BS EN 62132-4:2006
Current
The latest, up-to-date edition.
Integrated circuits. Measurement of electromagnetic immunity. 150 kHz to 1 GHz Direct RF power injection method
Hardcopy , PDF
English
31-07-2006
1 Scope
2 Normative references
3 Terms and definitions
4 General
4.1 Measurement basics
4.2 Single pin direct power injection
4.3 Multiple pin direct power injection into
pins of differential mode systems
5 Test conditions
6 Test equipment
6.1 General
6.2 RF power source
6.3 RF power meter and directional coupler
7 Test set-up
7.1 General
7.2 Power injection set-up
7.3 Test circuit board
7.4 Characteristics of the power injection set-up
7.5 Decoupling networks
8 Test procedure
8.1 General
8.2 Specific test procedure
9 Test report
Annex A (informative) Example of a specification of
immunity levels e.g. for
automotive applications
Annex B (informative) Hints for the best installation
of a test set-up with respect
to RF
Annex C (informative) Constant peak test level explanation
Annex ZA (normative) Normative references to international
publications with their corresponding
European publications
Bibliography
Specifies a method to measure the immunity of integrated circuits (IC) in the presence of conducted RF disturbances, e.g. resulting from radiated RF disturbances.
| Committee |
EPL/47
|
| DevelopmentNote |
Supersedes 02/208194 DC. (07/2006)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
Describes a method to measure the immunity of integrated circuits (IC) in the presence of conducted RF disturbances, e.g. resulting from radiated RF disturbances. This method guarantees a high degree of repeatability and correlation of immunity measurements. This standard establishes a common base for the evaluation of semiconductor devices used in equipment functioning in an environment subject to unwanted radio frequency electromagnetic waves.
| Standards | Relationship |
| I.S. EN 62132-4:2006 | Identical |
| NF EN 62132-4 : 2006 | Identical |
| NBN EN 62132-4 : 2007 | Identical |
| EN 62132-4:2006 | Identical |
| IEC 62132-4:2006 | Identical |
| DIN EN 62132-4:2006-10 | Identical |
| UNE-EN 62132-4:2006 | Equivalent |
| ISO 11452-3:2016 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 3: Transverse electromagnetic (TEM) cell |
| ISO 11452-4:2011 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 4: Harness excitation methods |
| ISO 11451-3:2015 | Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 3: On-board transmitter simulation |
| EN 62132-1:2016 | Integrated circuits - Measurement of electromagnetic immunity - Part 1: General conditions and definitions |
| IEC 62132-1:2015 | Integrated circuits - Measurement of electromagnetic immunity - Part 1: General conditions and definitions |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| ISO 11898-1:2015 | Road vehicles — Controller area network (CAN) — Part 1: Data link layer and physical signalling |
| EN 61967-4 : 2002 COR 2017 | INTEGRATED CIRCUITS - MEASUREMENT OF ELECTROMAGNETIC EMISSIONS, 150 KHZ TO 1 GHZ - PART 4: MEASUREMENT OF CONDUCTED EMISSIONS - 1 OHM/150 OHM DIRECT COUPLING METHOD (IEC 61967-4:2002/COR1:2017) |
| IEC 61967-4:2002+AMD1:2006 CSV | Integrated circuits - Measurement of electromagnetic emissions, 150 kHz to 1 GHz - Part 4: Measurement of conducted emissions - 1 Ω/150 Ω direct coupling method |
| ISO 11452-2:2004 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 2: Absorber-lined shielded enclosure |
| ISO 11452-1:2015 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 1: General principles and terminology |
| ISO 11452-5:2002 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 5: Stripline |
| ISO 11451-2:2015 | Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 2: Off-vehicle radiation sources |
| ISO 11452-7:2003 | Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 7: Direct radio frequency (RF) power injection |
| ISO 11451-4:2013 | Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 4: Bulk current injection (BCI) |
| ISO 11451-1:2015 | Road vehicles — Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 1: General principles and terminology |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.