BS 4500-1:1969
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
ISO limits and fits General, tolerances and deviations
Hardcopy , PDF
01-31-1990
English
08-31-1981
Gives standard tolerances and fundamental deviations for sizes from zero to 3150 mm; limits of tolerance for commonly used shafts and holes for general engineering purposes and for high precision work and horology; recommendations on selected fits. Explanation of system, terminology and definitions.
Committee |
TPR/1
|
DocumentType |
Standard
|
Pages |
0
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
BS 5773-6:1980 | Metric needle roller bearings Specification for tolerances of needle rollers. |
BS 4500B:1970 | ISO limits and fits Data sheet: selected ISO fits - shaft basis |
BS 1983-3:1987 | Chucks for machine tools and portable power tools Specification for dimensions of collet pads for base jaws of power operated workholding chucks |
BS 6600-1:1987 | Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment Specification for the outline dimensions of transformers and inductors using YEI-1 laminations |
BS 5000-50:1982 | Specification for rotating electrical machines of particular types or for particular applications Dimensions for oil burner motors |
BS 6590:1985 | Specification for capacity ratings and dimensions of power presses, mechanical open front type |
BS AU 214-3:1988 | Gearbox flanges Specification for dimensions for type S gearbox flanges for commercial vehicles and buses |
BS 4190:1967 | Specification for ISO metric black hexagon bolts, screws and nuts |
BS 6494-4:1989 | Hydraulic fluid power valve mounting surfaces. Specification for clamping dimensions of four-part, size 03 and 05, modular stack valves and directional control valves |
PD 6470:1981 | The management of design for economic production. Standardization philosophy aimed at improving the performance of the electrical and mechanical manufacturing sectors |
BS 6101-2:1991 | Machine tool ball screws Specification for accuracy, including geometrical tests |
BS 4500A:1970 | ISO limits and fits Data sheet: selected ISO fits - hole basis |
BS 5509:1977 | Specification for textile machinery and accessories - bearings for bottom rollers and allied dimensions - caps with central nose and caps with side lugs |
BS 6322-1:1982 | Tolerances for fasteners Specification for tolerances of bolts, screws and nuts with thread diameters ≥ 1.6 mm and ≤ 150 mm and product grades A, B and C |
BS 5912:1980 | Specification for dimensions of driving tenons and sockets for parallel shank drills and machine reamers |
BS 5621:1979 | Specification for dimensions of rotary masonry and rotary impact drills with hardmetal tips |
BS 4581-2:1984 | Flanges for mounting grinding wheels on grinding machine tools. Specification for dimensions and materials of flanges for grinding wheels of less than 76.2 mm bore |
BS 4825-3:1976 | Specification. Stainless steel pipes and fittings for the food industry. Clamp type couplings |
BS 799-7:1988 | Oil burning equipment Specification for dimensions of atomizing oil burner pumps with rotating shaft and external drive |
BS 4825-4:1977 | Specification for stainless steel pipes and fittings for the food industry Screwed type couplings |
BS 4185-13:1985 | Machine tool components Specification for dimensions of counterbored holes |
BS 7201-1:1989 | Hydraulic fluid power. Gas loaded accumulators Specification for seamless steel accumulator bodies above 0.5 L water capacity |
BS 5517:1977 | Specification for dimensions of metric long arbors and their accessories for milling machines |
BS 6494-1:1984 | Hydraulic fluid power valve mounting surfaces Specification for four-port directional control valves |
BS PP7308(1986) : 1986 | ENGINEERING DRAWING PRACTICE FOR SCHOOLS AND COLLEGES |
BS AU 214-2:1988 | Gearbox flanges Specification for dimensions for type A gearbox flanges for commercial vehicles and buses |
