ISO 4759-3:2016
Current
Current
The latest, up-to-date edition.
Tolerances for fasteners — Part 3: Washers for bolts, screws and nuts — Product grades A, C and F
Available format(s)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
French, English
Published date
01-06-2016
$142.98
Including GST where applicable
ISO 4759-3:2016 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts.
This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers.
It applies to non-captive and captive washers, and to standard and non-standard washers.
It does not apply to dynamic disc springs.
Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C.
NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances).
Annex A presents tolerances taken from ISO 286‑1 and ISO 286‑2.
| Committee |
ISO/TC 2
|
| DevelopmentNote |
Supersedes ISO/DIS 4759-3. (06/2016)
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| IS 15274 : 2021 | Identical |
| DIN EN ISO 4759-3:2016-12 | Identical |
| JIS B 1022:2018 | Identical |
| NF EN ISO 4759-3 : 2016 | Identical |
| NBN EN ISO 4759-3 : 1ED 2000 | Identical |
| NEN EN ISO 4759-3 : 2016 | Identical |
| NS EN ISO 4759-3 : 2000 | Identical |
| I.S. EN ISO 4759-3:2016 | Identical |
| AS 1237.2:2016 | Identical |
| PN EN ISO 4759-3 : 2016 | Identical |
| SS-EN ISO 4759-3:2016 | Identical |
| EN ISO 4759-3:2016 | Identical |
| DIN EN ISO 4759-3:2015-01 (Draft) | Identical |
| BS EN ISO 4759-3:2016 | Equivalent |
| GOST ISO 4759-3 : 2015 | Identical |
| GOST R ISO 4759-3 : 2009 | Identical |
| SAC GB/T 3103.3 : 2000 | Identical |
| BS EN ISO 4759-3:2016 | Identical |
| BS EN ISO 4759-3:2000 | Identical |
| UNE-EN ISO 4759-3:2017 | Identical |
| DIN 522:1990-03 | Similar to |
| BIS IS 15274 : 2003(R2014) | Identical |
| BS 6322-3:1992 | Identical |
| BS 6322-3:1982 | Identical |
| 03/319369 DC : DRAFT NOV 2003 | ISO 16047 - FASTENERS - TORQUE/CLAMP FORCE TESTING |
| PREN 3016 : 200P1 | AEROSPACE SERIES - WASHERS COUNTERSUNK, LOAD SPREADING - HEAT RESISTING STEEL |
| I.S. EN ISO 16047:2005 | FASTENERS - TORQUE/CLAMP FORCE TESTING (ISO 16047:2005) |
| I.S. EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| DIN EN ISO 10673:2009-10 | Plain washers for screw and washer assemblies - Small, normal and large series - Product grade A (ISO 10673:2009) |
| DIN EN ISO 10669:1999-11 | Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A (ISO 10669:1999); German version EN ISO 10669:1999 |
| BS EN 14399-5 : 2015-02 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| BS EN ISO 7089:2000 | Plain washers. Normal series. Product grade A |
| BS EN ISO 10673:2009 | Plain washers for screw and washer assemblies. Small, normal and large series. Product grade A |
| BS EN ISO 10669:1999 | Plain washers for tapping screw and washer assemblies. Normal and large series. Product grade A |
| BS EN ISO 7091:2000 | Plain washers. Normal series. Product grade C |
| DIN 7989-1:2001-04 | Washers for steel structures - Part 1: Product grade C |
| BS EN 3016:2008 | Aerospace series. Washers countersunk, load spreading. Heat resisting steel |
| DIN ISO 3269:1992-12 | FASTENERS - ACCEPTANCE INSPECTION |
| PREN 3017 : 200P1 | AEROSPACE SERIES - WASHERS, FACING/PACKING - HEAT RESISTING STEEL |
| I.S. EN 3017:2008 | AEROSPACE SERIES - WASHERS, FACING/PACKING - HEAT RESISTING STEEL |
| ISO 7415:1984 | Plain washers for high-strength structural bolting, hardened and tempered |
| ISO 7091:2000 | Plain washers — Normal series — Product grade C |
| DIN EN 14399-9:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| ISO 7092:2000 | Plain washers — Small series — Product grade A |
| BS EN 14399-1:2015 | High-strength structural bolting assemblies for preloading General requirements |
| DIN 34820:2004-05 | CHAMFERED PLAIN WASHERS FOR USE IN STRUCTURAL STEELWORK |
| I.S. EN 14399-6:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN ISO 10673:2009 | PLAIN WASHERS FOR SCREW AND WASHER ASSEMBLIES - SMALL, NORMAL AND LARGE SERIES - PRODUCT GRADE A |
| I.S. EN 14399-5:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| I.S. EN 14399-1:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| PREN 14399-9 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| BS EN 3017:2008 | Aerospace series. Washers, facing/packing. Heat resisting steel |
| ISO 13584-511:2006 | Industrial automation systems and integration — Parts library — Part 511: Mechanical systems and components for general use — Reference dictionary for fasteners |
| I.S. EN ISO 7091:2000 | PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C |
| DIN EN ISO 7093-1:2000-11 | PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A |
| ISO 7090:2000 | Plain washers, chamfered — Normal series — Product grade A |
| EN ISO 3269:2000 | Fasteners - Acceptance inspection (ISO 3269:2000) |
| I.S. EN ISO 7094:2000 | PLAIN WASHERS - EXTRA LARGE SERIES - PRODUCT GRADE C |
| I.S. EN 3016:2008 | AEROSPACE SERIES - WASHERS COUNTERSUNK, LOAD SPREADING - HEAT RESISTING STEEL |
| 08/30179025 DC : DRAFT MAR 2008 | BS EN ISO 10673 - PLAIN WASHERS FOR SCREW AND WASHER ASSEMBLIES - SMALL, NORMAL AND LARGE SERIES - PRODUCT GRADE A |
