MIL-DTL-32234 Base Document:2007
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Connectors, Electrical, Ultra High Density, Modular, Blade and Fork, Eight Row, General Specification for
01-16-2007
05-17-2021
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
Specifies the detail requirements for ultra high density connectors, surface mounted on daughter board modules or fixed backplanes.
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Superseded
|
| SupersededBy |
This specification covers the detail requirements for ultra high density connectors, surface mounted on daughter board modules or fixed backplanes. The connector contacts are densely packed with .050 inch (1.27 mm) spacing between contact centers in the same row. These connectors are intended for use in assemblies requiring very densely packaged electronic components, and are commonly used in digital applications.
| MIL-DTL-32234-8 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Daughter Board, Eight Row, 396 Contact Positions |
| MIL-DTL-32234-3 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Backpanel, EMI/RFI Shielding, Eight Row, 196 Pins |
| MIL-STD-1353 Revision C:2014 | Electrical Connectors, Plug-in Sockets and Associated Hardware, Selection and Use of |
| MIL-DTL-32234-4 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Daughter Board, Eight Row, 196 Contact Positions |
| MIL-DTL-32234-2 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Daughter Board, Eight Row, 192 Contact Positions |
| MIL-DTL-32234-6 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Daughter Board, Eight Row, 372 Contact Positions |
| MIL-DTL-32234-5 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Backpanel, Eight Row, 372 Pins |
| MIL-DTL-32234-7 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Blade and Fork, Backpanel, Eight Row, 396 Pins |
| MIL-DTL-32234-1 Base Document:2007 | Connectors, Electrical, Ultra High Density, Modular, Blade and Fork, Backpanel, Eight Row, 192 Pins |
| MIL-DTL-32234-9 Base Document:2007 | Connector, Electrical, Ultra High Density, Modular, Keying Pins and Bushings |
| SAE AMS2404G | Plating, Electroless Nickel |
| MIL-DTL-5624 Revision W:2016 | Turbine Fuel, Aviation, Grades JP-5 (NATO F-44) |
| SAE AMS2402K | Plating, Zinc |
| ASTM G 21 : 2015 : REDLINE | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
| MIL-PRF-5606 Revision H:2002 | Hydraulic Fluid, Petroleum Base; Aircraft, Missile, and Ordnance |
| ASTM D 4067 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods |
| ASTM E 595 : 2015 : REDLINE | Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment |
| SAE AMSQQA200/8A | Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire, Extruded A96061 |
| SAE AMSQQN290C | Nickel Plating (Electrodeposited) |
| MIL-STD-889 Revision C:2016 | Galvanic Compatibility of Electrically Conductive Materials |
| MIL-PRF-87257 Revision C:2017 | Hydraulic Fluid, Fire Resistant; Low Temperature, Synthetic Hydrocarbon Base, Aircraft and Missile |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| SAE AMSR25988 | Rubber, Fluorosilicone Elastomer, Oil-and-Fuel-Resistant, Sheets, Strips, Molded Parts, and Extruded Shapes |
| ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
| ASTM D 5138 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP) |
| ASTM B 567 : 1998 | Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method |
| MIL-PRF-23699 Revision G:2014 | Lubricating Oil, Aircraft Turbine Engine, Synthetic Base, NATO Code Numbers: O-152, O-154, O-156, and O-167 |
| MIL-STD-790 Revision G:2011 | Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications |
| SAE AMSQQA225B | Aluminum and Aluminum Alloy, Bar, Rod, Wire, or Special Shapes; Rolled, Drawn, or Cold Finished; General Specification For |
| ASTM B 194 : 2015 : REDLINE | Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar |
| SAE AMS2700E | Passivation of Corrosion Resistant Steels |
| SAE AMS5640V | Steel, Corrosion-Resistant, Bars, Wire, and Forgings 18Cr - 9.0Ni Free Machining |
| MIL-M-24519 Revision E:1992 | Molding Plastics, Electrical, Thermoplastic |
| MIL-STD-202 Revision H:2015 | Electronic and Electrical Component Parts |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| SAE AMS QQ A 200 : 2004 | ALUMINUM ALLOY, BAR, ROD, SHAPES, STRUCTURAL SHAPES, TUBE, AND WIRE, EXTRUDED: GENERAL SPECIFICATION FOR |
| SAE AS39029D | Contacts, Electrical Connector, General Specification For |
| MIL-STD-1285 Revision D:2004 | Marking of Electrical and Electronic Parts |
| ASTM A 342/A342M : 2014 : REDLINE | Standard Test Methods for Permeability of Weakly Magnetic Materials |
| FED-STD-H28 Revision A:1994 | Screw-Thread Standards for Federal Services |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.