ISO 11403-1:2014
Withdrawn
Withdrawn
View Superseded by
Plastics — Acquisition and presentation of comparable multipoint data — Part 1: Mechanical properties
Available format(s)
Hardcopy , PDF
Language(s)
English, French
Published date
06-06-2014
Withdrawn date
04-09-2025
Superseded by
US$96.00
Excluding Tax where applicable
ISO 11403-1:2014 specifies test procedures for the acquisition and presentation of multipoint data on the following mechanical properties of plastics:
- dynamic modulus;
- tensile properties at constant test speed;
- ultimate stress and strain;
- tensile stress-strain curves;
- tensile creep;
- Charpy impact strength;
- puncture impact behaviour.
| Committee |
ISO/TC 61/SC 2
|
| DevelopmentNote |
Supersedes ISO/FDIS 11403-1. (06/2014)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DIN EN ISO 11403-1:2003-09 | Identical |
| NF EN ISO 11403-1 : 2014 | Identical |
| NBN EN ISO 11403-1 : 2014 | Identical |
| NEN EN ISO 11403-1 : 2014 | Identical |
| NS EN ISO 11403-1 : 2014 | Identical |
| I.S. EN ISO 11403-1:2014 | Identical |
| PN EN ISO 11403-1 : 2014 | Identical |
| BS EN ISO 11403-1:2014 | Identical |
| EN ISO 11403-1:2014 | Identical |
| DIN EN ISO 11403-1:2014-09 | Identical |
| UNE-EN ISO 11403-1:2014 | Identical |
| BS ISO 11403-1 : AMD 10683 | Identical |
| 05/30132990 DC : DRAFT APR 2005 | ISO 20753 - PLASTICS - TEST SPECIMENS |
| BS ISO 20753 : 2008 | PLASTICS - TEST SPECIMENS |
| BS 2782-9.910B(1997) : 1997 AMD 13128 | METHODS OF TESTING PLASTICS - SAMPLING AND TEST SPECIMEN PREPARATION - THERMOPLASTIC MATERIALS - GENERAL PRINCIPLES, AND INJECTION MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS |
| BS ISO 1268-10:2005 | Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre compounds. General principles and moulding of multipurpose test specimens |
| I.S. EN ISO 20753:2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| EN ISO 899-1:2017 | Plastics - Determination of creep behaviour - Part 1: Tensile creep (ISO 899-1:2017) |
| DIN EN ISO 20753 E : 2014 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| I.S. EN ISO 899-1:2017 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP (ISO 899-1:2017) |
| ASTM D 5592 : 1994 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| DIN EN ISO 20753:2014-07 | PLASTICS - TEST SPECIMENS (ISO 20753:2008) |
| ASTM D 5939 : 1996 | Standard Test Method for Injection Moulding of Test Specimens of Thermoplatic Materials (Withdrawn 1998) |
| 16/30310691 DC : 0 | BS EN ISO 294-1 - PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS |
| BS ISO 27547-1:2010 | Plastics. Preparation of test specimens of thermoplastic materials using mouldless technologies General principles, and laser sintering of test specimens |
| ISO 20753:2008 | Plastics — Test specimens |
| EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| BS EN ISO 20753:2014 | Plastics. Test specimens |
| ISO 1268-11:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates |
| DIN EN ISO 10350-2:2011-06 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS |
| DIN EN ISO 295:2004-05 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004); German version EN ISO 295:2004 |
| I.S. EN ISO 294-1:2017 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| I.S. EN ISO 11403-3:2014 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| 02/121542 DC : DRAFT MAR 2002 | ISO/DIS 11403-2 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES |
| 08/30160325 DC : DRAFT MAR 2008 | BS ISO 27547-1 - PLASTICS - PREPARATION OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS USING MOULDLESS TECHNOLOGIES - PART 1: GENERAL PRINCIPLES, AND LASER-SINTERING OF SPECIMENS |
| BS ISO 11403-2 : 95 AMD 10691 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - THERMAL AND PROCESSING PROPERTIES |
| 01/121538 DC : DRAFT APRIL 2001 | BS EN ISO 899-1 PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP |
| BS ISO 1268-11:2005 | Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| BS ISO 10724-1 : 1998 AMD 13328 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS |
| ASTM D 5592 : 1994 : R2002 : EDT 1 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| SAE J2642_201707 | Recommended Practice for Developing Specifications for Automotive Thermoplastic Materials |
| ASTM D 5857 : 2017 : REDLINE | Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology |
| ISO 17282:2004 | Plastics — Guide to the acquisition and presentation of design data |
| DIN EN ISO 11403-3:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| BS EN ISO 10350-2:2011 | Plastics. Acquisition and presentation of comparable single-point data Long-fibre-reinforced plastics |
| EN ISO 10350-2:2011 | Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011) |