BS 6494-6:1989 | Hydraulic fluid power valve mounting surfaces Specification for pressure-control valves (excluding pressure-relief valves), sequence valves, unloading valves, throttle valves and check valves |
BS EN 2309:1990 | Specification for hole sizes for solid rivets |
BS 949-1:1992 | Screwing taps Specification of general dimensions |
BS 4481-1:1981 | Bonded abrasive products. Specification for general features of types of abrasive wheels, blocks, honing stones, segments and profiles |
BS 6276:1987 | Specification for dimensions and identification code for mounting flanges and shafts ends for hydraulic fluid power pumps and motors |
BS 122-3:1987 | Milling cutters Specification for milling cutters except screwed shank cutters |
BS 308-2:1985 | Engineering drawing practice Recommendations for dimensioning and tolerancing of size |
BS 5221:1987 | Specification for general purpose, metric module gear hobs |
BS 5045-2:1989 | Transportable gas containers Specification for steel containers of 0.5 L up to 450 L water capacity with welded seams |
BS 192:1982 | Specification for open-ended wrenches |
BS 3876-1:1990 | Rope rollers, pulleys, mountings and assemblies for colliery track haulage Specification for parallel barrel rollers, mountings and assemblies |
BS 6107-2:1987 | Rolling bearings: tolerances Specification for tolerances of radial bearings |
BS 4481-2:1983 | Bonded abrasive products Specification for dimensions of grinding wheels and segments |
BS 2485:1987 | Specification for tee slots, tee bolts, tee nuts and tenons |
BS 5045-1:1982 | Transportable gas containers Specification for seamless steel gas containers above 0.5 litre water capacity |
BS 2890:1989 | Specification for troughed belt conveyors |
BS 6168:1987 | Specification for non-metallic spur gears |
BS 3876-2:1990 | Rope rollers, pulleys, mountings and assemblies for colliery track haulage Specification for vertical spindle pulleys, mountings and assemblies |
BS 3555:1988 | Specification for ring wrenches |
BS 122-5:1986 | Milling cutters Specification for mounting dimensions and accessories |
BS 5501-1:1977 | Electrical apparatus for potentially explosive atmospheres General requirements |
BS 1936-2:1991 | Undercuts and runouts for screw threads Specification for ISO metric screw threads |
BS 328-1:1986 | Drills and reamers Specification for twist drills |
BS 5045-6:1987 | Transportable gas containers Specification for seamless containers of less than 0.5 litre water capacity |
BS 4999-147:1988 | General requirements for rotating electrical machines Specification for dimensions of brushes and brush-holders for electrical machinery |
BS 328-5:1983 | Drills and reamers Specification for the dimensions of countersinks and counterbores |
BS 328-3:1983 | Drills and reamers Specification for the dimensions of core drills |
BS 6487:1984 | Specification for split pin holes and wire holes in bolts, screws and studs |
BS 1660-3:1988 | Machine tapers Specification for turret sockets and reduction sleeves with tapped ends for tools with Morse taper shanks |
BS 5367:1976 | Dimensions of coated abrasives |
BS 5045-7:2000 | Transportable gas containers Specification for seamless steel gas containers of water capacity 0.5 L up to 15 L for special portable applications |
BS 3800-1:1990 | General tests for machine tools Code of practice for testing geometric accuracy of machines operating under no load or finishing conditions |
BS 4185-10:1977 | Machine tool components Trapezoidal threads for lead and feed screw assemblies |
BS 6881:1988 | Specification for construction and testing of miners\' caplamps in relation to the risk of explosion for mines susceptible to firedamp |
BS 4656-25:1980 | Accuracy of machine tools and methods of test Gear planing machines |
BS 5400-9.2:1983 | STEEL, CONCRETE AND COMPOSITE BRIDGES - BRIDGE BEARINGS - SPECIFICATION FOR MATERIALS, MANUFACTURE AND INSTALLATION OF BRIDGE BEARINGS |
