22088-6:2006) |
| EN ISO 15015:2011 | Plastics - Extruded sheets of impact-modified acrylonitrile-styrene copolymers (ABS, AEPDS and ASA) - Requirements and test methods (ISO 15015:2011) |
| EN ISO 7792-2:2012 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012) |
| EN ISO 6402-2:2003 | Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003) |
| EN ISO 2897-2:2003 | Plastics - Impact-resistant polystyrene (PS-I) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 2897-2:2003) |
| EN 15346:2014 | Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates |
| EN ISO 14527-2:1999 | Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF-MF-PMCs) - Part 2: Preparation of test specimens and determination of properties (ISO 14527-2:1999) |
| EN ISO 22088-3:2006 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 3: Bent strip method (ISO 22088-3:2006) |
| EN ISO 25137-2:2017 | Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009) |
| DIN EN 15502-2-1:2013-01 | GAS-FIRED CENTRAL HEATING BOILERS - PART 2-1: SPECIFIC STANDARD FOR TYPE C APPLIANCES AND TYPE B2, B3 AND B5 APPLIANCES OF A NOMINAL HEAT INPUT NOT EXCEEDING 1000 KW |
| 12/30263857 DC : 0 | BS EN 4702-05 - AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - WASHER |
| BS EN 14963:2006 | Roof coverings. Continuous rooflights of plastics with or without upstands. Classification, requirements and test methods |
| BS EN 16506:2014 | Systems for renovation of drains and sewers. Lining with a rigidly anchored plastics inner layer (RAPL) |
| ISO 17467-1:2012 | Plastics piping systems for the supply of gaseous fuels — Unplasticized polyamide (PA-U) piping systems jointed by solvent cement — Part 1: General |
| I.S. EN 60079-0:2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011 (MOD)) |
| BS ISO 16365-2:2014 | Plastics. Thermoplastic polyurethanes for moulding and extrusion Preparation of test specimens and determination of properties |
| ISO 21004:2006 | Plastics piping systems — Multilayer pipes and their joints, based on thermoplastics, for water supply |
| BS ISO 21809-4:2009 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Polyethylene coatings (2-layer PE) |
| I.S. EN 13566-7:2007 | PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES |
| I.S. EN ISO 80369-7:2017 COR 2017 | SMALL-BORE CONNECTORS FOR LIQUIDS AND GASES IN HEALTHCARE APPLICATIONS - PART 7: CONNECTORS FOR INTRAVASCULAR OR HYPODERMIC APPLICATIONS (ISO 80369-7:2016, CORRECTED VERSION 2016-12-01) |
| BS ISO 9523:2015 | Touring ski-boots for adults. Interface with touring ski-bindings. Requirements and test methods |
| 14/30300605 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
| I.S. EN ISO 21809-3:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS (ISO 21809-3:2016) |
| ISO 23013:2016 | Road vehicles — Determination of resistance to forced entry of security glass constructions used in vehicle glazing — Test of glazing systems |
| 06/30130317 DC : DRAFT JULY 2006 | ISO 11833-1 - PLASTICS - UNPLASTICIZED POLY (VINYL CHLORIDE) SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS |
| BS ISO 11403-1 : AMD 10683 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - MECHANICAL PROPERTIES |
| 08/30174008 DC : DRAFT JUNE 2008 | BS ISO 11296-4 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACES PIPES |
| 16/30329416 DC : 0 | BS EN 12566-3 - SMALL WASTEWATER TREATMENT SYSTEMS UP TO 50 PT - PART 3: PACKAGED AND/OR SITE ASSEMBLED DOMESTIC WASTEWATER TREATMENT PLANTS |
| BS ISO 7628:2010 | Road vehicles. Thermoplastics tubing for air braking systems |
| 10/30196135 DC : 0 | BS ISO 11515 - GAS CYLINDERS - REFILABLE COMPOSITE REINFORCED TUBES OF WATER CAPACITY BETWEEN 150 L AND 3000 L - DESIGN, CONSTRUCTION AND TESTING |
| ISO 21138-2:2007 | Plastics piping systems for non-pressure underground drainage and sewerage — Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) — Part 2: Pipes and fittings with smooth external surface, Type A |
| DIN EN ISO 17855-2:2016-06 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
| 16/30340635 DC : 0 | BS EN 438-9 - HIGH-PRESSURE DECORATIVE LAMINATES (HPL) - SHEETS BASED ON THERMOSETTING RESINS (USUALLY CALLED LAMINATES) - PART 9: CLASSIFICATION AND SPECIFICATIONS FOR ALTERNATIVE CORE LAMINATES |
