ISO 7919-4:2009
Withdrawn
Withdrawn
View Superseded by
Mechanical vibration — Evaluation of machine vibration by measurements on rotating shafts — Part 4: Gas turbine sets with fluid-film bearings
Amended by
Available format(s)
Hardcopy , PDF
Published date
09-30-2009
Withdrawn date
04-09-2025
Superseded by
US$96.00
Excluding Tax where applicable
ISO 7919-4:2009 establishes provisions for evaluating the severity of in-situ, broad-band shaft vibration measured radial (i.e. transverse) to the shaft axis at, or close to, the main bearings. These are in terms of
- vibration under normal steady-state operating conditions;
- vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes;
- changes in vibration which can occur during normal steady-state operation.
ISO 7919-4:2009 is applicable to heavy-duty gas turbine sets used in electrical and mechanical drive applications, with fluid-film bearings, outputs greater than 3 MW and an operating speed range under load between 3 000 r/min and 30 000 r/min. This includes gas turbines coupled to other rotating machinery either directly or through a gearbox. In some cases, ISO 7919-4:2009 is not applicable to the evaluation of the vibration of the coupled equipment.
| Committee |
ISO/TC 108/SC 2
|
| DevelopmentNote |
Supersedes ISO/DIS 7919-4. (10/2009)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NEN ISO 7919-4 : 2009 AMD 1 2017 | Identical |
| BIS IS/ISO 7919-4 : 2009 | Identical |
| BS ISO 7919-4 : 2009 | Identical |
| SAC GB/T 11348.4 : 1999 | Identical |
| NF ISO 7919-4 : 2010 AMD 1 2017 | Identical |
| DIN ISO 7919-4:2010-06 | Identical |
| BIS IS 14773-4 : 2000(R2005) | Identical |
| GOST R ISO 7919-4 : 1999 | Identical |
| GOST ISO 7919-4 : 2002 | Identical |
| BS 7508:1995 | Mechanical vibration. Methods and criteria for the mechanical balancing of flexible rotors |
| BS ISO 3977-3:2004 | Gas turbines. Procurement Design requirements |
| ISO 10817-1:1998 | Rotating shaft vibration measuring systems — Part 1: Relative and absolute sensing of radial vibration |
| 09/30192810 DC : DRAFT JAN 2009 | BS ISO 10816-2 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN |
| API 616 REDLINE : 2011 | GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES |
| BS ISO 10816-4 : 2009 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS |
| ISO 3977-3:2004 | Gas turbines — Procurement — Part 3: Design requirements |
| ISO 20816-2:2017 | Mechanical vibration — Measurement and evaluation of machine vibration — Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| BS ISO 21940-31:2013 | Mechanical vibration. Rotor balancing Susceptibility and sensitivity of machines to unbalance |
| 17/30341578 DC : DRAFT MAY 2017 | BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES |
| BS ISO 20816-1:2016 | Mechanical vibration. Measurement and evaluation of machine vibration General guidelines |
| NF ISO 3977-3 : 2005 | GAS TURBINES - PROCUREMENT - PART 3: DESIGN REQUIREMENTS |
| ISO 10816-2:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| ISO 19859:2016 | Gas turbine applications — Requirements for power generation |
| VDI 3840:2004-05 | Vibration analysis for machine sets |
| VDI 3840:2004-05 | VIBRATION ANALYSIS FOR MACHINE SETS |
| BS 3863:1992 | Guide for gas turbines procurement |
| VDI 3839 Blatt 1:2001-03 | Instructions on measuring and interpreting the vibrations of machines - General principles |
| BS 7854-1(1996) : 1996 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - GENERAL GUIDELINES |
| ISO 21940-31:2013 | Mechanical vibration — Rotor balancing — Part 31: Susceptibility and sensitivity of machines to unbalance |
| 00/702358 DC : DRAFT JAN 2000 | ISO/DIS 13380 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - USE OF PERFORMANCE PARAMETERS - GENERAL GUIDELINES |
| BS ISO 20816-2:2017 | Mechanical vibration. Measurement and evaluation of machine vibration Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| DIN ISO 17359:2011-09 | CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES |
| 09/30192807 DC : DRAFT FEB 2009 | BS ISO 7919-2 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN |
| 12/30265145 DC : 0 | BS ISO 21940-31 - MECHANICAL VIBRATION - ROTOR BALANCING - PART 31: SUSCEPTIBILITY AND SENSITIVITY OF MACHINES TO UNBALANCE |
| PD ISO/TR 19201:2013 | Mechanical vibration. Methodology for selecting appropriate machinery vibration standards |
| BS 7854-4:1998 | Mechanical vibration. Evaluation of machine vibration by measurements on non-rotating parts Gas turbine driven sets excluding aircraft derivatives |
| DIN ISO 20816-1:2015-12 (Draft) | MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 1: GENERAL GUIDELINES (ISO 20816-1:2016) |
| 16/30337263 DC : 0 | BS ISO 20816-2 - MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 2: LAND-BASED GAS TURBINES, STEAM TURBINES AND GENERATORS IN EXCESS OF 40 MW, WITH FLUID-FILM BEARINGS |
| BS ISO 13373-1:2002 | Condition monitoring and diagnostics of machines. Vibration condition monitoring General procedures |
