ISO 1461:2009
Withdrawn
Withdrawn
View Superseded by
Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
Available format(s)
Hardcopy , PDF
Language(s)
English, French, Russian
Published date
05-07-2009
Withdrawn date
04-09-2025
Superseded by
US$96.00
Excluding Tax where applicable
ISO 1461:2009 specifies the general properties of coatings and test methods for coatings applied by dipping fabricated iron and steel articles (including certain castings) in a zinc melt (containing not more than 2 % of other metals). It does not apply to the following:
- sheet, wire and woven or welded mesh products that are continuously hot dip galvanized;
- tube and pipe that are hot dip galvanized in automatic plants;
- hot dip galvanized products (e.g. fasteners) for which specific standards exist and which might include additional requirements or requirements which are different from those of ISO 1461:2009.
After-treatment/over-coating of hot dip galvanized articles is not covered by ISO 1461:2009.
| Committee |
ISO/TC 107/SC 4
|
| DevelopmentNote |
Supersedes ISO/DIS 1461. (05/2009)
|
| DocumentType |
Standard
|
| Pages |
16
|
| ProductNote |
THIS STANDARD ALSO REFER-EN 10025
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| DS EN ISO 1461 : 2009 | Identical |
| NF EN ISO 1461 : 2009 | Identical |
| NBN EN ISO 1461 : 2009 | Identical |
| NEN EN ISO 1461 : 2009 | Identical |
| NS EN ISO 1461 : 2009 | Identical |
| I.S. EN ISO 1461:2009 | Identical |
| PN EN ISO 1461 : 2011 | Identical |
| SS-EN ISO 1461 : 2009 | Identical |
| EN ISO 1461:2009 | Identical |
| BS EN ISO 1461:2009 | Equivalent |
| DIN EN ISO 1461:2009-10 | Equivalent |
| UNE-EN ISO 1461:2010 | Identical |
| NS 1970 : 1983 | Identical |
| BS EN ISO 1461:2009 | Identical |
| NBN EN 24565 : 1993 | Identical |
| UNE 37501:1988 | Similar to |
| DIN EN ISO 1461 Beiblatt 1:1999-03 | Corresponds |
| DIN EN ISO 1461:2009-10 | Identical |
| DIN 50976:1989-05 | Similar to |
| DIN EN 13071-2:2013-12 | STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED AND BOTTOM EMPTIED - PART 2: ADDITIONAL REQUIREMENTS FOR UNDERGROUND OR PARTLY UNDERGROUND SYSTEMS |
| 12/30259649 DC : 0 | BS ISO 1891-2 - FASTENERS - TERMINOLOGY - PART 2: VOCABULARY AND DEFINITIONS FOR COATINGS |
| ISO 20340:2009 | Paints and varnishes — Performance requirements for protective paint systems for offshore and related structures |
| 11/30247279 DC : 0 | BS EN 1337-1 - STRUCTURAL BEARINGS - PART 1: GENERAL |
| DIN EN 124-3:2015-09 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 3: GULLY TOPS AND MANHOLE TOPS MADE OF STEEL OR ALUMINIUM ALLOYS |
| PD CEN/TS 16811-3:2015 | Winter maintenance equipment. De-icing agents Other solid and liquid de-icing agents. Requirements and test methods |
| 11/30239476 DC : 0 | BS EN 10025-2 - HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS |
| BS EN 45510-6-5:2000 | Guide for the procurement of power station equipment. Turbine auxiliaries Dry cooling systems - Section 5: Dry cooling systems |
| 10/30212123 DC : 0 | BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| DIN EN ISO 15589-2 E : 2014 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES (ISO 15589-2:2012) |
| EN ISO 2081:2018 | Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2018) |
| I.S. EN ISO 12944-5:2018 | PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 5: PROTECTIVE PAINT SYSTEMS (ISO 12944-5:2018) |
| BS ISO 799:2004 | Ships and marine technology. Pilot ladders |
| VDE 0212-2 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| DIN EN 10025-6:2011-04 (Draft) | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION |
| IEEE 1591.1-2012 | IEEE Standard for Testing and Performance of Hardware for Optical Ground Wire (OPGW) |
| BS EN ISO 12944-4:2017 | Paints and varnishes. Corrosion protection of steel structures by protective paint systems Types of surface and surface preparation |
| BS EN 60168:1995 | Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000V |
| 04/30055611 DC : 0 | BS EN 124 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS |
| 15/30325000 DC : 0 | BS EN 10305-5 - STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 5: WELDED COLD SIZED SQUARE AND RECTANGULAR TUBES |
| PREN 845-1 : DRAFT 2012 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| BS EN 50216-10:2009 | Power transformer and reactor fittings Oil-to-air heat exchangers |
| 08/30175210 DC : DRAFT APR 2008 | BS EN 15773 - INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED AND SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
| DIN EN 12496:2014-02 | Galvanic anodes for cathodic protection in seawater and saline mud |
| 10/30212126 DC : 0 | BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
| PREN 12574-2 : DRAFT 2015 | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| CEI EN 61897 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR STOCKBRIDGE TYPE AEOLIAN VIBRATION DAMPERS |