| BS ISO 9988-2 : 2006 | PLASTICS - POLYOXYMETHYLENE (POM) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 80369-7:2017 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
| EN ISO 14632:1998 | Extruded sheets of polyethylene (PE-HD) - Requirements and test methods (ISO 14632:1998) |
| I.S. EN ISO 25137-2:2017 | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| 13/30271610 DC : 0 | BS ISO 17296-3 - ADDITIVE MANUFACTURING - RAPID TECHNOLOGIES (RAPID PROTOTYPING) - PART 3: TEST METHODS |
| BS EN ISO 21003-2 : 2008 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 2: PIPES |
| BS ISO 1622-2 : 1995 AMD 10649 | PLASTICS - POLYSTYRENE (PS) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| ASTM D 5138 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| DIN ISO 11040-4:2007-10 | PREFILLED SYRINGES - PART 4: GLASS BARRELS FOR INJECTABLES AND STERILIZED SUBASSEMBLED SYRINGES READY FOR FILLING (ISO 11040-4:2015) |
| BS EN ISO 6259-3:2015 | Thermoplastics pipes. Determination of tensile properties Polyolefin pipes |
| I.S. EN 15344:2007 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLYETHYLENE (PE) RECYCLATES |
| BS ISO 12086-1 : 1995 AMD 10638 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
| BS ISO 11515 : 2013 | GAS CYLINDERS - REFILLABLE COMPOSITE REINFORCED TUBES OF WATER CAPACITY BETWEEN 450 L AND 3000 L - DESIGN, CONSTRUCTION AND TESTING |
| 15/30291323 DC : 0 | BS EN ISO 1797 - DENTISTRY - SHANKS FOR ROTARY, OSCILLATING AND RECIPROCATING INSTRUMENTS |
| DIN EN ISO 22088-6:2009-10 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 6: Slow strain rate method (ISO 22088-6:2006) |
| 08/30171587 DC : DRAFT MAY 2008 | BS ISO 7628 - ROAD VEHICLES - THERMOPLASTICS TUBING FOR AIR BRAKING SYSTEMS |
| BS ISO 1268-8:2004 | Fibre-reinforced plastics. Methods of producing test plates Compression moulding of SMC and BMC |
| 15/30304402 DC : 0 | BS EN ISO 20028-2 - PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN ISO 1797:2017 | Dentistry. Shanks for rotary and oscillating instruments |
| ISO 11040-4:2015 | Prefilled syringes — Part 4: Glass barrels for injectables and sterilized subassembled syringes ready for filling |
| PREN 15346 : DRAFT 2013 | PLASTICS - RECYCLED PLASTICS - CHARACTERISATION OF POLY(VINYL CHLORIDE) (PVC) RECYCLATES |
| ISO 13781:2017 | Implants for surgery — Homopolymers, copolymers and blends on poly(lactide) — In vitro degradation testing |
| BS ISO 13628-11:2007 | Petroleum and natural gas industries. Design and operation of subsea production systems Flexible pipe systems for subsea and marine applications |
| API 17B REDLINE : 2008 | RECOMMENDED PRACTICE FOR FLEXIBLE PIPE |
| 04/30091870 DC : DRAFT FEB 2004 | BS EN ISO 12086-2 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS ISO 9349:2017 | Ductile iron pipes, fittings, accessories and their joints. Thermal preinsulated products |
| EN ISO 7823-3:2007 | Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 3: Continuous cast sheets (ISO 7823-3:2007) |
| BS ISO 11833-1:1998 | Plastics. Unplasticized poly(vinyl chloride) sheets. Tapes, dimensions and characteristics Sheets of thickness not less than 1 mm |
| EN 4691-1:2017 | Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification |
| BS EN ISO 9988-2:2015 | Plastics. Polyoxymethylene (POM) moulding and extrusion materials Preparation of test specimens and determination of properties |
| API 17L1 : 2013 | SPECIFICATION FOR FLEXIBLE PIPE ANCILLARY EQUIPMENT |
| PREN ISO 11963 : DRAFT 2011 | PLASTICS - POLYCARBONATE SHEETS - TYPES, DIMENSIONS AND CHARACTERISTICS |
| I.S. EN 60079-7:2015 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' |
| ISO 1797:2017 | Dentistry — Shanks for rotary and oscillating instruments |
| I.S. EN 4691-1:2017 | AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION |
| ISO 9349:2017 | Ductile iron pipes, fittings, accessories and their joints — Thermal preinsulated products |
| ISO/TS 18226:2006 | Plastics pipes and fittings — Reinforced thermoplastics pipe systems for the supply of gaseous fuels for pressures up to 4 MPa (40 bar) |
