• There are no items in your cart

PREN 13852 : DRAFT 2000

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES

Superseded date

05-01-2004

Published date

01-12-2013

Foreword
0 Introduction
1 Scope
2 Normative references
3 Definitions and symbols
4 Lists of hazards
5 Safety requirements and/or measures
  5.1 General
  5.2 Design - General
      5.2.1 General principles and requirements
      5.2.2 In - service loads
      5.2.3 Out of service loads
      5.2.4 Failure mode
  5.3 Design - requirements for equipment
      5.3.1 Electrotechnical equipment
      5.3.2 Non electrotechnical equipment
      5.3.3 Simultaneous motion
      5.3.4 Slewing bearings
      5.3.5 Slewing ring bolts
      5.3.6 Winches and brakes
      5.3.7 Wire rope termination
      5.3.8 Wire rope anchorage
      5.3.9 Wire rope strength
      5.3.10 Hydraulic cylinders
      5.3.11 Motion compensators and shock absorbers
  5.4 Design - requirements for health and safety
      5.4.1 Control stations - general
      5.4.2 Control Cabin
      5.4.3 Controls, indicators and limiting devices
      5.4.4 Telecommunications
      5.4.5 Overload and over-moment protection
      5.4.6 Lifting of persons
6 Verification of safety requirements and/or measures
7 Information for use
  7.1 Documentation
  7.2 Maintenance and inspection
  7.3 Operating instructions
      7.3.1 General
      7.3.2 Lifting of persons (if part of the intended use)
  7.4 Marking
      7.4.1 Manufacturer's plate
      7.4.2 Rated capacity information
      7.4.3 Components
  7.5 Training
  7.6 Testing
      7.6.1 General
      7.6.2 Function test
      7.6.3 Static test
      7.6.4 Test loads
Annex A (normative) Determination of factors
      A.1 Calculation of the dynamic coefficient Phi[n]
          by the simplified method
      A.2 Calculation of dynamic coefficient Phi[n] by motion
          response analysis
      A.3 Out-of-plane influences
          A.3.1 Offlead load
          A.3.2 Sidelead load
          A.3.3 Horizontal load combination of the out-of-plane
                influences
      A.4 Hook velocity
          A.4.1 Hoisting velocity
          A.4.2 Horizontal hook velocity
Annex B (normative) Environmental influences
      B.1 General
      B.2 Wind loads
          B.2.1 Mean wind velocities
          B.2.2 Dynamic wind loads
          B.2.3 Boom stalling
      B.3 Floating Units
      B.4 Heat protection
      B.5 Ice 37
      B.6 Stowage
      B.7 Corrosion protection
Annex C (normative) Failure mode analysis
      C.1 General
      C.2 Failure mode charts
      C.3 Failure mode for sideload
Annex D (normative) Material selection
      D.1 General
      D.2 Verification of material quality
      D.3 Forged rings for slewing bearings
      D.4 Slew ring bolts
      D.5 Welded structures
      D.6 Non welded components
Annex E (informative) Control station instrumentation
Annex F (normative) Rope safety factors
      F.1 Wire ropes
          F.1.1 Running rigging
          F.1.2 Standing rigging
Annex G (normative) Slew rings
Annex H (normative) Requirements for brakes
Annex J (normative) Ranking of safety systems
Annex K (normative) Winches
Annex L (informative) Typical general purpose offshore cranes
                       and terminology
Annex M (informative) Excursion envelopes for offlead and sidelead
Annex ZA (informative) Relationship of this European Standard
                       with EU Directives

Specifies the requirements for general purpose offshore cranes. Applicable to cranes, which are manufactured after the date of issue of this standard. Includes requirements of lifting of persons.

Committee
TC 147
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
00/707659 DC : DRAFT APR 2000 Identical
NEN EN 13852 : DRAFT 2000 Identical
DIN EN 13852:2000-06 (Draft) Identical

CSA ISO 19904-1 : 2007 : R2012 PETROLEUM AND NATURAL GAS INDUSTRIES - FLOATING OFFSHORE STRUCTURES - PART 1: MONOHULLS, SEMI-SUBMERSIBLES AND SPARS
CSA ISO 19904-1 : 2007 : R2017 PETROLEUM AND NATURAL GAS INDUSTRIES - FLOATING OFFSHORE STRUCTURES - PART 1: MONOHULLS, SEMI-SUBMERSIBLES AND SPARS
CSA ISO 19904-1 : 2007 PETROLEUM AND NATURAL GAS INDUSTRIES - FLOATING OFFSHORE STRUCTURES - PART 1: MONOHULLS, SEMI-SUBMERSIBLES AND SPARS

EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
EN 418 : 1992 SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 12480-1:1997 Cranes Safe use Part 1: General
ISO 9926-1:1990 Cranes — Training of drivers — Part 1: General
PREN 13001-2 : DRAFT 2012 CRANE SAFETY - GENERAL DESIGN - PART 2: LOAD ACTIONS
EN 50020:2002 Electrical apparatus for potentially explosive atmospheres - Intrinsic safety 'i'
PREN 13135-1 : DRAFT 1998 CRANES - SAFETY - DESIGN - REQUIREMENTS FOR EQUIPMENT - PART 1: ELECTROTECHNICAL EQUIPMENT
ISO 12478-1:1997 Cranes — Maintenance manual — Part 1: General
ISO 8566-1:2010 Cranes Cabins and control stations Part 1: General
EN 10025:1990/A1:1993 HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS
ISO 9927-1:2013 Cranes — Inspections — Part 1: General
EN 50017:1998 Electrical apparatus for potentially explosive atmospheres - Powder filling "q"
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN 50019:2000/corrigendum Apr. 2003 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - INCREASED SAFETY "E"
EN 50018 : 2000 AMD 1 2002 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - FLAMEPROOF ENCLOSURE "D"
EN 292-1 : 1991 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY
EN 842:1996+A1:2008 Safety of machinery - Visual danger signals - General requirements, design and testing
EN 10204:2004 Metallic products - Types of inspection documents
EN 10083-1:2006 Steels for quenching and tempering - Part 1: General technical delivery conditions
ISO 7752-1:2010 Cranes Control layout and characteristics Part 1: General principles
EN 10083-2:2006 Steels for quenching and tempering - Part 2: Technical delivery conditions for non alloy steels
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN 954-1 : 1996 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN
EN 292-2 : 91 AMD 1 95 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION
EN 50015:1998 Electrical apparatus for potentially explosive atmospheres - Oil immersion "o"
EN 50016:2002 Electrical apparatus for potentially explosive atmospheres - Pressurized apparatus "p"
PREN 12644-3 : DRAFT 1997 CRANES - SAFETY - REQUIREMENTS FOR INSPECTION AND USE - PART 3: FITNESS FOR PURPOSE
EN 457 : 1992 SAFETY OF MACHINERY - AUDITORY DANGER SIGNALS - GENERAL REQUIREMENTS, DESIGN AND TESTING
EN 50014:1997/A2:1999 ELECTRICAL APPARATUS FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - GENERAL REQUIREMENTS
ISO 12482-1:1995 Cranes Condition monitoring Part 1: General
EN 1070 : 1998 SAFETY OF MACHINERY - TERMINOLOGY
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.