PD IEC/TS 60034-32:2016
Withdrawn
Rotating electrical machines Measurement of stator end-winding vibration at form-wound windings
Hardcopy
English
01-31-2017
11-05-2021
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
4 Causes and effects of stator end-winding vibrations
5 Measurement of stator end-winding structural
dynamics at standstill
6 Measurement of end-winding vibration during
operation
7 Repeated measurements for detection of structural
changes
Annex A (informative) - Background causes and effects
of stator end-winding vibrations
Annex B (informative) - Data visualization
Bibliography
Gives consistent guidelines for measuring and reporting end-winding vibration behaviour during operation and at standstill.
| Committee |
PEL/2
|
| DocumentType |
Standard
|
| Pages |
66
|
| PublisherName |
British Standards Institution
|
| Status |
Withdrawn
|
IECTS60034-32:2016(E) is intended to provide consistent guidelines for measuring and reporting end-winding vibration behaviour during operation and at standstill. It
- defines terms for measuring, analysis and evaluation of stator end-winding vibration and related structural dynamics;
- gives guidelines for measuring dynamic / structural characteristics offline and stator end-winding vibrations online;
- describes instrumentation and installation practices for end-winding vibration measurement equipment;
- establishes general principles for documentation of test results;
- describes the theoretical background of stator end-winding vibrations. This part of IEC60034 is applicable to three-phase synchronous generators and three-phase synchronous direct online (DOL) motors.
| Standards | Relationship |
| IEC TS 60034-32:2016 | Identical |
| ISO 13373-1:2002 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures |
| IEC 60034-18-32:2010 | Rotating electrical machines - Part 18-32: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation by electrical endurance |
| IEC TS 60034-27:2006 | Rotating electrical machines - Part 27: Off-line partial discharge measurements on the stator winding insulation of rotating electrical machines |
| ISO 7626-1:2011 | Mechanical vibration and shock — Experimental determination of mechanical mobility — Part 1: Basic terms and definitions, and transducer specifications |
| ISO 13373-2:2016 | Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 2: Processing, analysis and presentation of vibration data |
| ISO 7626-5:1994 | Vibration and shock — Experimental determination of mechanical mobility — Part 5: Measurements using impact excitation with an exciter which is not attached to the structure |
| ISO 18431-1:2005 | Mechanical vibration and shock — Signal processing — Part 1: General introduction |
| ISO 2041:2009 | Mechanical vibration, shock and condition monitoring — Vocabulary |
| ISO 16063-1:1998 | Methods for the calibration of vibration and shock transducers — Part 1: Basic concepts |
| IEC 60034-18-34:2012 | Rotating electrical machines - Part 18-34: Functional evaluation of insulation systems - Test procedures for form-wound windings - Evaluation of thermomechanical endurance of insulation systems |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| IEC 60034-18-31:2012 | Rotating electrical machines - Part 18-31: Functional evaluation of insulation systems - Test procedures for form-wound windings - Thermal evaluation and classification of insulation systems used in rotating machines |
| ISO 18431-2:2004 | Mechanical vibration and shock — Signal processing — Part 2: Time domain windows for Fourier Transform analysis |
| IEC TS 60034-18-33:2010 | Rotating electrical machines - Part 18-33: Functional evaluation of insulation systems - Test procedures for form-wound windings - Multifactor evaluation by endurance under simultaneous thermal and electrical stresses |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.