| I.S. EN 15534-1:2014 | COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS |
| S.R. CEN TS 15534-1:2007 | WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS |
| CLC/TS 50131-2-7-3:2009 | Alarm systems - Intrusion and hold-up systems - Part 2-7-3: Intrusion detectors - Glass break detectors (active) |
| I.S. EN 60216-2:2005 | ELECTRICAL INSULATING MATERIALS - THERMAL ENDURANCE PROPERTIES - PART 2: DETERMINATION OF THERMAL ENDURANCE PROPERTIES OF ELECTRICAL INSULATING MATERIALS - CHOICE OF TEST CRITERIA |
| I.S. EN ISO 16396-1:2015 | PLASTICS - POLYAMIDE (PA) MOULDING AND EXTRUSION MATERIALS - PART 1: DESIGNATION SYSTEM, MARKING OF PRODUCTS AND BASIS FOR SPECIFICATIONS (ISO 16396-1:2015) |
| BS ISO 15527 : 2010 | PLASTICS - COMPRESSION-MOULDED SHEETS OF POLYETHYLENE (PE-UHMW, PE-HD) - REQUIREMENTS AND TEST METHODS |
| EN ISO 294-5:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy (ISO 294-5:2017) |
| BS EN 60079-0 : 2012 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS |
| BS EN ISO 10350-1:2017 | Plastics. Acquisition and presentation of comparable single-point data Moulding materials |
| ASTM D 5937 : 1996 | Standard Test Method for Determination of Tensile Properties and Test Conditions for Moulding and Extrusion Plastics (Withdrawn 1998) |
| EN ISO 13000-2:2005 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005) |
| ISO 7391-2:2006 | Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| EN 15860:2010 | Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods |
| DIN EN ISO 25137-2:2016-08 (Draft) | PLASTICS - SULFONE POLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 25137-2:2009) |
| ISO 21809-1:2011 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) |
| ISO 6691:2000 | Thermoplastic polymers for plain bearings — Classification and designation |
| ISO 294-5:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy |
| ISO 4586-4:2015 | High-pressure decorative laminates (HPL, HPDL) — Sheets based on thermosetting resins (Usually called Laminates) — Part 4: Classification and specifications for compact laminates of thickness 2 mm and greater |
| DIN EN 13575:2012-06 | Static thermoplastic tanks for the above ground storage of chemicals - Blow moulded or rotationally moulded polyethylene tanks - Requirements and test methods |
| DIN EN ISO 7792-2:2013-03 | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 7792-2:2012) |
| DIN EN ISO 10366-2:2004-05 | PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 1504-5:2013-06 | PRODUCTS AND SYSTEMS FOR THE PROTECTION AND REPAIR OF CONCRETE STRUCTURES - DEFINITIONS, REQUIREMENTS, QUALITY CONTROL AND EVALUATION OF CONFORMITY - PART 5: CONCRETE INJECTION |
| BS EN ISO 8986-2:2009 | Plastics. Polybutene-1 (PB-1) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN 13199-3:2000 | Packaging. Small load carrier systems Bond Stackable System (BSS) |
| BS EN ISO 15103-2:2007 | Plastics. Poly(phenylene ether) (PPE) moulding and extrusion materials Preparation of test specimens and determination of properties |
| BS EN ISO 14910-2:2013 | Plastics. Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion Preparation of test specimens and determination of properties |
| BS EN 15274:2015 | General purpose adhesives for structural assembly. Requirements and test methods |
| BS EN 13200-4:2006 | Spectator facilities Seats. Product characteristics |
| BS EN ISO 2898-2:2008 | Plastics. Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials Preparation of test specimens and determination of properties (ISO 2898-2:2008) |
| ISO 15252-2:1999 | Plastics — Epoxy powder moulding compounds (EP-PMCs) — Part 2: Preparation of test specimens and determination of properties |
| ISO 16103:2005 | Packaging — Transport packaging for dangerous goods — Recycled plastics material |
| BS EN ISO 1163-2:2000 | Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 1872-2:2007 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 11439:2013 | Gas cylinders — High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles |
| BS EN 1825-1:2004 | Grease separators Principles of design, performance and testing, marking and quality control |
