• Shopping Cart
    There are no items in your cart

SAE J517_201710

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Hydraulic Hose

Available format(s)

Hardcopy , PDF

Superseded date

07-20-2020

Superseded by

SAE J517_202007

Language(s)

English

Published date

10-18-2017

US$162.84
Excluding Tax where applicable

1 SCOPE
2 REFERENCES
3 DEFINITIONS
4 AGE CONTROL
5 HOSE CONNECTORS
6 HOSE ASSEMBLIES
7 HOSE CUT END ANGLE DIMENSION
8 APPLICATION FACTORS
9 SIZE DESIGNATIONS
10 HOSE IDENTIFICATION
11 ORIENTATION OF OFFSET ELBOW ENDS IN A
   HOSE ASSEMBLY
12 ASSEMBLY LENGTH
13 TESTS
14 INSPECTION RETESTS AND REJECTION
15 ORDERING INFORMATION (FOR DOD
   PROCUREMENT ONLY)
16 ONE STEEL WIRE BRAID REINFORCED, RUBBER
   COVERED HYDRAULIC HOSE (SAE 100R1)
17 TWO STEEL WIRE BRAID REINFORCED, RUBBER
   COVERED HYDRAULIC HOSE (SAE 100R2)
18 DOUBLE FIBER BRAID (NONMETALLIC),
   RUBBER COVERED HYDRAULIC HOSE (SAE 100R3)
19 WIRE INSERTED HYDRAULIC SUCTION HOSE (SAE 100R4)
20 SINGLE WIRE BRAID, TEXTILE COVERED
   HYDRAULIC HOSE (SAE 100R5)
21 FIBER REINFORCED (NONMETALLIC), RUBBER
   COVERED HYDRAULIC HOSE (SAE 100R6)
22 THERMOPLASTIC HYDRAULIC HOSE (SAE 100R7)
23 HIGH PRESSURE THERMOPLASTIC HYDRAULIC
   HOSE (SAE 100R8)
24 FOUR SPIRAL STEEL WIRE REINFORCED,
   RUBBER COVERED HYDRAULIC HOSE (SAE 100R12)
25 MULTIPLE SPIRAL STEEL WIRE REINFORCED,
   RUBBER COVERED HYDRAULIC HOSE (SAE 100R13)
26 PTFE LINED HYDRAULIC HOSE (SAE 100R14)
27 MULTIPLE SPIRAL STEEL WIRE REINFORCED,
   RUBBER COVERED HYDRAULIC HOSE (SAE 100R15)
28 COMPACT, ONE AND TWO STEEL WIRE BRAID
   REINFORCED, RUBBER COVERED HYDRAULIC HOSE (SAE 100R16)
29 COMPACT, 21 MPa MAXIMUM WORKING
   PRESSURE, ONE AND TWO STEEL WIRE REINFORCED,
   RUBBER COVERED HYDRAULIC HOSE (SAE 100R17)
30 21 MPa THERMOPLASTIC HYDRAULIC HOSE (SAE 100R18)
31 COMPACT, 28 MPA MAXIMUM WORKING
   PRESSURE, ONE AND TWO STEEL WIRE REINFORCED,
   RUBBER COVERED HYDRAULIC HOSE (SAE 100R19)
32 NOTES

Specifies general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment.

DevelopmentNote
Supersedes A A 52413. (07/2003) Supersedes MIL H 52471/6 (A). (12/2008)
DocumentType
Standard
Pages
38
PublisherName
SAE International
Status
Superseded
SupersededBy
Supersedes

This SAE Standard provides general, dimensional and performance specifications for the most common hoses used in hydraulic systems on mobile and stationary equipment.The general specifications contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifications for the 100R-series hoses contained in the later sections of this document (see Tables 1 and 2).This document shall be utilized as a procurement document only to the extent as agreed upon by the manufacturer and user.The maximum working pressure of a hose assembly comprising SAE J517 hose and hose connectors per SAE J516, SAE J518, SAE J1453, etc., shall not exceed the lower of the respective SAE maximum working pressure values.When using SAE J517 hose for marine applications, reference SAE J1475, SAE J1942, and SAE J1942-1.The SAE J517 100R9, 100R10, and 100R11 hoses are discontinued due to lack of demand. For DOD orders see Appendix C.The SAE J517 100R1A, 100R2A, 100R2B, and 100R 2BT are discontinued due to lack of demand. For DOD orders replace 100R1A with 100R1AT, replace 100R2A, 100R2B, and 100R2BT with 100R2AT.The SAE J517 100R1AT maximum working pressures were replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R1 as type S.The SAE J517 100R2AT maximum working pressures were replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R2 as type S.The SAE J517 100R16 maximum working pressures were replaced by the type S maximum working pressures beginning with the year 2009, eliminating the need to label 100R16 as type S.

ISO 3862:2017 Rubber hoses and hose assemblies Rubber-covered spiral-wire-reinforced hydraulic types for oil-based or water-based fluids Specification
SAE J846_201511 Coding Systems for Identification of Fluid Conductors and Connectors
SAE J518_201303 Hydraulic Flanged Tube, Pipe, and Hose Connections, Four-Bolt Split Flange Type
SAE J1475_201406 Hydraulic Hose Fitting for Marine Applications
ISO 3949:2009 Plastics hoses and hose assemblies Textile-reinforced types for hydraulic applications Specification
SAE J1401_201302 Road Vehicle - Hydraulic Brake Hose Assemblies for Use With Nonpetroleum-Base Hydraulic Fluids
MIL-PRF-7808 Revision L:1997 LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE
SAE J516_201604 Hydraulic Hose Fittings
ISO 4397:2011 Fluid power connectors and associated components — Nominal outside diameters of tubes and nominal hose sizes
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
SAE J1273_201409 Recommended Practices for Hydraulic Hose Assemblies
SAE J343_201605 Test and Test Procedures for SAE 100R Series Hydraulic Hose and Hose Assemblies
ISO 4079:2017 Rubber hoses and hose assemblies Textile-reinforced hydraulic types for oil-based or water-based fluids Specification
SAE J1453/1_201205 Specification for O-Ring Face Seal Connectors: Part 1 - Tube Connection Details and Common Requirements for Performance and Tests
ISO 11237:2017 Rubber hoses and hose assemblies — Compact wire-braid-reinforced hydraulic types for oil-based or water-based fluids — Specification
SAE J1942/1_201612 Qualified Hoses for Marine Applications
MIL-PRF-83282 Revision D:1997 HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537
SAE J1942_201406 Hose and Hose Assemblies for Marine Applications
SAE J1927_201406 Cumulative Damage Analysis for Hydraulic Hose Assemblies
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
SAE J1176_201206 External Leakage Classifications for Hydraulic Systems
ISO 6803:2017 Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
MIL H 8446 : LATEST HYDRAULIC FLUID, NONPETROLEUM BASE, AIRCRAFT
ISO 1436:2017 Rubber hoses and hose assemblies Wire-braid-reinforced hydraulic types for oil-based or water-based fluids Specification
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
FED-STD-595 Revision C:2008 COLORS USED IN GOVERNMENT PROCUREMENT
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.