IEC 60127-6:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Miniature fuses - Part 6: Fuse-holders for miniature fuse-links
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
10-26-2023
English - French
09-03-2014
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 Preferred standard ratings and classifications
for fuse-holders
6 Marking
7 Clause deleted
8 General notes on tests
9 Protection against electric shock
10 Clearances and creepage distances
11 Electrical requirements
12 Mechanical requirements
13 Thermal requirements
14 Endurance
15 Additional requirements
Annex A (normative) - Test PC board for fuse-holders
of rated currents up to 10 A
Annex B (normative) - Type tests, test sequences and
number of samples
Annex C (informative) - Insulation coordination
Annex D (informative) - Additional tests and
requirements
Annex E (informative) - Information for the correct
application of the fuse-holder
Bibliography
IEC 60127-6:2014 is applicable to fuse-holders for miniature cartridge fuse-links according to IEC 60127-2 and sub-miniature fuse-links according to IEC 60127-3 for the protection of electric appliances, electronic equipment and component parts thereof, normally intended for use indoors. Examples of fuse-holder types with different features are given. This part of IEC 60127 applies to fuse-holders with:
- a maximum rated current of 16 A; and
- a maximum rated voltage of 1 500 V d.c. or 1 000 V a.c.; and
- for use up to 2 000 m above sea-level, unless otherwise specified. The object of this standard is to establish uniform requirements for safety and the assessment of electrical, mechanical, thermal and climatic properties of fuse-holders and the compatibility between fuse-holders and fuse-links. This second edition cancels and replaces the first edition published in 1994, its Amendment 1 (1996) and Amendment 2 (2002). This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- modify the arrangement of the fuse-holder samples in the planes in 13.1.1;
- add a new test 13.2.2: Glow-wire ignition test;
- change maximum gauge size for standard sheets 3 and 4 from 0,70 to 0,63 in table 5;
- change minimum gauge size for standard sheets 3 and 4 from 0,55 to 0,56 in table 5. Keywords: fuse-holders for miniature cartridge fuse-links, sub-miniature fuse-links, protection of electric appliances, electronic equipment and component parts.
Committee |
TC 32/SC 32C
|
DevelopmentNote |
Supersedes IEC 60257 (03/2001) Stability date: 2019. (09/2017)
|
DocumentType |
Standard
|
Pages |
110
|
PublisherName |
International Electrotechnical Committee
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
GOST IEC 60127-6 : 2013 | Identical |
NBN EN 60127-6 : 2014 | Identical |
NEN EN IEC 60127-6 : 2014 | Identical |
PN EN 60127-6 : 2015 | Identical |
BS EN 60127-6:2014 | Identical |
EN 60127-6:2014 | Identical |
NF EN 60127-6 : 2014 | Identical |
GOST R IEC 127-6 : 1999 | Identical |
NEN 10127-6 : 1994 AMD 1 1996 | Identical |
BIS IS/IEC 127-6 : 1994(R2007) | Identical |
UNE-EN 60127-6:2014 | Identical |
DIN EN 60127-6 : 2015 | Identical |
VDE 0820-6 : 2015 | Identical |
UNE-EN 60127-6:1997 | Identical |
SN EN 60127-6 : 2014 | Identical |
CEI EN 60127-6 : 2016 | Identical |
CSA E60335.2.55 : 2005 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-55: PARTICULAR REQUIREMENTS FOR ELECTRICAL APPLIANCES FOR USE WITH AQUARIUMS AND GARDEN PONDS |
CEI EN 60947-7-3 : 2011 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-3: ANCILLARY EQUIPMENT - SAFETY REQUIREMENTS FOR FUSE TERMINAL BLOCKS |
CEI EN 60127-10 : 2004 | MINIATURE FUSES - PART 10: USER GUIDE FOR MINIATURE FUSES |
NF EN 60127-7 : 2013 | MINIATURE FUSES - PART 7: MINIATURE FUSE-LINKS FOR SPECIAL APPLICATIONS |
10/30215969 DC : 0 | BS EN 60127-7 - MINIATURE FUSES - PART 7: MINIATURE FUSE-LINKS FOR SPECIAL APPLICATIONS |
I.S. EN 60127-10:2002 | MINIATURE FUSES - PART 10: USER GUIDE FOR MINIATURE FUSES |
I.S. EN 60947-7-3:2009 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-3: ANCILLARY EQUIPMENT - SAFETY REQUIREMENTS FOR FUSE TERMINAL BLOCKS |
AAMI ES60601-1 : 2005 : INC : AMD 1 : 2012 : R201200 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
AAMI ES60601-1 : 2005 : INC : AMD 2 : 2012 : R201200 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
AAMI ES60601-1 : 2005 : R2012 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
IEC 60335-2-78:2002+AMD1:2008 CSV | Household and similar electrical appliances - Safety - Part 2-78: Particular requirements for outdoor barbecues |
EN 60947-7-3:2009 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-3: ANCILLARY EQUIPMENT - SAFETY REQUIREMENTS FOR FUSE TERMINAL BLOCKS |
EN 12182:2012 | Assistive products for persons with disability - General requirements and test methods |
EN 60127-10:2002 | Miniature fuses - Part 10: User guide for miniature fuses |
A-A-55504 Revision E:2017 | FUSEHOLDER, EXTRACTOR POST, WHICH ACCOMMODATES 3AG (.25 INCH (IN) X 1.25 IN (6.35 MILLIMETERS (MM) X 31.75 MM)) OR .196 IN X .787 IN (5 MM X 20 MM) FUSE CARTRIDGES |
BS EN 60947-7-3:2009 | Low-voltage switchgear and controlgear Ancillary equipment. Safety requirements for fuse terminal blocks |
CSA E60335.2.55 : 2005 : R2013 | HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-55: PARTICULAR REQUIREMENTS FOR ELECTRICAL APPLIANCES FOR USE WITH AQUARIUMS AND GARDEN PONDS |
IEC 60127-10:2001 | Miniature fuses - Part 10: User guide for miniature fuses |
