NEMA ICS 18:2001 (R2007)
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
INDUSTRIAL CONTROL AND SYSTEMS: MOTOR CONTROL CENTERS
Hardcopy , PDF
04-24-2023
English
12-06-2012
Foreword
1 GENERAL
1.1 Referenced Standards
1.2 Scope
1.3 Normative References
1.4 Equipment
2 DEFINITIONS
3 CLASSIFICATIONS
3.1 Classes and Types
3.2 Classes of Motor Control Centers
3.2.1 Class I-Independent Units
3.2.2 Class II-Interconnected Units
3.2.3 Class I-S & II-S-Motor Control Centres with
Custom Drawing Requirements
3.3 Circuit Wiring
3.3.1 Types of Wiring
4 CHARACTERISTICS AND RATINGS
4.1 Voltage Ratings
4.2 Combination Motor-Control Unit Ratings
4.3 Continuous-Current Ratings of Buses
4.4 Basis for Short-Circuit Current Rating of Motor Control
Centres
4.4.1 Available Short-Circuit Current
4.4.2 Series Combination Rating
4.5 Standard Short-Circuit Ratings of Motor Control Centres
4.5.1 Ratings of Combination Motor-Control Unit and
Feeder-Tap Units
4.5.2 Units Not Containing a Short-Circuit Protective
Device
4.5.3 Separately Derived Systems
4.5.4 Rating of Bus Structure
4.6 Range of Operating Voltage
5 PRODUCT MARKING, INSTALLATION AND MAINTENANCE INFORMATION
5.1 Preventive Maintenance
5.2 Handling, Installation, Operation, and Maintenance
5.3 Marking and Labelling
5.3.1 Units
5.3.2 Section(s)
5.3.3 Marking Exception
6 SERVICE AND STORAGE CONDITIONS
7 CONSTRUCTION
7.1 Vertical Section
7.2 Wiring Space
7.3 Unit Mounting
7.4 Interlocking of Doors
7.5 Spacings
7.6 Control Circuit Protection
7.7 Lighting Panel and Auxiliary Control Panel Protection
8 PERFORMANCE REQUIREMENTS AND TESTS
8.1 Design Test Concept
8.2 Test Methods
8.3 Horizontal Common Power Bus and Vertical Extension
Short-Circuit Withstand Test
8.3.1 Tests
8.3.2 Performance Criteria
8.4 Combination Motor-Control Units and Feeder-Tap Units
Short-Circuit Interrupting Tests
8.4.1 Tests
8.4.2 Performance Criteria
8.4.3 Location of Units
8.4.4 Unit Fault Connection
8.4.5 Enclosure Ground Circuit
8.4.6 Test Voltage and Frequency
8.4.7 Test Current
8.4.8 Test Circuit Calibration
8.4.9 Test Duty Cycle
8.4.10 Performance Rise Test
9 APPLICATION
9.1 Technical Information Needed to Supply a Motor Control
Center
9.2 Application of Short-Circuit Current Ratings
Applies to three phase 50 and 60 hertz motor control centers rated not more than 600 volts AC.
DocumentType |
Standard
|
Pages |
24
|
PublisherName |
National Electrical Manufacturers Association
|
Status |
Withdrawn
|
ASME B30.29 : 2012 | SELF-ERECTING TOWER CRANES - SAFETY STANDARD FOR CABLEWAYS, CRANES, DERRICKS, HOISTS, HOOKS, JACKS, AND SLINGS |
NEMA ICS 20:2009 (R2015) | Informational Guide to Electrical Industrial Topics |
NEMA ICS 3.1 : 2009(R2014) | GUIDE FOR THE APPLICATION, HANDLING, STORAGE, INSTALLATION, AND MAINTENANCE OF MEDIUM-VOLTAGE AC CONTACTORS, CONTROLLERS, AND CONTROL CENTERS |
PIP ELSMC14 : 2013 | LOW-VOLTAGE SWITCH RACK SPECIFICATION |
PIP ELSMC13 : 2013 | LOW-VOLTAGE MOTOR CONTROL CENTERS |
IEEE 3001.11-2017 | IEEE Recommended Practice for Application of Controllers and Automation to Industrial and Commercial Power Systems |
IEEE 1683-2014 | IEEE Guide for Motor Control Centers Rated up to and including 600 V AC or 1000 V DC with Recommendations Intended to Help Reduce Electrical Hazards |
PIP ELSMC14 : 2019 | LOW-VOLTAGE SWITCH RACK SPECIFICATION |
NEMA ICS 1.3:1986 (R2001, R2009, R2015) | Preventive Maintenance of Industrial Control and Systems Equipment |
IEEE C37.26-2014 REDLINE | IEEE Guide for Methods of Power-Factor Measurement for Low-Voltage (1000 V AC or lower) Inductive Test Circuits |
NEMA 250 : 2014 | ENCLOSURES FOR ELECTRICAL EQUIPMENT (1000 VOLTS MAXIMUM) |
NEMA ICS 6-1993 (R2006) | Industrial Control and Systems: Enclosures |
IEEE 4-2013 | IEEE Standard for High-Voltage Testing Techniques |
IEEE C37.09-1999 | IEEE Standard Test Procedure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis |
NEMA ICS 1 : 2000(R2015) | INDUSTRIAL CONTROL AND SYSTEMS: GENERAL REQUIREMENTS |
NEMA ICS 2:2008 | Controllers, Contactors and Overload Relays Rated 600 V |
NEMA ICS 2.3 : 1995(R2008) | INDUSTRIAL CONTROL AND SYSTEMS: INSTRUCTIONS FOR THE HANDLING, INSTALLATION, OPERATION AND MAINTENANCE OF MOTOR CONTROL CENTERS |
IEEE 141 : 1993 | IEEE Recommended Practice for Electric Power Distribution for Industrial Plants |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.