DIN EN 14364:2013-05
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
Hardcopy , PDF
01-08-2023
English, German
01-05-2013
National foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 General requirements
5 Pipes
6 Fittings
7 Joint performance
Annex A (normative) - Test method for the resistance
to bending and pressure of end-thrust loaded
joints in pipe systems
Bibliography
This standard is included in DIN Handbook 171, 13-5 and 259.
DevelopmentNote |
Supersedes DIN EN 1115-2. (05/2002) Supersedes DIN 19565-1, DIN 19565-1 E, DIN EN 1115-1, DIN EN 1115-1 E, DIN EN 1115-3, DIN EN 1115-3 E, DIN EN 1115-5, DIN EN 1115-5 E, DIN EN 1636-3, DIN EN 1636-3 E, DIN EN 1636-5 and DIN EN 1636-5 E. (07/2006)
|
DocumentType |
Standard
|
Pages |
73
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
NBN EN 14364 : 2013 | Identical |
NEN EN 14364 : 2013 | Identical |
NS EN 14364 : 2013 | Identical |
I.S. EN 14364:2013 | Identical |
SN EN 14364 : 2013 | Identical |
UNE-EN 14364:2015 | Identical |
BS EN 14364:2013 | Identical |
EN 14364:2013 | Identical |
NF EN 14364 : 2013 | Identical |
DIN HDBK 13-5 : 5ED 2015 | ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN |
DIN HDBK 259 : 4ED 2007 | ABWASSERTECHNIK 5 - ROHRE UND FORMSTUECKE FUER ABWASSERKANAELE UND ERDVERLEGTE ABWASSERLEITUNGEN |
DIN 16869-2:2014-12 | CENTRIFUGALLY CAST FILLED GLASS FIBRE REINFORCED UNSATURATED POLYESTER RESIN (UP-GF) PIPES - PART 2: GENERAL QUALITY REQUIREMENTS, TESTING |
DIN 1986-4:2019-08 | DRAINAGE SYSTEMS ON PRIVATE GROUND - PART 4: FIELDS OF APPLICATION OF SEWAGE PIPES AND FITTINGS OF DIFFERENT MATERIALS |
DIN 16869-1:2014-12 | CENTRIFUGALLY CAST FILLED GLASS FIBRE REINFORCED UNSATURATED POLYESTER RESIN (UP-GF) PIPES - PART 1: DIMENSIONS |
DIN HDBK 171 : 5ED 2015 | ROHRE, ROHRLEITUNGSTEILE UND ROHRVERBINDUNGEN AUS REAKTIONSHARZFORMSTOFFEN |
DIN 1986-4:2011-12 | DRAINAGE SYSTEMS ON PRIVATE GROUND - PART 4: FIELDS OF APPLICATION OF SEWAGE PIPES AND FITTINGS OF DIFFERENT MATERIALS |
ISO 8521:2009 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength |
EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
ISO 7432:2002 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals |
EN ISO 2078:1994/A1:2015 | TEXTILE GLASS - YARNS - DESIGNATION (ISO 2078:1993/AMD 1:2015) |
EN 681-1:1996/A3:2005 | ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER |
ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
ISO 7685:1998 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness |
EN ISO 527-4:1997 | PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES |
ISO/TR 10465-3:2007 | Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits |
ISO 10928:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use |
ISO 1452-3:2009 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 3: Fittings |
ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
CEN/TS 14632:2012 | Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity |
EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
ISO 527-5:2009 | Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites |
EN 1447:2009+A1:2010 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure |
ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
EN 476:2011 | General requirements for components used in drains and sewers |
ISO 8533:2003 | Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints |
ISO 2078:1993 | Textile glass Yarns Designation |
ISO 8483:2003 | Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints |
ISO 8513:2016 | Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength |
ISO 10468:2003 | Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor |
ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
ISO 10466:1997 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring deflection |
ISO 10471:2003 | Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions |
EN ISO 527-5:2009 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009) |
EN 1119:2009 | Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements |
EN ISO 1452-3:2010 | Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings (ISO 1452-3:2009, corrected version 2010-03-01) |
ISO 10952:2014 | Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition |
CEN/TS 14807:2013 | Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines |
ISO 2531:2009 | Ductile iron pipes, fittings, accessories and their joints for water applications |
CEN/TS 14578:2013 | Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.