| BS EN 14490:2010 | Execution of special geotechnical works. Soil nailing |
| 11/30239488 DC : 0 | BS EN 10025-6 - HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN QUENCHED AND TEMPERED CONDITIONS |
| DIN EN 10025-4:2011-04 (Draft) | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 4: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| PREN 50119 : DRAFT 2017 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| 15/30323520 DC : 0 | BS EN 12574-2 - STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| IEEE 1591.2-2017 | IEEE Standard for Testing and Performance of Hardware for All-Dielectric Self-Supporting (ADSS) Fiber Optic Cable |
| CEI EN 61537 : 2007 | CABLE MANAGEMENT - CABLE TRAY SYSTEMS AND CABLE LADDER SYSTEMS |
| PREN 840-5 : DRAFT 2010 | MOBILE WASTE CONTAINERS - PART 5: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| DIN EN 16927 E : 2017 | MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS |
| 17/30358108 DC : 0 | BS EN 17125 - DOMESTIC SPAS AND HOT TUBS - SAFETY REQUIREMENTS AND TEST METHODS |
| I.S. EN 16927:2017 | MINI-POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI-POOLS |
| API 560 : 2016 | FIRED HEATERS FOR GENERAL REFINERY SERVICE |
| I.S. EN 1090-2:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| I.S. EN 61325:1997 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1000 V - CERAMIC OR GLASS INSULATOR UNITS FOR D.C. SYSTEMS - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| I.S. EN 1474-1:2008 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| ISO 1823:2015 | Rubber hose and hose assemblies for oil suction and discharge service — Specification |
| 15/30320416 DC : 0 | BS EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| BS EN 50341-1:2012 | Overhead electrical lines exceeding AC 1 kV General requirements. Common specifications |
| PREN 13914-1 : DRAFT 2013 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING |
| ISO 5480:1979 | Shipbuilding — Guardrails for cargo ships |
| BS EN ISO 12944-6:2018 | Paints and varnishes. Corrosion protection of steel structures by protective paint systems Laboratory performance test methods |
| BS EN ISO 2081:2018 | Metallic and other inorganic coatings. Electroplated coatings of zinc with supplementary treatments on iron or steel |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| NF EN 50164-2 : 2008 | LIGHTNING PROTECTION COMPONENTS (LPC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| I.S. EN 15773:2018 | INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
| DIN EN ISO 2081:2016-04 (Draft) | METALLIC AND OTHER INORGANIC COATINGS - ELECTROPLATED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENTS ON IRON OR STEEL |
| EN ISO 12944-9:2018 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 9: Protective paint systems and laboratory performance test methods for offshore and related structures (ISO 12944-9:2018) |
| I.S. EN 13071-1:2008 | STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED AND BOTTOM EMPTIED - PART 1: GENERAL REQUIREMENTS |
| DIN EN 12574-2:2015-08 (Draft) | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| DIN EN 12899-2:2008-02 | Fixed, vertical road traffic signs - Part 2: Transilluminated traffic bollards (TTB) |
| DIN EN 1317-5:2012-06 | Road restraint systems - Part 5: Product requirements and evaluation of conformity for vehicle restraint systems (includes Amendment A2:2012) |
| DIN EN 1473:2016-10 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| BS EN 12574-2:2017 | Stationary waste containers Performance requirements and test methods |
| BS EN 845-2 : 2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
| BS EN 10223-2:2012 | Steel wire and wire products for fencing and netting Hexagonal steel wire netting for agricultural, insulation and fencing purposes |
| BS EN 517:2006 | Prefabricated accessories for roofing. Roof safety hooks |
| BS EN 10025-2:2004 | Hot rolled products of structural steels Technical delivery conditions for non-alloy structural steels |
| BS EN 1765:2004 | Rubber hose assemblies for oil suction and discharge services. Specification for the assemblies |
| BS EN 1995-1-1 : 2012 | EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS |
| BS EN 10305-2:2016 | Steel tubes for precision applications. Technical delivery conditions Welded cold drawn tubes |
| IEC 60383-1:1993 | Insulators for overhead lines with a nominal voltage above 1000 V - Part 1: Ceramic or glass insulator units for a.c. systems - Definitions, test methods and acceptance criteria |
| BS EN 12811-2:2004 | Temporary works equipment Information on materials |
| BS EN ISO 7384:1995 | Corrosion tests in artificial atmospheres. General requirements |
| BS EN 10025-3:2004 | Hot rolled products of structural steels Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| DIN EN 10305-1:2016-08 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 1: SEAMLESS COLD DRAWN TUBES |
