BS EN 60214:1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
On-load tap-changers
Hardcopy , PDF
English
15-03-1998
03-07-2003
SECTION ONE - GENERAL
1 Scope
2 Service conditions
3 Information required with enquires and orders
SECTION TWO - DEFINITIONS
4 Definitions relating to on-load tap-changers (excluding
motor-drive mechanisms)
5 Definitions relating to motor-drive mechanisms
SECTION THREE - REQUIREMENTS FOR ON-LOAD TAP-CHANGERS
6 Rating
7 Design, construction and safety
8 Type tests
9 Routine tests
10 Nameplate and manufacturer's handbook
SECTION FOUR - REQUIREMENTS FOR MOTOR-DRIVE MECHANISMS FOR
ON-LOAD TAP-CHANGERS
11 Design, construction and safety
12 Type tests
13 Routine tests
14 Nameplate and manufacturer's handbook
APPENDIX A - Supplementary information on switching duty
relating to tap-changers with resistor
transition only
APPENDIX B - Method of determining the equivalent temperature
of the transition resistor using power pulse
currents
APPENDIX C - Simulated circuits for service duty and breaking
capacity tests
ANNEX ZA Normative references to international publications
with their corresponding European publications
Applicable to on-load tap-changers for power transformers together with their motor-drive mechanisms. Concerned chiefly to tap-changers immersed in transformer oil in accordance with IEC 296, but could be used for gas-insulated tap-changers where conditions apply.
| Committee |
PEL/14
|
| DevelopmentNote |
Supersedes BS 4571(1994) & 97/202553 DC (07/2003)
|
| DocumentType |
Standard
|
| Pages |
42
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN 60214 : 1998 | Identical |
| I.S. EN 60214:1999 | Identical |
| NBN EN 60214 : 1998 | Identical |
| IEC 60214:1989 | Identical |
| EN 60214:1997 | Identical |
| UNE-EN 60214:1999 | Identical |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| HD 398.1 : 200S1 | POWER TRANSFORMERS - GENERAL |
| HD 588.1 : S1 AMD 1 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS |
| IEC 60354:1991 | Loading guide for oil-immersed power transformers |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN 60060-2:2011 | High-voltage test techniques - Part 2: Measuring systems |
| IEC 60076-3:2013 | Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air |
| IEC 60137:2017 | Insulated bushings for alternating voltages above 1000 V |
| IEC 60076-1:2011 | Power transformers - Part 1: General |
| HD 398.3 : S1 AMD 1 | POWER TRANSFORMERS - INSULATION LEVELS AND DIELECTRIC TESTS |
| IEC 60144:1963 | Degrees of protection of enclosures for low-voltage switchgear and controlgear |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.