BS 5594:1986 | Specification for leaf chains, clevises and sheaves |
BS 5242-1:1987 | Tubes for fluid power cylinder barrels Specification for steel tubes with specially finished surfaces |
BS 4235-1:1972 | Specification for metric keys and keyways Parallel and taper keys |
BS 6494-5:1989 | Hydraulic fluid power valve mounting surfaces Specification for compensated flow-control valves |
BS 6101-2:1982 | Machine tool ball screws Specification for accuracy, including geometrical tests |
BS 6053:1981 | Specification for outside diameters of conduits for electrical installations and threads for conduits and fittings |
DEFSTAN 02-304(PT1)/2(2002) : 2002 | SHAFTING SYSTEMS AND PROPULSORS - PART 1: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING |
BS 5461(1977) : LATEST | SPECIFICATION FOR ROTARY DIAMOND DRESSERS AND DIAMOND CHISEL AND CONE POINT TRUING TOOLS |
BS 6104-2:1983 | Mechanical properties of fasteners Specification for nuts with specified proof load values |
BS 5242-2:1983 | Tubes for fluid power cylinder barrels Specification for non-ferrous metallic tubes with specially finished bores |
BS 6186-1:1981 | Specification for straight cylindrical involute splines: metric module, side fit Dimensions and tolerances |
BS 4215-4:1987 | Resistance spot welding electrodes, electrode holders and ancillary equipment Specification for taper plug gauges and taper ring gauges |
BS 6101-6:1990 | Machine tool ball screws Specification for ball nuts and principal dimensions of ball screws |
BS 6554-1:1984 | Laminations for transformers and inductors for use in telecommunication and electronic equipment Specification for dimensions, mechanical characteristics and electrical testing |
NES 1023 : ISSUE 2 | INTERFERENCE FIT - OIL INJECTION METHOD |
BS 2518-2:1977 | Specification for rotary form relieved gear cutters Metric module |
BS 1098-2:1977 | Specification for jig bushes Metric units |
BS 6494-3:1989 | Hydraulic fluid power valve mounting surfaces Specification for pressure-relief valves |
BS CECC 75100:1984 | Harmonized system of quality assessment for electronic components. Sectional specification: two-part and edge socket connectors for printed board application |
BS 7333:1990 | Specification for slewing jib cranes |
BS 721-2:1983 | Specification for worm gearing Metric units |
BS 122-5:1978 | Milling cutters Mounting dimensions and accessories |
BS MA 82:1978 | Specification for shipbuilding - oil and water drain screws |
BS 3876-5:1990 | Rope rollers, pulleys, mountings and assemblies for colliery track haulage Specification for suspended pulley assemblies and clamps |
BS 1296-4:1978 | Specification for single point cutting tools Ground high speed steel tool bits |
BS AU 113c:1978 | Specification for dimensional characteristics of coupling ball for caravans and light trailers |
BS 5983-5:1982 | Metric spherical plain bearings Specification for dimensions and tolerances of spherical plain bearing rod ends, dimension series E and JK |
DEFSTAN 02-304(PT2)/2(2002) : 2002 | SHAFTING SYSTEMS AND PROPULSORS - PART 2: DESIGN REQUIREMENTS FOR MAIN PROPULSION SHAFTING AUXILIARIES |
BS 436-2:1970 | Spur and helical gears Basic rack form, modules and accuracy (1 to 50 metric module) |
PP 7309:1985 | AN INTRODUCTION TO THE TOLERANCING OF FUNCTIONAL LENGTH DIMENSIONS |
BS 4656-26:1980 | Accuracy of machine tools and methods of test Gear shaping machines |
BS 5655-8:1983 | Lifts and service lifts Specification for eyebolts for lift suspension |
BS 3673-4:1977 | Specification for spring retaining rings Carbon steel circlips - metric series |
BS 7228-5.1(1989) : 1989 | INDUSTRIAL ROBOTS - MECHANICAL INTERFACES - SPECIFICATION FOR CIRCULAR FORM (FORM A) |
BS 4186:1984 | Specification for clearance holes for metric bolts and screws |
BS 3856:1986 | Specification for slots in platens for projection welding machines |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.