ISO 8062-3:2007
Withdrawn
Withdrawn
View Superseded by
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings
Amended by
Available format(s)
Hardcopy , PDF
Published date
05-31-2007
Withdrawn date
04-09-2025
Superseded by
US$96.00
Excluding Tax where applicable
ISO 8062-3:2007 specifies general dimensional and geometrical tolerances, as well as machining allowance grades, for castings as delivered to the purchaser in accordance with ISO 8062-2. It is applicable for the tolerancing of dimensions and geometry, and required machining allowance of castings in all cast metals and their alloys produced by various casting manufacturing processes.
ISO 8062-3:2007 applies to both general dimensional and general geometrical tolerances, unless otherwise specified.
The dimensional tolerances covered by ISO 8062-3:2007 are tolerances for linear dimensions.
The geometrical tolerances covered by ISO 8062-3:2007 are:
- tolerances for straightness,
- flatness,
- roundness,
- parallelism,
- perpendicularity,
- symmetry, and
- coaxiality.
ISO 8062-3:2007 can be used for the selection of tolerance values for individual indications.
| Committee |
ISO/TC 213
|
| DevelopmentNote |
Supersedes ISO/DIS 8062-3 and ISO 8062. (06/2007)
|
| DocumentType |
Standard
|
| Pages |
30
|
| ProductNote |
THIS STANDARD ALSO REFER-ISO 14405
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DS EN ISO 8062-3 : 2007 COR 2009 | Identical |
| DS/EN ISO 8062-3:2007 | Identical |
| DIN EN ISO 8062-3:2008-09 | Identical |
| NF EN ISO 8062-3 : 2007 | Identical |
| NBN EN ISO 8062-3 : 2007 COR 2009 | Identical |
| NEN EN ISO 8062-3 : 2007 C1 2009 | Identical |
| NS EN ISO 8062-3 : 2007 AC 2009 | Identical |
| I.S. EN ISO 8062-3:2007 | Identical |
| PN EN ISO 8062-3 : 2009 | Identical |
| SS-EN ISO 8062-3:2007 | Identical |
| NEN-EN-ISO 8062-3:2007 | Identical |
| BS EN ISO 8062-3:2007 | Identical |
| EN ISO 8062-3 : 2007 COR 2009 | Identical |
| DIN EN ISO 8062-3:2007-10 | Equivalent |
| UNE-EN ISO 8062-3:2009 | Identical |
| DIN 469:2014-06 | CRANK HANDLES, STRAIGHT PATTERN |
| 09/30200834 DC : 0 | BS EN 1559-1 - FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL |
| BS ISO 113:2010 | Rolling bearings. Plummer block housings. Boundary dimensions |
| I.S. EN 15776:2011 | UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM CAST IRON WITH AN ELONGATION AFTER FRACTURE EQUAL OR LESS THAN 15% |
| BS EN ISO 14978:2006 | Geometrical Product Specifications (GPS). General concepts and requirements for GPS measuring equipment |
| DIN EN ISO 14405-2:2012-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES (ISO 14405-2:2011) |
| I.S. EN ISO 14405-2:2011 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL TOLERANCING - PART 2: DIMENSIONS OTHER THAN LINEAR SIZES (ISO 14405-2:2011) |
| DIN EN 1982:2016-01 (Draft) | COPPER AND COPPER ALLOYS - INGOTS AND CASTINGS |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| BS EN 10340:2007 | Steel castings for structural uses |
| BS EN 15272-4:2007 | Inland navigation vessels. Equipment for rope leading Rope lead |
| BS EN 1559-1:2011 | Founding. Technical conditions of delivery General |
| CEN/TR 16749:2014 | Aluminium and aluminium alloys - Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products |
| DIN SPEC 91184 E : 2014 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013) |
| PREN 1090-3 : DRAFT 2017 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| DIN CEN ISO/TS 8062-2;DIN SPEC 91184:2014-03 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013) |
