• There are no items in your cart

ASTM E 1486M : 2014 : REDLINE

Current

Current

The latest, up-to-date edition.

Standard Test Method for Determining Floor Tolerances Using Waviness, Wheel Path and Levelness Criteria (Metric)

Available format(s)

PDF

Language(s)

English

Published date

05-08-2014

CONTAINED IN VOL. 04.11, 2016 Defines data collection and analysis procedures to determine surface flatness and levelness by calculating waviness indices for survey lines and surfaces, elevation differences of defined wheel paths, and levelness indices using SI units.

Committee
E 06
DocumentType
Redline
Pages
13
PublisherName
American Society for Testing and Materials
Status
Current

1.1This test method covers data collection and analysis procedures to determine surface flatness and levelness by calculating waviness indices for survey lines and surfaces, elevation differences of defined wheel paths, and levelness indices using SI units.

Note 1This test method is the companion to inch-pound Test Method E1486.
Note 2This test method was not developed for, and does not apply to clay or concrete paver units.

1.1.1The purpose of this test method is to provide the user with floor tolerance estimates as follows:

1.1.1.1Local survey line waviness and overall surface waviness indices for floors based on deviations from the midpoints of imaginary chords as they are moved along a floor elevation profile survey line. End points of the chords are always in contact with the surface. The imaginary chords cut through any points in the concrete surface higher than the chords.

1.1.1.2Defined wheel path criteria based on transverse and longitudinal elevation differences, change in elevation difference, and root mean square (RMS) elevation difference.

1.1.1.3Levelness criteria for surfaces characterized by either of the following methods: the conformance of elevation data to the test section elevation data mean; or by the conformance of the RMS slope of each survey line to a specified slope for each survey line.

1.1.2The averages used throughout these calculations are the root mean squares, RMS (that is, the quadratic means). This test method gives equal importance to humps and dips, measured up (+) and down (−), respectively, from the imaginary chords.

1.1.3Appendix X1 is a commentary on this test method. Appendix X2 provides a computer program for waviness index calculations based on this test method.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM E 1486 : 2014 : REDLINE Standard Test Method for Determining Floor Tolerances Using Waviness, Wheel Path and Levelness Criteria
ACI 117M : 2010 SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY
ACI 117:2010 SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY
ASTM E 2351 : 2004 : REV A : R2013 Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Functionality (Withdrawn 2022)
ASTM E 2351 : 2004 Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Functionality
ASTM E 2351 : 2004 : REV A Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Functionality
ACI 117:2010(R2015) SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY
CSA A23.1 A23.2 : 2014 CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE

ASTM E 1486 : 2014 : REDLINE Standard Test Method for Determining Floor Tolerances Using Waviness, Wheel Path and Levelness Criteria

US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.