| EN 61897:1998 | Overhead lines - Requirements and tests for Stockbridge type aeolian vibration dampers |
| 14/30244780 DC : 0 | BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION |
| I.S. EN ISO 13705:2012 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FIRED HEATERS FOR GENERAL REFINERY SERVICE (ISO 13705:2012) |
| I.S. EN 10305-2:2016 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 2: WELDED COLD DRAWN TUBES |
| VDE 0212-3 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR STOCKBRIDGE TYPE AEOLIAN VIBRATION DAMPERS |
| I.S. EN 10223-7:2012 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 7: STEEL WIRE WELDED PANELS FOR FENCING |
| EN 62561-2:2012 | Lightning Protection System Components (LPSC) - Part 2: Requirements for conductors and earth electrodes |
| EN 12811-2:2004 | Temporary works equipment - Part 2: Information on materials |
| EN 12496:2013 | Galvanic anodes for cathodic protection in seawater and saline mud |
| EN 60383-1:1996/A11:1999 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1 KV - CERAMIC OR GLASS INSULATOR UNITS FOR A.C. SYSTEMS - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| EN 10305-3:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes |
| EN 10223-8:2013 | Steel wire and wire products for fencing and netting - Part 8: Welded mesh gabion products |
| EN 1123-3:2004 | Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems - Part 3: Dimensions and special requirements for vacuum drainage systems and for drainage systems in ship-building |
| EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas - Design requirements, type testing, marking, quality control |
| EN 10223-7:2012 | Steel wire and wire products for fencing and netting - Part 7: Steel wire welded panels for fencing |
| EN 124-4:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 4: Gully tops and manhole tops made of steel reinforced concrete |
| EN 62155:2003 | Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V |
| EN 12574-2:2017 | Stationary waste containers - Part 2: Performance requirements and test methods |
| EN 13411-1:2002+A1:2008 | Terminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings |
| EN 12899-1:2007 | Fixed, vertical road traffic signs - Part 1: Fixed signs |
| EN 10305-5:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 5: Welded cold sized square and rectangular tubes |
| EN 12899-2:2007 | Fixed, vertical road traffic signs - Part 2: Transilluminated traffic bollards (TTB) |
| EN 124-3:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 3: Gully tops and manhole tops made of steel or aluminium alloys |
| EN 10223-2:2012 | Steel wire and wire products for fencing and netting - Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes |
| EN 10305-2:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 2: Welded cold drawn tubes |
| EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| DIN EN 10025-4:2005-02 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 4: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| EN 62271-202:2014/AC:2014 | HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 202: HIGH-VOLTAGE/LOW-VOLTAGE PREFABRICATED SUBSTATION (IEC 62271-202:2014) |
| EN 61284:1997 | Overhead lines - Requirements and tests for fittings |
| DIN EN 10025-6:2009-08 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION |
| DIN EN 1090-2:2011-10 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| CEN/TS 16811-3:2015 | Winter service equipment and products - De-icing agents - Part 3: Other solid and liquid de-icing agents - Requirements and test methods |
| EN 10223-4:2012 | Steel wire and wire products for fencing and netting - Part 4: Steel wire welded mesh fencing |
| EN 13438:2013 | Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
| PREN 10025-3 : DRAFT 2011 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| BS ISO 5489:2008 | Ships and marine technology. Embarkation ladders |
| BS EN 61854:1998 | Overhead lines. Requirements and tests for spacers |
| PREN ISO 13705 : DRAFT 2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FIRED HEATERS FOR GENERAL REFINERY SERVICE |
| 10/30165662 DC : 0 | BS ISO 13706 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AIRCOOLED HEAT EXCHANGERS |
| I.S. EN 12329:2000 | CORROSION PROTECTION OF METALS - ELECTRODEPOSITED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENT ON IRON OR STEEL |
| S.R. 82:2017 | SLATING AND TILING - CODE OF PRACTICE |
| BS EN 14545:2008 | Timber structures. Connectors. Requirements |
| I.S. EN ISO 2081:2018 | METALLIC AND OTHER INORGANIC COATINGS - ELECTROPLATED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENTS ON IRON OR STEEL (ISO 2081:2018) |
| BS EN 62155:2003 | Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1000 V |
| ISO 17613-1:2006 | Manually operated pumps for drinking water — Selection and acceptance — Part 1: Southeast Asia |