| I.S. EN ISO 294-3:2003 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - SMALL PLATES |
| EN ISO 294-3:2003 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 3: Small plates (ISO 294-3:2002) |
| I.S. EN ISO 10350-2:2011 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS |
| I.S. EN ISO 10350-1:2017 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017) |
| ASTM D 5935 : 1996 | Practice for Acquisition and Presentation of Comparable Single-Point Data (Withdrawn 1998) |
| ASTM D 5592 : 1994 : R2010 | Standard Guide for Material Properties Needed in Engineering Design Using Plastics |
| EN ISO 20753:2014 | Plastics - Test specimens (ISO 20753:2008) |
| ISO 1268-10:2005 | Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
| BS EN ISO 10724-2:2001 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) Small plates |
| ISO 11403-3:2014 | Plastics — Acquisition and presentation of comparable multipoint data — Part 3: Environmental influences on properties |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| BS EN ISO 294-3:2003 | Plastics. Injection moulding of test specimens of thermoplastic materials Small plates |
| BS EN ISO 295:2004 | Plastics. Compression moulding of test specimens of thermosetting materials |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| ISO 10350:1993 | Plastics — Acquisition and presentation of comparable single-point data |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| BS EN ISO 294-1:2017 | Plastics. Injection moulding of test specimens of thermoplastic materials General principles, and moulding of multipurpose and bar test specimens |
| EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
| EN ISO 10724-1:2001 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998) |
| EN ISO 10350-1:2017 | Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017) |
| EN ISO 10724-2:2000 | Plastics - Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) - Part 2: Small plates (ISO 10724-2:1998) |
| EN ISO 295:2004 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
| ISO 27547-1:2010 | Plastics — Preparation of test specimens of thermoplastic materials using mouldless technologies — Part 1: General principles, and laser sintering of test specimens |
| BS EN ISO 10350-1:2017 | Plastics. Acquisition and presentation of comparable single-point data Moulding materials |
| IEC TS 62600-2:2016 | Marine energy - Wave, tidal and other water current converters - Part 2: Design requirements for marine energy systems |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| BS EN ISO 10724-1:2001 | Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) General principles and moulding of multipurpose test specimens |
| BS EN ISO 11403-3:2014 | Plastics. Acquisition and presentation of comparable multipoint data Environmental influences on properties |
| DIN EN ISO 11403-3:2002-02 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014) |
| UNE-ISO 1268-10:2012 | Fibre-reinforced plastics. Methods of producing test plates. Part 10: Injection moulding of BMC and other long-fibre moulding compounds. General principles and moulding of multipurpose test specimens |
| UNE-ISO 1268-11:2012 | Fibre-reinforced plastics. Methods of producing test plates. Part 11: Injection moulding of BMC and other long-fibre moulding compounds. Small plates |
| UNE-EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
| UNE-EN ISO 11403-3:2014 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
| UNE-EN ISO 10350-2:2011 | Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011) |
| UNE-EN ISO 20753:2015 | Plastics - Test specimens (ISO 20753:2008) |
| ISO 6603-2:2000 | Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing |
| ISO 15850:2014 | Plastics — Determination of tension-tension fatigue crack propagation — Linear elastic fracture mechanics (LEFM) approach |
| ISO 6721-2:2008 | Plastics — Determination of dynamic mechanical properties — Part 2: Torsion-pendulum method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 294-3:2002 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates |
| ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 17281:2002 | Plastics — Determination of fracture toughness (GIC and KIC) at moderately high loading rates (1 m/s) |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 6721-4:2008 | Plastics — Determination of dynamic mechanical properties — Part 4: Tensile vibration — Non-resonance method |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 20753:2008 | Plastics — Test specimens |
| ISO 13586:2000 | Plastics — Determination of fracture toughness (GIC and KIC) — Linear elastic fracture mechanics (LEFM) approach |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.