| DIN 7989-2:2001-04 | Washers for steel structures - Part 2: Product grade A |
| DIN 440:2001-03 | Washers with square hole for use in timber constructions |
| NF EN 3016 : 2008 | AEROSPACE SERIES - WASHERS COUNTERSUNK, LOAD SPREADING - HEAT RESISTING STEEL |
| 04/30123693 DC : DRAFT OCT 2004 | EN 15048-1 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| DIN EN 28738:1992-10 | PLAIN WASHERS FOR CLEVIS PINS - PRODUCT GRADE A |
| DIN EN ISO 7093-2:2000-11 | PLAIN WASHERS - LARGE SERIES - PART 2: PRODUCT GRADE C |
| BS EN 14399-6:2005 | High-strength structural bolting assemblies for preloading Plain chamfered washers |
| BS EN ISO 887:2000 | Plain washers for metric bolts, screws and nuts for general purposes. General plan |
| ISO 10673:2009 | Plain washers for screw and washer assemblies — Small, normal and large series — Product grade A |
| BS EN ISO 3269:2001 | Fasteners. Acceptance inspection |
| ISO 3269:2000 | Fasteners — Acceptance inspection |
| BS EN ISO 7090:2000 | Plain washers, chamfered. Normal series. Product grade A |
| ISO 7093-2:2000 | Plain washers — Large series — Part 2: Product grade C |
| ISO 8738:1986 | Plain washers for clevis pins — Product grade A |
| ISO 7093-1:2000 | Plain washers — Large series — Part 1: Product grade A |
| BS EN 28738:1992 | Plain washers for clevis pins. Product grade A |
| ISO 887:2000 | Plain washers for metric bolts, screws and nuts for general purposes — General plan |
| BS EN 14831:2005 | Fasteners. Tightening performance. Torque/Angle simplified test method |
| ISO 7089:2000 | Plain washers — Normal series — Product grade A |
| EN ISO 7089:2000 | Plain washers - Normal series - Product grade A (ISO 7089:2000) |
| EN 14399-1:2015 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| EN ISO 7093-2:2000 | Plain washers - Large series - Part 2: Product grade C (ISO 7093-2:2000) |
| EN ISO 7091:2000 | Plain washers - Normal series - Product grade C (ISO 7091:2000) |
| EN ISO 10673:2009 | Plain washers for screw and washer assemblies - Small, normal and large series - Product grade A (ISO 10673:2009) |
| EN 14399-9:2018 | High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indicators for bolt and nut assemblies |
| EN ISO 10669:1999 | Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A (ISO 10669:1999) |
| EN ISO 7090:2000 | Plain washers, chamfered - Normal series - Product grade A (ISO 7090:2000) |
| EN ISO 7092:2000 | Plain washers - Small series - Product grade A (ISO 7092:2000) |
| EN ISO 7093-1:2000 | Plain washers - Large series - Part 1: Product grade A (ISO 7093-1:2000) |
| EN 3016:2008 | Aerospace series - Washers countersunk, load spreading - Heat resisting steel |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| EN 3017:2008 | Aerospace series - Washers, facing/packing - Heat resisting steel |
| EN 28738:1992 | Plain washers for clevis pins - Product grade A (ISO 8738:1986) |
| EN 14831:2005 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| 15/30332554 DC : 0 | BS EN 14399-9 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| 05/30127446 DC : DRAFT JAN 2005 | ISO 13584-511 - INDUSTRIAL AUTOMATION SYSTEMS AND INTEGRATION - PARTS LIBRARY - PART 511: MECHANICAL SYSTEMS AND COMPONENTS FOR GENERAL USE - REFERENCE DICTIONARY FOR FASTENERS |
| BS EN ISO 16047 : 2005 | FASTENERS - TORQUE/CLAMP FORCE TESTING |
| BS EN 14399-9:2009 | High strength structural bolting for preloading System HR or HV. Direct tension indicators for bolt and nut assemblies |
| NF EN 3017 : 2008 | AEROSPACE SERIES - WASHERS, FACING/PACKING - HEAT RESISTING STEEL |
| I.S. EN 14399-9:2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-5:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| DIN EN 14399-1:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| DIN EN 14399-6:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| ISO 10669:1999 | Plain washers for tapping screw and washer assemblies — Normal and large series — Product grade A |
| DIN EN 14831:2005-07 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| DIN EN ISO 16047:2013-01 | Fasteners - Torque/clamp force testing (ISO 16047:2005 + Amd 1:2012) (includes Amendment :2012) |
| DIN EN ISO 887:2006-07 | Plain washers for metric bolts, screws and nuts for general purposes - General plan (ISO 887:2000 + Cor. 1:2006) |
| I.S. EN ISO 887:2000 | PLAIN WASHERS FOR METRIC BOLTS, SCREWS AND NUTS FOR GENERAL PURPOSES - GENERAL PLAN |
| UNE-EN 14399-5:2016 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| UNE-EN 14399-1:2016 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| UNE-EN 14399-6:2016 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| UNE-EN ISO 10673:2010 | Plain washers for screw and washer assemblies. Small, normal and large series. Product grade A (ISO 10673:2009) |
| ISO 2692:2014 | Geometrical product specifications (GPS) — Geometrical tolerancing — Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| ISO 286-2:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
Summarise
$142.98
Including GST where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.