| 03/317246 DC : 0 | ISO 2081 - METALLIC COATINGS - ELECTROPLATED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENTS ON IRON OR STEEL |
| 16/30323507 DC : 0 | BS EN 15773 - INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
| BS EN 10223-8:2013 | Steel wire and wire products for fencing and netting Welded mesh gabion products |
| BS EN 50397-2:2009 | Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV AC and not exceeding 36 kV AC Accessories for covered conductors. Tests and acceptance criteria |
| 16/30327440 DC : 0 | BS EN ISO 12944-3 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE COATING SYSTEMS - PART 3: DESIGN CONSIDERATIONS |
| PREN 711 : DRAFT 2015 | INLAND NAVIGATION VESSELS - RAILINGS FOR DECKS AND SIDE DECKS - REQUIREMENTS, TYPES |
| 08/30189610 DC : 0 | BS EN 10223-4 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 4: STEEL WIRE WELDED MESH FENCING |
| 17/30341013 DC : DRAFT AUG 2017 | BS EN 50119 - RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| 11/30215604 DC : 0 | BS IEC 60913 - RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| 16/30337293 DC : 0 | BS EN ISO 12944-9 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 9: PROTECTIVE PAINT SYSTEMS AND LABORATORY PERFORMANCE TEST METHODS FOR OFFSHORE AND RELATED STRUCTURES |
| 01/122577 DC : DRAFT JUNE 2001 | BS EN 1765 - RUBBER HOSE ASSEMBLIES FOR OIL SUCTION AND DISCHARGE SERVICES - SPECIFICATION FOR THE ASSEMBLIES |
| PREN 1317-5 : DRAFT 2013 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS, TEST AND ASSESSMENT METHODS AND ACCEPTANCE CRITERIA |
| BS ISO 5480:1979 | Shipbuilding. Guardrails for cargo ships |
| EN 60168:1994/A2:2000 | TESTS ON INDOOR AND OUTDOOR POST INSULATORS OF CERAMIC MATERIAL OR GLASS FOR SYSTEMS WITH NOMINAL VOLTAGES GREATER THAN 1KV |
| CEI EN 62155 : 2004 | HOLLOW PRESSURIZED AND UNPRESSURIZED CERAMIC AND GLASS INSULATORS FOR USE IN ELECTRICAL EQUIPMENT WITH RATED VOLTAGES GREATER THAN 1000 V |
| 07/30166781 DC : 0 | BS EN 50164-2 AMD 2 - LIGHTNING PROTECTION COMPONENTS (LPC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| BS EN 16927:2017 | Mini-pools. Specific requirements including safety and test methods for mini-pools |
| 15/30324994 DC : 0 | BS EN 10305-3 - STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 3: WELDED COLD SIZED TUBES |
| NF EN 62155 : 2003 | HOLLOW PRESSURIZED AND UNPRESSURIZED CERAMIC AND GLASS INSULATORS FOR USE IN ELECTRICAL EQUIPMENT WITH RATED VOLTAGES GREATER THAN 1000 V |
| 17/30360728 DC : DRAFT MAY 2017 | BS EN ISO 2081 - METALLIC AND OTHER INORGANIC COATINGS - ELECTROPLATED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENTS ON IRON OR STEEL |
| 07/30174613 DC : 0 | BS ISO 20340 - PAINTS AND VARNISHES - PERFORMANCE REQUIREMENTS FOR PROTECTIVE PAINT SYSTEMS FOR OFFSHORE AND RELATED STRUCTURES |
| I.S. EN ISO 12944-6:2018 | PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 6: LABORATORY PERFORMANCE TEST METHODS (ISO 12944-6:2018) |
| 12/30265307 DC : 0 | BS EN 124-4 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 4: GULLY TOPS AND MANHOLE TOPS MADE FROM STEEL REINFORCED CONCRETE |
| PREN 1090-2 : DRAFT 2015 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| BS EN 61897:1999 | Overhead lines. Requirements and tests for Stockbridge type aeolian vibration dampers |
| BS MA 92:1981 | Specification for pilot ladders |
| I.S. EN 10025-6:2004 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION |
| CEI EN 62561-2 : 2013 | LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| DIN EN 10025-2:2011-04 (Draft) | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS |
| I.S. EN 62561-2:2012 | LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES (IEC 62561-2:2012 (MOD)) |
| DIN EN 10025-3:2011-04 (Draft) | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| EN IEC 61730-1:2018/AC:2018-06 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2016) |
| BS EN 10025-4:2004 | Hot rolled products of structural steels Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| CEI EN 61284 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| EN IEC 62688:2018 | Concentrator photovoltaic (CPV) modules and assemblies - Safety qualification |
| 18/30369304 DC : DRAFT APR 2018 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| CEI EN 61325 : 1998 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1000 V CERAMIC OR GLASS INSULATOR UNITS FOR D.C. SYSTEMS DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| CEI EN 61854 : 2000 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| NF EN 50397-2 : 2010 | COVERED CONDUCTORS FOR OVERHEAD LINES AND THE RELATED ACCESSORIES FOR RATED VOLTAGES ABOVE 1 KV AC AND NOT EXCEEDING 36 KV AC - PART 2: ACCESSORIES FOR COVERED CONDUCTORS - TESTS AND ACCEPTANCE CRITERIA |
| BS EN 14592 : 2008 | TIMBER STRUCTURES - DOWEL-TYPE FASTENERS - REQUIREMENTS |