AAMI ES60601-1 : 2005 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
DIN EN 12182:2012-07 | Assistive products for persons with disability - General requirements and test methods |
EN 60065:2014/AC:2017-01 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016) |
I.S. EN 12182:2012 | ASSISTIVE PRODUCTS FOR PERSONS WITH DISABILITY - GENERAL REQUIREMENTS AND TEST METHODS |
14/30301133 DC : 0 | BS EN 60127-7:2014 - MINIATURE FUSES - PART 7: MINIATURE FUSE-LINKS FOR SPECIAL APPLICATIONS |
BS EN 60127-7:2016 | Miniature fuses Miniature fuse-links for special applications |
CSA C22.2 No. 60601.1 : 2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
BS EN 60127-1 : 2006 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
I.S. EN 60601- 1:2006&A1:2013&AC:2014&A12:2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
I.S. EN 60127-1:2006 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
UNE-EN 60601-1:2008 | Medical electrical equipment -- Part 1: General requirements for basic safety and essential performance |
UL 60947-7-3:3ED 2017-01 | Low-Voltage Switchgear and Controlgear - Part 7-3: Ancillary Equipment - Safety Requirements for Fuse Terminal Blocks |
UNI EN 12182 : 2012 | ASSISTIVE PRODUCTS FOR PERSONS WITH DISABILITY - GENERAL REQUIREMENTS AND TEST METHODS |
UNE-EN 60065:2015 | Audio, video and similar electronic apparatus - Safety requirements |
CSA C22.2 No. 60065 : 2016 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
I.S. EN 60065:2014 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
UNE-EN 60947-7-3:2011 | Low-voltage switchgear and controlgear -- Part 7-3: Ancillary equipment - Safety requirements for fuse terminal blocks |
BS EN 60601-1 : 2006 | MEDICAL ELECTRICAL EQUIPMENT PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
CAN/CSA-C22.2 No. 62841-1 : 2015 | ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY - SAFETY - PART 1: GENERAL REQUIREMENTS |
IEC 60947-7-3:2009 | Low-voltage switchgear and controlgear - Part 7-3: Ancillary equipment - Safety requirements for fuse terminal blocks |
IEC 60127-1:2006+AMD1:2011+AMD2:2015 CSV | Miniature fuses - Part 1: Definitions for miniature fuses andgeneral requirements for miniature fuse-links |
04/30106146 DC : DRAFT MARCH 2004 | BS EN 60601-1 - MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
BS EN 12182:2012 | Assistive products for persons with disability. General requirements and test methods |
I.S. EN 60127-7:2016 | MINIATURE FUSES - PART 7: MINIATURE FUSE-LINKS FOR SPECIAL APPLICATIONS |
BS EN 60127-10:2002 | Miniature fuses User guide for miniature fuses |
BS EN 60065 : 2014 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014, MODIFIED) |
CAN/CSA-C22.2 NO. 60947-7-3:17 | Low-voltage switchgear and controlgear ? Part 7-3: Ancillary equipment ? Safety requirements for fuse terminal blocks (Trinational standard NMX-J-538/7-3-ANCE with UL 60947-7-3) |
NF EN 60127-1 : 2006 AMD 2 2015 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
IEC 60335-2-55:2002+AMD1:2008 CSV | Household and similar electrical appliances - Safety - Part 2-55: Particular requirements for electrical appliances for use with aquariums and garden ponds |
IEC 60127-7:2015 | Miniature fuses - Part 7: Miniature fuse-links for special applications |
IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
EN 60127-7:2016 | Miniature fuses - Part 7: Miniature fuse-links for special applications |
EN 60127-1:2006/A2:2015 | MINIATURE FUSES - PART 1: DEFINITIONS FOR MINIATURE FUSES AND GENERAL REQUIREMENTS FOR MINIATURE FUSE-LINKS |
IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
IEC 60127-3:2015 | Miniature fuses - Part 3: Sub-miniature fuse-links |
IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
IEC 60050-212:2010 | International Electrotechnical Vocabulary (IEV) - Part 212: Electrical insulating solids, liquids and gases |
IEC 61210:2010 | Connecting devices - Flat quick-connect terminations for electrical copper conductors - Safety requirements |
ISO 3:1973 | Preferred numbers Series of preferred numbers |
IEC 60127-1:2006+AMD1:2011+AMD2:2015 CSV | Miniature fuses - Part 1: Definitions for miniature fuses andgeneral requirements for miniature fuse-links |
IEC 60695-2-13:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials |
IEC 60999-1:1999 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
IEC 60127-2:2014 | Miniature fuses - Part 2: Cartridge fuse-links |
IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
ISO 1302:2002 | Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation |
IEC 60068-2-47:2005 | Environmental testing - Part 2-47: Test - Mounting of specimens for vibration, impact and similar dynamic tests |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
IEC 60060-3:1976 | High-voltage test techniques - Part 3: Measuring devices |
IEC 60050-826:2004 | International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations |
IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
IEC 60068-3-4:2001 | Environmental testing - Part 3-4: Supporting documentation and guidance - Damp heat tests |
IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
IEC 60695-11-5 : 2.0 | FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE |
IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
IEC 60050-581:2008 | International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment |
IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.