SAE ARP5796
Current
The latest, up-to-date edition.
Flight Critical Control Valves, Military Aircraft
07-09-2013
1. SCOPE
2. REFERENCES
3. REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. NOTES
This SAE Aerospace Recommended Practice (ARP) provides guidance in the design, development, qualification test, process control and production acceptance test for flight critical control valve (FCCV) design used in military flight control servoactuators where loss of single valve control could cause a catastrophic failure resulting in death, permanent total disability, and/or financial loss exceeding a defined contractual limit.
DocumentType |
Standard
|
PublisherName |
SAE International
|
Status |
Current
|
This SAE Aerospace Recommended Practice (ARP) provides guidance in the design, development, qualification test, process control and production acceptance test for flight critical control valve (FCCV) design used in military flight control servoactuators where loss of single valve control could cause a catastrophic failure resulting in death, permanent total disability, and/or financial loss exceeding a defined contractual limit. The FCCV, which is one element of a flight control actuator servo control loop, is a variable position control valve which modulates fluid into and out of the servoactuator power stage cylinders. The FCCV may be mechanically driven by either a mechanical flight control system as shown in FIGURE 1 or hydraulically driven from electro-hydraulic servo valve (EHSV) modulation control flow as shown in FIGURE 2. This type of control valve is not an EHSV or a direct drive valve (DDV).The FCCV is used in military hydraulic systems which conform to AS5440.
SAE AS4716B | Gland Design, O-ring and Other Elastomeric Seals |
SAE ARP 5580 : 2012 | RECOMMENDED FAILURE MODES AND EFFECTS ANALYSIS (FMEA) PRACTICES FOR NON-AUTOMOBILE APPLICATIONS |
MIL-PRF-6083 Revision G:2013 | HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION |
SAE AS9102B | Aerospace First Article Inspection Requirement |
MIL-PRF-46170 Revision E:2013 | HYDRAULIC FLUID, RUST INHIBITED, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, NATO CODE NO. H-544 |
SAE AMS7276H | Rubber: Fluorocarbon (FKM) High-Temperature-Fluid Resistant Low Compression Set For Seals In Fuel Systems and Specific Engine Oil Systems |
SAE AMS3216G | Fluorocarbon (FKM) Rubber High-Temperature - Fluid Resistant Low Compression Set 70 to 80 |
DI-SAFT-80101 Revision C:2015 | SYSTEM SAFETY HAZARD ANALYSIS REPORT (SSHAR) |
SAE AMSR83485A | Rubber, Fluorocarbon Elastomer, Improved Perfrormance At Low Temperatures |
SAE AS 9017 : 2009 | CONTROL OF AVIATION CRITICAL SAFETY ITEMS |
SAE AS5440A | Hydraulic Systems, Military Aircraft, Design and Installation, Requirements For |
SAE AMSP83461 | Packing, Preformed, Petroleum Hydraulic Fluid Resistant, Improved Performance at 275°F (135°C) |
MIL-STD-756 Revision B:1981 | RELIABILITY MODELING AND PREDICTION |
SAE AS9100D | Quality Management Systems - Requirements for Aviation, Space, and Defense Organizations |
SAE AIR4543C | Aerospace Hydraulics and Actuation Lessons Learned |
MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
SAE AMS7259E | Rubber: Fluorocarbon (FKM) High Temperature/Fluid Resistant Low Compression Set/85 to 95 Hardness For Seals In Fuel Systems and Specific Engine Oil Systems |
SAE AIR1243D | Anti Blow-By Design Practice for Cap Seals |
ANSI/NCSL Z540 1 : 94(R2002) | CALIBRATION - CALIBRATION LABORATORIES AND MEASURING AND TEST EQUIPMENT - GENERAL REQUIREMENTS |
SAE ARP4904A | Capability Guidelines for Computer Controlled Test Equipment for Hydraulic Components |
MIL-STD-882 Revision E:2012 | System Safety |
SAE AMS3218C | Fluorocarbon (FKM) Rubber High-Temperature-Fluid Resistant Low Compression Set 85 to 95 |
ASTM E 1444 : 2005 | Standard Practice for Magnetic Particle Testing |
SAE AIR 5273 : 2001 | ACTUATION SYSTEM FAILURE DETECTION METHODS |
SAE AS 8775 : 1998 | HYDRAULIC SYSTEM COMPONENTS, AIRCRAFT AND MISSILES, GENERAL SPECIFICATION FOR |
SAE AMS5630L | Steel, Corrosion-Resistant, Bars, Wire, and Forgings 17Cr - 0.52Mo (0.95 - 1.20C) (440C) |
SAE AMS2700E | Passivation of Corrosion Resistant Steels |
MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
SAE AS 4059F : 2013 | AEROSPACE FLUID POWER - CONTAMINATION CLASSIFICATION FOR HYDRAULIC FLUIDS |
SAE ARP4386C | Terminology and Definitions for Aerospace Fluid Power, Actuation and Control Technologies |
SAE AMS2759/5D | Heat Treatment Martensitic Corrosion-Resistant Steel Parts |
SAE ARP 1383 : 2013 | AEROSPACE - IMPULSE TESTING OF HYDRAULIC COMPONENTS |
MIL-STD-1629 Revision A:1980 | PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS AND CRITICALITY ANALYSIS |
SAE ARP 5941 : 2014 | AEROSPACE FLUID POWER - CONTAMINATION SENSITIVITY - CONSIDERATIONS FOR ESTABLISHING TEST PROCEDURES FOR FLIGHT CONTROL ACTUATORS |
SAE JA 1000 : 2012 | RELIABILITY PROGRAM STANDARD |
GEIA EIA649B:2011 | CONFIGURATION MANAGEMENT STANDARD |
ISO 10012-1:1992 | Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment |
MIL-STD-785 Revision B:1980 | RELIABILITY PROGRAM FOR SYSTEMS AND EQUIPMENT DEVELOPMENT AND PRODUCTION |
ASTM D 1744 : 2013 | Standard Test Method for Determination of Water in Liquid Petroleum Products by Karl Fischer Reagent (Withdrawn 2016) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.