| I.S. EN 61897:1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR STOCKBRIDGE TYPE AEOLIAN VIBRATION DAMPERS |
| I.S. EN 10223-8:2013 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 8: WELDED MESH GABION PRODUCTS |
| I.S. EN 62271-202:2014 | HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 202: HIGH-VOLTAGE/LOW-VOLTAGE PREFABRICATED SUBSTATION |
| PREN 10348-2 : DRAFT 2016 | STEEL FOR THE REINFORCEMENT OF CONCRETE - GALVANIZED REINFORCING STEEL - PART 2: GALVANIZED REINFORCING STEEL PRODUCTS |
| ISO 7061:2015 | Ships and marine technology — Aluminium shore gangways for seagoing vessels |
| ISO 8678:1988 | Cup head square neck bolts with small head and short neck — Product grade B |
| I.S. EN 50164-2:2008 | LIGHTNING PROTECTION COMPONENTS (LPC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| DIN EN 13071-1:2008-10 | STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED BOTTOM EMPTIED - PART 1: GENERAL REQUIREMENTS |
| BS EN 10025-6:2019 | Hot rolled products of structural steels Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| EN 50341-1:2012 | Overhead electrical lines exceeding AC 1 kV - Part 1: General requirements - Common specifications |
| I.S. EN 50216-10:2009 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 10: OIL-TO-AIR HEAT EXCHANGERS |
| DIN EN 1090-2:2015-07 (Draft) | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| I.S. EN 50119:2009 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| ISO 14657:2005 | Zinc-coated steel for the reinforcement of concrete |
| DIN EN 12899-1:2008-02 | FIXED VERTICAL ROAD TRAFFIC SIGNS - PART 1: FIXED SIGNS |
| DIN EN 13438:2013-12 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDISED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
| DIN EN 14475:2006-04 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - REINFORCED FILL |
| BS EN 840-5:2012 | Mobile waste and recycling containers Performance requirements and test methods |
| DIN EN 10305-3:2016-08 | Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes |
| BS EN 13280:2001 | Specification for glass fibre reinforced cisterns of one-piece and sectional construction, for the storage, above ground, of cold water |
| BS EN 12329:2000 | Corrosion protection of metals. Electrodeposited coatings of zinc with supplementary treatment on iron or steel |
| EN 61854:1998 | Overhead lines - Requirements and tests for spacers |
| ISO 5620-1:1992 | Shipbuilding and marine structures — Filling connection for drinking water tanks — Part 1: General requirements |
| ISO 19859:2016 | Gas turbine applications — Requirements for power generation |
| BS EN 1473:2016 | Installation and equipment for liquefied natural gas. Design of onshore installations |
| IEC 61897:1998 | Overhead lines - Requirements and tests for Stockbridge type aeolian vibration dampers |
| BS EN 1462:2004 | Brackets for eaves gutters. Requirements and testing |
| I.S. EN 10305-5:2016 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 5: WELDED COLD SIZED SQUARE AND RECTANGULAR TUBES |
| I.S. EN 1462:2004 | BRACKETS FOR EAVES GUTTERS - REQUIREMENTS AND TESTING |
| I.S. EN 10149-3:2013 | HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED OR NORMALIZED ROLLED STEELS |
| DIN EN 12329:2000-09 | CORROSION PROTECTION OF METALS - ELECTRODEPOSITED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENT ON IRON AND STEEL |
| DIN EN 1473:1997-11 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| I.S. EN 12574-2:2017 | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| I.S. EN 1317-5:2007 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS |
| I.S. EN 40-5:2002 | LIGHTING COLUMNS - PART 5: REQUIREMENTS FOR STEEL LIGHTING COLUMNS |
| DIN EN 12574-2:2017-05 | STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| I.S. EN 10223-2:2012 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 2: HEXAGONAL STEEL WIRE NETTING FOR AGRICULTURAL, INSULATION AND FENCING PURPOSES |
| I.S. EN 10149-2:2013 | HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 2: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICALLY ROLLED STEELS |
| I.S. EN 711:2016 | INLAND NAVIGATION VESSELS - RAILINGS FOR DECKS AND SIDE DECKS - REQUIREMENTS, DESIGNS AND TYPES |
| I.S. EN 13411-1:2002 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 1: THIMBLES FOR STEEL WIRE ROPE SLINGS |
| DIN EN 61897 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR STOCKBRIDGE TYPE AEOLIAN VIBRATION DAMPERS |
| I.S. EN 517:2006 | PREFABRICATED ACCESSORIES FOR ROOFING - ROOF SAFETY HOOKS |
| I.S. EN 13438:2013 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR HOT DIP GALVANISED OR SHERARDISED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
| I.S. EN 845-2:2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
| I.S. EN 10223-4:2012 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 4: STEEL WIRE WELDED MESH FENCING |