| BS EN ISO 11963:2012 | Plastics. Polycarbonate sheets. Types, dimensions and characteristics |
| ISO 14663-2:1999 | Plastics — Ethylene/vinyl alcohol (EVOH) copolymer moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 14631:1999 | Extruded sheets of impact-modified polystyrene (PS-I). Requirements and test methods |
| BS EN ISO 22088-2:2006 | Plastics. Determination of resistance to environmental stress cracking (ESC) Constant tensile load method |
| ISO 14527-2:1999 | Plastics — Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) — Part 2: Preparation of test specimens and determination of properties |
| BS EN ISO 7391-2:2006 | Plastics. Polycarbonate (PC) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 22088-5:2006 | Plastics — Determination of resistance to environmental stress cracking (ESC) — Part 5: Constant tensile deformation method |
| BS EN ISO 7792-2:2012 | Plastics. Thermoplastic polyester (TP) moulding and extrusion materials Preparation of test specimens and determination of properties |
| ISO 15526-2:2000 | Plastics — Polyketone (PK) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| BS EN 15344:2007 | Plastics. Recycled plastics. Characterization of polyethylene (PE) recyclates |
| BS EN 15346:2014 | Plastics. Recycled plastics. Characterization of poly(vinyl chloride) (PVC) recyclates |
| BS EN 858-1:2002 | Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control |
| BS EN ISO 14530-2:2000 | Plastics. Unsaturated-polyester powder moulding compounds (UP-PMCs) Preparation of test specimens and determination of properties |
| BS EN ISO 15252-2:2000 | Plastics. Epoxy powder moulding compounds (EP-PMCs) Preparation of test specimens and determination of properties |
| ISO 15013:2007 | Plastics — Extruded sheets of polypropylene (PP) — Requirements and test methods |
| EN 60079-0:2012/A11:2013 | EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED) |
| DIN EN ISO 80369-7:2017-10 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
| DIN EN ISO 2898-2:2009-03 | PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 16101:2004 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing (ISO 16101:2004) |
| EN 13566-4:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes |
| I.S. EN ISO 527-4:1997 | PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES |
| DIN EN ISO 14663-2:2006-06 | PLASTICS - ETHYLENE/VINYL ALCOHOL (EVOH) COPOLYMER MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 1013-5:2000 | Light transmitting profiled plastic sheeting for single skin roofing - Part 5: Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets |
| DIN EN ISO 12086-2:2006-05 | PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN ISO 13000-2:2006-02 | Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2005) |
| DIN EN ISO 14910-2:2013-06 | PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 14910-2:2013) |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| EN 131-2:2010+A2:2017 | Ladders - Part 2: Requirements, testing, marking |
| EN 13200-4:2006 | Spectator facilities - Part 4: Seats - Product characteristics |
| EN 50290-2-23:2013 | Communication cables - Part 2-23: Common design rules and construction - Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables |
| DIN EN 263:2008-06 | Sanitary appliances - Crosslinked cast acrylic sheets for baths and shower trays for domestic purposes |
| DIN EN ISO 15013:2008-01 | Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2007); German version EN ISO 15013:2007 |
| DIN ISO 11040-4:2017-07 | Prefilled syringes - Part 4: Glass barrels for injectables and sterilized subassembled syringes ready for filling (ISO 11040-4:2015) |
| DIN EN ISO 8986-2:2010-04 | PLASTICS - POLYBUTENE-1 (PB-1) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| DIN EN 483:2000-06 | GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW |
| DIN EN 1825-1:2004-12 | Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004 |
| CEN/TS 15534-2:2007 | Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials |
| DIN EN ISO 6224:2012-02 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) |