| 13/30252100 DC : 0 | BS ISO 4990 - STEEL CASTINGS - GENERAL TECHNICAL DELIVERY REQUIREMENTS |
| BS ISO 8062-4:2017 | Geometrical product specifications (GPS). Dimensional and geometrical tolerances for moulded parts General tolerances for castings using profile tolerancing in a general datum system |
| PD CEN ISO/TS 8062-2:2013 | Geometrical Product Specifications (GPS). Dimensional and geometrical tolerances for moulded parts Rules |
| 16/30321444 DC : DRAFT SEP 2016 | BS ISO 6482 - SHIPBUILDING - DECK MACHINERY - WARPING END PROFILES |
| ISO 6482:2017 | Shipbuilding — Deck machinery — Warping end profiles |
| EN 13445-6 : 2014 COR 2017 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| DIN 468:2014-06 | CRANK HANDLES, OFFSET TYPE |
| BS EN ISO 14405-2:2011 | Geometrical product specifications (GPS). Dimensional tolerancing Dimensions other than linear sizes |
| DIN EN 15776:2016-01 | Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 % (includes Amendment A1:2015) |
| I.S. EN 13445-6:2014 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| ISO 14405-2:2011 | Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear sizes |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| DIN EN 1559-1:2011-05 | Founding - Technical conditions of delivery - Part 1: General |
| I.S. EN 1982:2017 | COPPER AND COPPER ALLOYS - INGOTS AND CASTINGS |
| I.S. EN 1559-1:2011 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL |
| VDI 3120:2015-06 | Cast steel wall thicknesses in large stamping and forming dies - Design references for tools with more than 1000 mm side length |
| BS ISO 4990:2015 | Steel castings. General technical delivery requirements |
| DIN CEN/TR 16749;DIN SPEC 31601:2015-02 | ALUMINIUM AND ALUMINIUM ALLOYS - CLASSIFICATION OF DEFECTS AND IMPERFECTIONS IN HIGH PRESSURE, LOW PRESSURE AND GRAVITY DIE CAST PRODUCTS |
| ISO 113:2010 | Rolling bearings — Plummer block housings — Boundary dimensions |
| S.R. CEN ISO/TS 8062-2:2013 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013, CORRECTED VERSION 2013-11-01) |
| BS EN 15776 : 2011 | UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM CAST IRON WITH AN ELONGATION AFTER FRACTURE EQUAL OR LESS THAN 15% |
| ISO 8062-4:2017 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system |
| I.S. EN ISO 14978:2006 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT |
| 17/30347070 DC : 0 | BS EN 10340-2 - STEEL CASTINGS FOR STRUCTURAL USES - PART 2: TECHNICAL DELIVERY CONDITIONS |
| DIN EN 1706:2013-12 | ALUMINIUM AND ALUMINIUM ALLOYS - CASTINGS - CHEMICAL COMPOSITION AND MECHANICAL PROPERTIES |
| DIN EN 15272-4:2007-12 | Inland navigation vessels - Equipment for rope leading - Part 4: Rope lead |
| DIN EN 10340:2008-01 | Steel castings for structural uses |
| DIN EN ISO 14978:2006-09 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - GENERAL CONCEPTS AND REQUIREMENTS FOR GPS MEASURING EQUIPMENT |
| BS EN 1706:2010 | Aluminium and aluminium alloys. Castings. Chemical composition and mechanical properties |
| 08/30176073 DC : DRAFT APR 2008 | BS EN 15776 - UNFIRED PRESSURE VESSELS - ADDITIONAL REQUIREMENTS FOR THE DE SIGN AND FABRICATION OF PRESSURE VESSELS AND PARTS CONSTRUCTED FROM CAST IRON WITH ELONGATION EQUAL OR LESS THAN 15 PERCENT |
| 17/30347067 DC : 0 | BS EN 10340-1 - STEEL CASTINGS FOR STRUCTURAL USES - PART 1: GENERAL |
| 13/30274230 DC : 0 | BS EN 13445-6:2009/A1 - UNFIRED PRESSURE VESSELS - REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| BS ISO 6482:2017 | Shipbuilding. Deck machinery. Warping end profiles |