| I.S. EN 1473:2016 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| I.S. EN 12899-1:2007 | FIXED, VERTICAL ROAD TRAFFIC SIGNS - PART 1: FIXED SIGNS |
| I.S. EN 516:2006 | PREFABRICATED ACCESSORIES FOR ROOFING - INSTALLATIONS FOR ROOF ACCESS - WALKWAYS, TREADS AND STEPS |
| I.S. EN 1765:2016 | RUBBER HOSE ASSEMBLIES FOR OIL SUCTION AND DISCHARGE SERVICES - SPECIFICATION FOR THE ASSEMBLIES |
| I.S. EN ISO 13706:2011 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AIR-COOLED HEAT EXCHANGERS (ISO 13706:2011) |
| I.S. EN 10305-1:2016 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 1: SEAMLESS COLD DRAWN TUBES |
| I.S. EN 10305-3:2016 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 3: WELDED COLD SIZED TUBES |
| I.S. EN 13914-1:2016 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING |
| I.S. EN 10255:2004 | NON-ALLOY STEEL TUBES SUITABLE FOR WELDING AND THREADING - TECHNICAL DELIVERY CONDITIONS |
| I.S. EN 845-1:2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| VDE 0446-5 : 1996 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1000 V - CERAMIC OR GLASS INSULATOR UNITS FOR DC SYSTEMS - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| VDE 0674-1:2001-12 | TESTS ON INDOOR AND OUTDOOR POST INSULATORS OF CERAMIC MATERIAL OR GLASS FOR SYSTEMS WITH NOMINAL VOLTAGES GREATER THAN 1 KV |
| DIN EN 61284:1998-05 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| VDI 3822 Blatt 1.6:2010-11 | Failure analysis - Liquid metal induced crack growth by hot dip galvanising |
| DIN EN 61325 : 1996 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1000 V - CERAMIC OR GLASS INSULATOR UNITS FOR D.C. SYSTEMS - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| VDE 0446-1 : 97 COR 1 2001 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1 KV - PART 1: CERAMIC OR GLASS INSULATOR UNITS FOR A.C. SYSTEMS - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| DIN EN 16927:2017-05 | MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS |
| BS 6180:2011 | Barriers in and about buildings. Code of practice |
| DIN EN 60168:2001-12 | TESTS ON INDOOR AND OUTDOOR POST INSULATORS OF CERAMIC MATERIAL OR GLASS FOR SYSTEMS WITH NOMINAL VOLTAGES GREATER THAN 1 KV |
| VDE 0212-1:1998-05 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| VDI 2579:2008-05 | Emission control - Hot-dip zinc galvanizing plants |
| DIN EN 60383-1 : 97 COR 1 2001 | INSULATORS FOR OVERHEAD LINES WITH A NOMINAL VOLTAGE ABOVE 1 KV - PART 1: CERAMIC OR GLASS INSULATOR UNITS FOR A.C. SYSTEMS - DEFINITIONS, TEST METHODS AND ACCEPTANCE CRITERIA |
| CEI UNI EN 45510-6-5 : 2000 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 6-5: TURBINE AUXILIARIES - DRY COOLING SYSTEMS |
| PREN 10305-5 : DRAFT 2015 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 5: WELDED COLD SIZED SQUARE AND RECTANGULAR TUBES |
| 11/30239479 DC : 0 | BS EN 10025-3 - HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED/NORMALIZED ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| DIN EN 1474-1:2009-03 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| 16/30332608 DC : DRAFT JAN 2016 | BS EN 10210-2 - HOT FINISHED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| BS EN 124-4:2015 | Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of steel reinforced concrete |
| PREN 1473 : DRAFT 2018 | INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| 16/30329239 DC : 0 | BS EN ISO 2081 - METALLIC AND OTHER INORGANIC COATINGS - ELECTROPLATED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENTS ON IRON OR STEEL |
| BS ISO 15589-2 : 2012 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES |
| API 536 : 2017 | POST-COMBUSTION NO[X] CONTROL FOR FIRED EQUIPMENT IN GENERAL REFINERY AND PETROCHEMICAL SERVICES |
| 10/30232896 DC : 0 | BS ISO 15589-2 - PETROLEUM AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES |
| DIN EN 61854 : 1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| API 537 CHINESE : 2008 | FLARE DETAILS FOR GENERAL REFINERY AND PETROCHEMICAL SERVICE |
| 15/30326949 DC : 0 | BS EN 62561-2 ED. 2 - LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| BS EN 124-3:2015 | Gully tops and manhole tops for vehicular and pedestrian areas Gully tops and manhole tops made of steel or aluminium alloys |
| 12/30265304 DC : 0 | BS EN 124-3 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 3: GULLY TOPS AND MANHOLE TOPS MADE FROM STEEL OR ALUMINIUM ALLOY |
| PREN 10025-4 : DRAFT 2011 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 4: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| 13/30265750 DC : 0 | BS EN 13914-1 - DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING |
| BS ISO 7061:2015 | Ships and marine technology. Aluminium shore gangways for seagoing vessels |
| 12/30265756 DC : 0 | BS EN 845-1 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| 12/30256073 DC | BS EN 12899-3 AMD1. Fixed, vertical road traffic signs. Part 3. Delineator posts and retroreflectors |
