I.S. EN ISO 9093-2:2002
Superseded
View Superseded by
SMALL CRAFT - SEACOCKS AND THROUGH-HULL FITTINGS - PART 2: NON-METALLIC
Hardcopy , PDF
English
01-01-2002
07-23-2013
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Material requirements
5 Thread
6 Through-hull fittings - Requirements
7 Seacocks - Requirements
8 Hose fittings - Requirements
9 Drain plugs - Requirements
10 Installation
11 Manufacturers installation information
12 Owner's manual
13 Service manual
Annex A (normative) Strength test
Bibliography
Annex ZA (normative) Normative references to
international publications with their
relevant European publications
Annex ZB (informative) Clauses of this European
Standard addressing essential requirements
or other provisions of EU Directives
Defines requirements for the manufacture and installation of non-metallic through-hull fittings and/or assemblies comprising through-hull fittings, seacocks, hose fittings and/or drain plugs and components attached thereto, used in small craft of up to 24 m length of hull.
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN ISO 9093-2:2002 | Identical |
| NEN EN ISO 9093-2 : 2002 | Identical |
| NF EN ISO 9093-2 : 2003 | Identical |
| BS EN ISO 9093-2:2002 | Identical |
| ISO 9093-2:2002 | Identical |
| NS EN ISO 9093-2 : 1ED 2002 | Identical |
| DIN EN ISO 9093-2:2003-02 | Identical |
| NBN EN ISO 9093-2 : 2003 | Identical |
| UNE-EN ISO 9093-2:2003 | Identical |
| ISO 75-1:2013 | Plastics — Determination of temperature of deflection under load — Part 1: General test method |
| ISO 527-4:1997 | Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 527-5:2009 | Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| EN ISO 527-5:2009 | Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009) |
| ISO 75-3:2004 | Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics |
| ISO 527-3:1995 | Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.