| 10/30200372 DC : 0 | BS ISO 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES |
| BS ISO 14839-2:2004 | Mechanical vibration. Vibration of rotating machinery equipped with active magnetic bearings Evaluation of vibration |
| 09/30190941 DC : DRAFT JAN 2009 | BS ISO 10816-4 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS |
| 15/30328956 DC : 0 | BS ISO 20816-1 - MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 1: GENERAL GUIDELINES |
| 16/30341596 DC : 0 | BS ISO 10816-4 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS |
| 09/30197816 DC : 0 | BS ISO 10816-1/AMD1 - MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 1: GENERAL GUIDELINES |
| IEEE 115-2009 REDLINE | IEEE Guide for Test Procedures for Synchronous Machines Part I—Acceptance and Performance Testing Part II—Test Procedures and Parameter Determination for Dynamic Analysis |
| NF ISO 10816-4 : 2010 AMD 1 2017 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS |
| BS ISO 19859:2016 | Gas turbine applications. Requirements for power generation |
| 01/714317 DC : DRAFT OCT 2001 | ISO 18436-2 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - ACCREDITATION OF ORGANIZATIONS AND TRAINING AND CERTIFICATION OF PERSONNEL - PART 2: VIBRATION ANALYSIS |
| 01/708610 DC : DRAFT JUNE 2001 | ISO/DIS 17359 - CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES |
| BS ISO 10817-1:1999 | Rotating shaft vibration measuring systems Relative and absolute sensing of radial vibration |
| BS ISO 10816-2:2009 | Mechanical vibration. Evaluation of machine vibration by measurements on non-rotating parts Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1500 r/min, 1800 r/min, 3000 r/min and 3600 r/min |
| BS ISO 10816-1 : 1995 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 1: GENERAL GUIDELINES |
| BS ISO 7919-1:1996 | Mechanical vibration of non-reciprocating machines. Measurements on rotating shafts and evaluation criteria General guidelines |
| 03/303213 DC : DRAFT FEB 2003 | ISO 14839-2 - MECHANICAL VIBRATION - VIBRATION OF ROTATING MACHINERY EQUIPPED WITH ACTIVE MAGNETIC BEARINGS - PART 2: EVALUATION OF VIBRATION |
| API 616 : 2011 | GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES |
| ISO 10816-1:1995 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 1: General guidelines |
| ISO/TR 19201:2013 | Mechanical vibration — Methodology for selecting appropriate machinery vibration standards |
| ISO 14839-2:2004 | Mechanical vibration — Vibration of rotating machinery equipped with active magnetic bearings — Part 2: Evaluation of vibration |
| ISO 10816-4:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 4: Gas turbine sets with fluid-film bearings |
| ISO 13373-1:2002 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures |
| 14/30244780 DC : 0 | BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION |
| DIN ISO 10816-1:1997-08 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 1: GENERAL GUIDELINES |
| DIN ISO 10816-2:2010-06 | MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN |
| ANSI/ASA S2.80 Part 1:2019 | Mechanical vibration – Measurement and evaluation of machine vibration – Part 1: General guidelines (a nationally adopted international standard amendment) |
| ANSI/ASA S2.80 Part 2:2019 | Mechanical vibration — Measurement and evaluation of machine vibration — Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min (a nationally adopted international standard) |
| ASA S2.80-2019/PART 2/ ISO 20816-2:2017 (R2024) | Mechanical vibration — Measurement and evaluation of machine vibration — Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| ISO 10816-4:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 4: Gas turbine sets with fluid-film bearings |
| ISO 13373-1:2002 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures |
| ISO 13373-3:2015 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 3: Guidelines for vibration diagnosis |
| ISO 21940-12:2016 | Mechanical vibration — Rotor balancing — Part 12: Procedures and tolerances for rotors with flexible behaviour |
| ISO 13373-2:2016 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 2: Processing, analysis and presentation of vibration data |
| ISO 20816-2:2017 | Mechanical vibration — Measurement and evaluation of machine vibration — Part 2: Land-based gas turbines, steam turbines and generators in excess of 40 MW, with fluid-film bearings and rated speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min |
| ISO 2041:2009 | Mechanical vibration, shock and condition monitoring — Vocabulary |
| ISO 10817-1:1998 | Rotating shaft vibration measuring systems — Part 1: Relative and absolute sensing of radial vibration |
| ISO 3977-3:2004 | Gas turbines — Procurement — Part 3: Design requirements |
| ISO 7919-3:2009 | Mechanical vibration — Evaluation of machine vibration by measurements on rotating shafts — Part 3: Coupled industrial machines |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.