| BS EN 13445-6 : 2014 | UNFIRED PRESSURE VESSELS - PART 6: REQUIREMENTS FOR THE DESIGN AND FABRICATION OF PRESSURE VESSELS AND PRESSURE PARTS CONSTRUCTED FROM SPHEROIDAL GRAPHITE CAST IRON |
| ISO 14978:2006 | Geometrical product specifications (GPS) — General concepts and requirements for GPS measuring equipment |
| 17/30348949 DC : 0 | BS EN 1090-3 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| PREN 10340-2 : DRAFT 2017 | STEEL CASTINGS FOR STRUCTURAL USES - PART 2: TECHNICAL DELIVERY CONDITIONS |
| ISO 4990:2015 | Steel castings — General technical delivery requirements |
| BS EN 1982:2017 | Copper and copper alloys. Ingots and castings |
| I.S. EN 1706:2010 | ALUMINIUM AND ALUMINIUM ALLOYS - CASTINGS - CHEMICAL COMPOSITION AND MECHANICAL PROPERTIES |
| EN 15776:2011+A1:2015 | Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 % |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN 15272-4:2007 | Inland navigation vessels - Equipment for rope leading - Part 4: Rope lead |
| PD CEN/TR 16749:2014 | Aluminium and aluminium alloys. Classification of Defects and Imperfections in High Pressure, Low Pressure and Gravity Die Cast Products |
| S.R. CEN/TR 16749:2014 | ALUMINIUM AND ALUMINIUM ALLOYS - CLASSIFICATION OF DEFECTS AND IMPERFECTIONS IN HIGH PRESSURE, LOW PRESSURE AND GRAVITY DIE CAST PRODUCTS |
| PREN 1559-1 : DRAFT 2009 | FOUNDING - TECHNICAL CONDITIONS OF DELIVERY - PART 1: GENERAL |
| EN ISO 14405-2:2011 | Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes (ISO 14405-2:2011) |
| CEN ISO/TS 8062-2 : 2013 COR 2014 | GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - DIMENSIONAL AND GEOMETRICAL TOLERANCES FOR MOULDED PARTS - PART 2: RULES (ISO/TS 8062-2:2013, CORRECTED VERSION 2013-11-01) |
| ISO/TS 8062-2:2013 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules |
| I.S. EN ISO 14405-2:2019 | Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes (ISO 14405-2:2018) |
| I.S. EN 10340:2007 | STEEL CASTINGS FOR STRUCTURAL USES |
| UNE-EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| UNE-EN ISO 14405-2:2015 | Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear sizes (ISO 14405-2:2011) |
| UNE-EN 1982:2018 | Copper and copper alloys - Ingots and castings |
| UNE-EN 13445-6:2015 | Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheroidal graphite cast iron |
| UNE-EN 1706:2011 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| UNE-EN 15776:2011 | Unfired pressure vessels - Requirements for the design and fabrication of pressure vessels and pressure parts constructed from cast iron with an elongation after fracture equal or less than 15 % |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) — Masterplan |
| ISO 8015:2011 | Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules |
| ISO 5459:2011 | Geometrical product specifications (GPS) — Geometrical tolerancing — Datums and datum systems |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO/TS 8062-2:2013 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules |
| ISO 10135:2007 | Geometrical product specifications (GPS) — Drawing indications for moulded parts in technical product documentation (TPD) |
| ISO 1302:2002 | Geometrical Product Specifications (GPS) — Indication of surface texture in technical product documentation |
| ISO 8062-1:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 1: Vocabulary |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| ISO 10579:2010 | Geometrical product specifications (GPS) — Dimensioning and tolerancing — Non-rigid parts |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.