NF EN 62149-5 : 2011
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FIBER OPTIC ACTIVE COMPONENTS AND DEVICES - PERFORMANCE STANDARDS - PART 5: ATM-PON TRANSCEIVERS WITH LD DRIVER AND CDR ICS
12-01-2013
09-11-2021
AVANT-PROPOS
INTRODUCTION
1 Domaine d'application
2 Références normatives
3 Termes, définitions et abréviations
3.1 Termes et définitions
3.2 Abréviations
4 Classification
5 Définition de produit
5.1 Description du module d'émetteur-récepteur
5.2 Description de forme appliquée
5.3 Schéma fonctionnel
5.4 Valeurs limites absolues
5.5 Spécification fonctionnelle
6 Essais
6.1 Essais de caractérisation
6.2 Essais de performance
7 Spécifications d'environnement
7.1 Sécurité générale
7.2 Sécurité du laser
7.3 Emission électromagnétique
Annexe A (normative) Mesure sur la tolérance au flux
énergétique réfléchi (Tableau 3,
Paramètre 13)
Annexe B (normative) Niveau logique du signal d'alarme et
du signal d'arrêt
Annexe ZA (normative) Références normatives à d'autres
publications internationales avec les
publications européennes correspondantes
Specifies standards on the transceiver modules for asynchronous-transfer-mode passive optical network (ATM-PON) systems recommended by the International Telecommunication Union (ITU) in Recommendation TG.983.1.
| DevelopmentNote |
Indice de classement: C93-884-5. PR NF EN 62149-5 September 2002. (10/2002) PR NF EN 62149-5 May 2008. (05/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 62149-5:2011 | Identical |
| NBN EN 62149-5 : 2011 | Identical |
| DIN EN 62149-5 : 2011 | Identical |
| I.S. EN 62149-5:2011 | Identical |
| IEC 62149-5:2009 | Identical |
| BS EN 62149-5:2011 | Identical |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| IEC 61300-2-17:2010 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-17: Tests - Cold |
| IEC 61753-1:2007 | Fibre optic interconnecting devices and passive components performance standard - Part 1: General and guidance for performance standards |
| IEC 61280-1-1:2013 | Fibre optic communication subsystem basic test procedures - Part 1-1: Test procedures for general communication subsystems - Transmitter output optical power measurement for single-mode optical fibre cable |
| IEC 61300-2-18:2005 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-18: Tests - Dry heat - High temperature endurance |
| IEC 61300-2-22:2007 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-22: Tests - Change of temperature |
| IEC TR 61931:1998 | Fibre optic - Terminology |
| IEC 61300-3-6:2008 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-6: Examinations and measurements - Return loss |
| IEC 61280-2-2:2012 | Fibre optic communication subsystem test procedures - Part 2-2: Digital systems - Optical eye pattern, waveform and extinction ratio measurement |
| IEC 61300-2-4:1995 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-4: Tests - Fibre/cable retention |
| IEC 61300-2-19:2012 | Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-19: Tests - Damp heat (steady state) |
| IEC 62150-2:2010 | Fibre optic active components and devices - Test and measurement procedures - Part 2: ATM-PON transceivers |