| EN 13566-7:2007 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes |
| EN 13566-3:2002 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes |
| DIN EN ISO 11403-1:2003-09 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 1: MECHANICAL PROPERTIES (ISO 11403-1:2014) |
| DIN EN 10288:2003-12 | STEEL TUBES AND FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - EXTERNAL TWO-LAYER EXTRUDED POLYETHYLENE BASED COATINGS |
| DIN EN 14628:2006-01 | DUCTILE IRON PIPES, FITTINGS AND ACCESSORIES - EXTERNAL POLYETHYLENE COATING FOR PIPES - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 178:2019 | Plastics - Determination of flexural properties (ISO 178:2019) |
| API RP 17B:2014(R2021) | Recommended Practice for Flexible Pipe, Fifth Edition |
| I.S. EN ISO 527-3:2018 | Plastics - Determination of tensile properties - Part 3: Test conditions for films and sheets (ISO 527-3:2018) |
| I.S. EN 1825-1:2004 | GREASE SEPARATORS - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
| I.S. EN 858-1:2002 | SEPARATOR SYSTEMS FOR LIGHT LIQUIDS (E.G. OIL AND PETROL) - PART 1: PRINCIPLES OF PRODUCT DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL |
| UNE-EN ISO 22088-5:2010 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 5: Constant tensile deformation method (ISO 22088-5:2006) |
| UNE-EN 89:2016 | Gas-fired storage water heaters for the production of domestic hot water |
| UNE-ISO 1268-11:2012 | Fibre-reinforced plastics. Methods of producing test plates. Part 11: Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| UNE-EN ISO 11296-7:2014 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2011) |
| UNE-EN 1013:2013 | Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods |
| UNE-EN ISO 22088-6:2010 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 6: Slow strain rate method (ISO 22088-6:2006) |
| UNE-EN ISO 21809-1:2019 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2018) |
| UNE-EN ISO 17855-2:2016 | Plastics - Polyethylene (PE) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 17855-2:2016) |
| UNE-EN 16506:2015 | Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL) |
| UNE-EN ISO 294-5:2018 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 5: Preparation of standard specimens for investigating anisotropy (ISO 294-5:2017) |
| UNE-EN ISO 11439:2013 | Gas cylinders - High pressure cylinders for the on-board storage of natural gas as a fuel for automotive vehicles (ISO/FDIS 11439:2013) |
| UNE-EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
| UNE-EN ISO 16396-2:2017 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
| UNE-EN 124-5:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 5: Gully tops and manhole tops made of composite materials |
| UNE-EN ISO 9988-2:2015 | Plastics - Polyoxymethylene (POM) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 9988-2:2006) |
| UNE-EN ISO 11296-4:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes (ISO 11296-4:2009, corrected version 2010-06-01) |
| UNE-EN ISO 25137-2:2017 | Plastics - Sulfone polymer moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 25137-2:2009) |
| UNE-EN 50290-2-23:2014 | Communication cables - Part 2-23: Common design rules and construction - Polyethylene insulation for multi-pair cables used in access telecommunication networks: Outdoor cables |
| UNE-EN 12245:2009 | Transportable gas cylinders - Fully wrapped composite cylinders |
| UNE-EN 13575:2012 | Static thermoplastic tanks for the above ground storage of chemicals — Blow moulded or rotationally moulded polyethylene tanks — Requirements and test methods |
| UNE-EN 12566-3:2017 | Small wastewater treatment systems for up to 50 PT - Part 3: Packaged and/or site assembled domestic wastewater treatment plants |
| UNE-EN 10245-1:2012 | Steel wire and wire products - Organic coatings on steel wire - Part 1: General rules |
| UNE-EN 15274:2015 | General purpose adhesives for structural assembly - Requirements and test methods |
| UNE-EN ISO 13274:2014 | Packaging - Transport packaging for dangerous goods - Plastics compatibility testing for packaging and IBCs (ISO 13274:2013) |
| UNE-EN 60079-7:2016 | Explosive atmospheres - Part 7: Equipment protection by increased safety "e" |
