PREN 2002-02 : 200P3
Withdrawn
View Superseded by
AEROSPACE SERIES - METALLIC MATERIALS - TEST METHODS - PART 2: TENSILE TESTING AT ELEVATED TEMPERATURE
Hardcopy , PDF
English
12-06-2023
0 Introduction
1 Scope
2 Normative references
3 Definitions
4 Health and safety
5 Principle
6 Testing requirements
7 Test report
Annex A (normative) Types of test piece to be used for sheet
and strip with thickness less than 8 mm
Annex B (normative) Types of non-machined test piece to be used
in the case of bar, section and wire with a
diameter or thickness less than or equal to
8 mm
Annex C (normative) Types of machined test piece to be used in
the case of bar, section, plate and wire
with diameter or thickness greater than 8 mm
and for forgings and castings
Annex D (normative) Types of test piece to be used in the case
of tubes
Specifies the requirements for the tensile testing of metallic materials at elevated temperature for aerospace applications.
| Committee |
C5
|
| DocumentType |
Draft
|
| Pages |
20
|
| ProductNote |
Superseded by EN 2002-002:2005
|
| PublisherName |
Aerospace & Defence Industries Association of Europe
|
| Status |
Withdrawn
|
| SupersededBy |
| 01/716044 DC : 0 | EN 4800-6 - AEROSPACE SERIES - TITANIUM AND TITANIUM ALLOYS - TECHNICAL SPECIFICATION - PART 6: PRE-PRODUCTION AND PRODUCTION FORGINGS |
| PREN 3225-4 : 200P1 | AEROSPACE SERIES - HEAT RESISTING ALLOYS PRODUCED FROM ATOMIZED POWDER - POWDER COMPACTED FORGING STOCK AND PARTS - TECHNICAL SPECIFICATION - PART 4 - PRE-PRODUCTION AND PRODUCTION PARTS |
| BS EN 2858-3:1994 | Titanium and titanium alloys. Forging stock and forgings. Technical specifications Pre-production and production forgings |
| DIN EN 2103-2:1991-11 | AEROSPACE SERIES - AEROSPACE SERIES - STEEL, NICKEL BASE AND COBATT BASE ALLOY REMELTING STOCK AND CASTINGS - TECHNICAL SPECIFICATION - PART 2 - REMELTING STOCK |
| EN 2103-3:1991 | Aerospace series - Steel, nickel base and cobalt base alloy remelting stock and castings - Technical specifications - Part 3: Pre-production and production castings |
| PREN 4400-2 : 200P1 | AEROSPACE SERIES - ALUMINIUM AND ALUMINIUM ALLOY WROUGHT PRODUCTS - TECHNICAL SPECIFICATION - PART 2: SHEET AND STRIP |
| PREN 2002-23 : 200P1 | AEROSPACE SERIES - TEST METHODS FOR METALLIC MATERIALS - PART 23 - SHARP-NOTCH TENSION TESTING |
| BS EN 2858-2:1994 | Titanium and titanium alloys. Forging stock and forgings. Technical specification. Forging stock |
| EN 2103-2:1991 | Aerospace series - Steel, nickel base and cobalt base alloy remelting stock and castings - Technical specification - Part 2: Remelting stock |
| PREN 3225-3 : 200P1 | AEROSPACE SERIES - HEAT RESISTING ALLOYS PRODUCED FROM ATOMIZED POWDER - POWDER COMPACTED FORGING STOCK AND PARTS - TECHNICAL SPECIFICATION - PART 3 - HOT COMPACTED FORGING STOCK |
| EN 60584-2:1993 | Thermocouples - Part 2: Tolerances |
| PREN 4259 : 200P1 | AEROSPACE SERIES - METALLIC MATERIALS - DEFINITION OF GENERAL TERMS |
| EN 10002-4 : 1994 | METALLIC MATERIALS - TENSILE TEST - VERIFICATION OF EXTENSOMETERS USED IN UNIAXIAL TESTING |
| EN 4258:1998 | Aerospace series - Metallic materials - General organization of standardization - Links between types of EN standards and their use |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.