| UNE-EN ISO 3673-2:2013 | Plastics - Epoxy resins - Part 2: Preparation of test specimens and determination of properties of crosslinked epoxy resins (ISO 3673-2:2012) |
| UNE-EN ISO 20028-2:2017 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 20028-2:2017) |
| UNE-EN 50131-2-8:2017 | Alarm systems - Intrusion and hold-up systems - Part 2-8: Intrusion detectors - Shock detectors |
| UNE-EN 295-4:2013 | Vitrified clay pipe systems for drains and sewers - Part 4: Requirements for adaptors, connectors and flexible couplings |
| UNE-EN ISO 16396-1:2015 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015) |
| UNE-EN ISO 1874-1:2011 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system and basis for specification (ISO 1874-1:2010) |
| UNE-EN ISO 19069-2:2016 | Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016) |
| I.S. EN 15342:2007 | PLASTICS - RECYCLED PLASTICS - CHARACTERIZATION OF POLYSTYRENE (PS) RECYCLATES |
| UNE-EN ISO 11403-1:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
| UNE-EN ISO 11296-3:2011 | Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3: Lining with close-fit pipes (ISO 11296-3:2009+Cor 1:2011) |
| UNE-EN ISO 11963:2013 | Plastics - Polycarbonate sheets - Types, dimensions and characteristics (ISO 11963:2012) |
| UNE-EN 15860:2011 | Plastics - Thermoplastic semi-finished products for machining - Requirements and test methods |
| UNE-EN ISO 21809-1:2011 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) (ISO 21809-1:2011) |
| UNE-EN ISO 11833-1:2012 | Plastics - Unplasticized poly(vinyl chloride) sheets - Types, dimensions and characteristics - Part 1: Sheets of thickness not less than 1 mm (ISO 11833-1:2012) |
| UNE-EN 15346:2015 | Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates |
| UNE-EN ISO 1874-2:2013 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1874-2:2012) |
| UNE-EN ISO 14910-2:2014 | Plastics - Thermoplastic polyester/ester and polyether/ester elastomers for moulding and extrusion - Part 2: Preparation of test specimens and determination of properties (ISO 14910-2:2013, Corrected version 2015-12-15) |
| UNE-EN 26:2016 | Gas-fired instantaneous water heaters for the production of domestic hot water |
| UNE-EN ISO 20753:2015 | Plastics - Test specimens (ISO 20753:2008) |
| UNE-EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| UNE-EN 1873:2015 | Prefabricated accessories for roofing - Individual rooflights of plastics - Product specification and test methods |
| UNE-EN ISO 6259-3:2015 | Thermoplastics pipes - Determination of tensile properties - Part 3: Polyolefin pipes (ISO 6259-3:2015) |
| UNE-EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| UNE-EN ISO 15527:2014 | Plastics - Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) - Requirements and test methods (ISO 15527:2010) |
| UNE-EN ISO 7792-2:2013 | Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 7792-2:2012) |
| UNE-EN ISO 80369-7:2017 | Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications (ISO 80369-7:2016, Corrected version 2016-12-01) |
| UNE-EN ISO 6224:2012 | Thermoplastics hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 6224:2011) |
| UNE-EN ISO 12215-5:2008 | Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2008) |
| UNE-EN 14427:2014 | LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction |
| NACE SP0304:2023 | Design, Installation and Operation of Thermoplastic Liners for Oilfield Pipelines |
| BS 7008-1(1994) : AMD 8821 | ACQUISITION AND PRESENTATION OF COMPARABLE DATA FOR BASIC PROPERTIES OF PLASTICS - METHOD FOR SINGLE POINT DATA |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics — Multipurpose test specimens |
| AS ISO/ASTM 52921:2020 | Standard terminology for additive manufacturing - Coordinate systems and test methodologies |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 1926:2009 | Rigid cellular plastics — Determination of tensile properties |
| ISO 294-2:1996 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| AS 3996:2019 | Access covers and grates |
| ISO 20753:2008 | Plastics — Test specimens |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.