| 97/100665 DC : DRAFT JAN 1997 | PREN 12725 - GLASS IN BUILDING - GLASS BLOCK WALLS - DESIGN, DIMENSIONS AND PERFORMANCE |
| EN 1473:2016 | Installation and equipment for liquefied natural gas - Design of onshore installations |
| I.S. EN 10025-2:2004 | Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels |
| 07/30174359 DC : DRAFT NOV 2007 | BS EN 62561-2 - LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| 11/30239482 DC : 0 | BS EN 10025-4 - HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 4: TECHNICAL DELIVERY CONDITIONS FOR THERMOMECHANICAL ROLLED WELDABLE FINE GRAIN STRUCTURAL STEELS |
| BS EN 61537:2007 | Cable management. Cable tray systems and cable ladder systems |
| 06/30133250 DC : 0 | BS EN 13071-1 - STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED BOTTOM EMPTIED - PART 1: GENERAL REQUIREMENTS |
| 14/30304016 DC : 0 | BS ISO 7061 - SHIPS AND MARINE TECHNOLOGY - ALUMINIUM SHORE GANGWAYS FOR SEAGOING VESSELS |
| 02/711527 DC : DRAFT SEP 2002 | ISO 10684 - FASTENERS - HOT DIP GALVANIZED COATINGS |
| BS ISO 17613-1:2006 | Manually operated pumps for drinking water. Selection and acceptance Southeast Asia |
| 03/116049 DC : DRAFT NOV 2003 | BS EN 12574-2 - STATIONARY WASTE CONTAINERS - PART 2: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| 15/30317833 DC : 0 | BS EN 711 - INLAND NAVIGATION VESSELS - RAILINGS FOR DECKS AND SIDE DECKS - REQUIREMENTS, TYPES |
| EN ISO 12944-5:2018 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems (ISO 12944-5:2018) |
| 07/30166095 DC : 0 | EN 124 - GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS |
| DIN EN 10149-3:2013-12 | HOT ROLLED FLAT PRODUCTS MADE OF HIGH YIELD STRENGTH STEELS FOR COLD FORMING - PART 3: TECHNICAL DELIVERY CONDITIONS FOR NORMALIZED OR NORMALIZED ROLLED STEELS |
| BS EN 60383-1:1998 | Insulators for overhead lines with a nominal voltage above 1000 V Ceramic or glass insulator units for a.c. systems. Definitions, test methods and acceptance criteria |
| BS EN 61325:1996 | Insulators for overhead lines with a nominal voltage above 1000 V. Ceramic or glass insulator units for d.c systems. Definitions, test methods and acceptance criteria |
| BS EN ISO 14713-2:2009 | Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures Hot dip galvanizing |
| ISO 5489:2008 | Ships and marine technology — Embarkation ladders |
| 05/30127458 DC : DRAFT JAN 2005 | ISO 13705 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FIRED HEATERS FOR GENERAL REFINERY SERVICE |
| I.S. EN ISO 15589-2:2014 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES (ISO 15589-2:2012) |
| PREN 1337-1 : DRAFT 2018 | STRUCTURAL BEARINGS - PART 1: GENERAL |
| NFP 22 501-1 : 98 XP | EXECUTION OF STEEL STRUCTURES - PART 1: GENERAL RULES AND RULES FOR BUILDINGS |
| API 17G:2006 | RECOMMENDED PRACTICE FOR COMPLETION/WORKOVER RISERS |
| IEC 61730-1:2016 | Photovoltaic (PV) module safety qualification - Part 1: Requirements for construction |
| ISO 2081:2018 | Metallic and other inorganic coatings — Electroplated coatings of zinc with supplementary treatments on iron or steel |
| API 17G : 2006 : R2011 | RECOMMENDED PRACTICE FOR COMPLETION/WORKOVER RISERS |
| PREN 10210-2 : DRAFT 2016 | HOT FINISHED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| I.S. EN 13071-2:2008 | STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED AND BOTTOM EMPTIED - PART 2: ADDITIONAL REQUIREMENTS FOR UNDERGROUND OR PARTLY UNDERGROUND SYSTEMS |
| I.S. EN 61854:1999 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR SPACERS |
| I.S. EN 16582-1:2015 | DOMESTIC SWIMMING POOLS - PART 1: GENERAL REQUIREMENTS INCLUDING SAFETY AND TEST METHODS |
| I.S. EN ISO 12944-9:2018 | PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 9: PROTECTIVE PAINT SYSTEMS AND LABORATORY PERFORMANCE TEST METHODS FOR OFFSHORE AND RELATED STRUCTURES (ISO 12944-9:2018) |
| I.S. EN 61537:2007 | CABLE MANAGEMENT - CABLE TRAY SYSTEMS AND CABLE LADDER SYSTEMS |
| EN IEC 62561-2:2018 | Lightning protection system components (LPSC) - Part 2: Requirements for conductors and earth electrodes |
| EN ISO 12944-3:2017 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 3: Design considerations (ISO 12944-3:2017) |
| I.S. EN 50341-1:2012 | OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS |
| I.S. EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| PREN 17125 : DRAFT 2017 | DOMESTIC SPAS AND HOT TUBS - SAFETY REQUIREMENTS AND TEST METHODS |
| CEI EN 50341-1 : 2013 | OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS |
| NACE SP 01 15 : 2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES |
| BS EN 13071-1:2008 | Stationary waste containers up to 5000 l, top lifted and bottom emptied General requirements |
| NF EN 61284 : 2000 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR FITTINGS |
| PREN 10025-2 : DRAFT 2011 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS |
| EN 1090-2:2008+A1:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| ISO 10721-2:1999 | Steel structures — Part 2: Fabrication and erection |
| PREN 10255 : DRAFT 2010 | NON-ALLOY STEEL TUBES SUITABLE FOR WELDING AND THREADING - TECHNICAL DELIVERY CONDITIONS |
| BS EN 1090-2 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| EN ISO 12944-6:2018 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 6: Laboratory performance test methods (ISO 12944-6:2018) |
| ISO 7412:1984 | Hexagon bolts for high-strength structural bolting with large width across flats (short thread length) — Product grade C — Property classes 8.8 and 10.9 |
| ISO 799:2004 | Ships and marine technology — Pilot ladders |
| IEC 62155:2003 | Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V |
| IEC 62561-2:2018 | Lightning protection system components (LPSC) - Part 2: Requirements for conductors and earth electrodes |
| I.S. EN 15644:2009 | TRADITIONALLY DESIGNED PREFABRICATED STAIRS MADE OF SOLID WOOD - SPECIFICATIONS AND REQUIREMENTS |
| EN ISO 14713-2:2009 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
| DIN EN 1462:2004-12 | Brackets for eaves gutters - Requirements and testing; German version EN 1462:2004 |
| DIN EN 1433:2005-09 | DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY |
| DIN EN 10223-4:2013-02 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 4: STEEL WIRE WELDED MESH FENCING |
| DIN EN 13914-1:2016-09 | DESIGN, PREPARATION AND APPLICATION OF EXTERNAL RENDERING AND INTERNAL PLASTERING - PART 1: EXTERNAL RENDERING |
| DIN EN 10223-2:2013-02 | Steel wire and wire products for fencing and netting - Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes |
| BS EN ISO 13705:2012 | Petroleum, petrochemical and natural gas industries. Fired heaters for general refinery service |
| BS EN 14475:2006 | Execution of special geotechnical works. Reinforced fill |
| BS EN ISO 5620-1:1997 | Shipbuilding and marine structures. Filling connection for drinking water tanks General requirements |
| DIN EN 10305-2:2016-08 | STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 2: WELDED COLD DRAWN TUBES |
| BS EN 10305-5:2010 | Steel tubes for precision applications. Technical delivery conditions Welded and cold sized square and rectangular tubes |
| BS EN 12899-2:2007 | Fixed, vertical road traffic signs Transilluminated traffic bollards (TTB) |
| BS EN 12325-2:1999 | Irrigation techniques. Centre pivot and moving lateral systems Minimum performances and technical characteristics |
| BS EN 13283:2002 | Zinc and zinc alloys. Secondary zinc |
| BS EN 711:2016 | Inland navigation vessels. Railings for decks and side decks. Requirements, designs and types |
| ISO 16904:2016 | Petroleum and natural gas industries — Design and testing of LNG marine transfer arms for conventional onshore terminals |
| BS EN 13411-1 : 2002 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 1: THIMBLES FOR STEEL WIRE ROPE SLINGS |
| DIN EN 10305-5:2016-08 | Steel tubes for precision applications - Technical delivery conditions - Part 5: Welded cold sized square and rectangular tubes |
| ISO 15749-1:2004 | Ships and marine technology — Drainage systems on ships and marine structures — Part 1: Sanitary drainage-system design |
| EN 1474-1:2008 | Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms |
| EN 13914-1:2016 | Design, preparation and application of external rendering and internal plastering - Part 1: External rendering |
| ISO 12944-3:2017 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 3: Design considerations |
| I.S. EN 124-4:2015 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 4: GULLY TOPS AND MANHOLE TOPS MADE OF STEEL REINFORCED CONCRETE |
| BS EN ISO 15589-2:2014 | Petroleum, petrochemical and natural gas industries. Cathodic protection of pipeline transportation systems Offshore pipelines |
| I.S. EN 1995-1-1:2005 | EUROCODE 5: DESIGN OF TIMBER STRUCTURES - PART 1-1: GENERAL - COMMON RULES AND RULES FOR BUILDINGS |
| DIN EN 124-4:2015-09 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 4: GULLY TOPS AND MANHOLE TOPS MADE OF STEEL REINFORCED CONCRETE |
| NF EN ISO 14713-2 : 2010 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
| ISO 12944-4:2017 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 4: Types of surface and surface preparation |
| DIN EN 14490:2010-11 | Execution of special geotechnical works - Soil nailing |
| PREN 13438 : DRAFT 2012 | PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR GALVANIZED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
| 12/30260570 DC : 0 | BS EN 50341-1 - OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS |
| BS MA 85:1979 | Specification for shipbuilding - filling connection for drinking water tanks on ships |
| BS EN 50164-2:2008 | Lightning protection components (LPC) Requirements for conductors and earth electrodes |
| BS 6917:1987 | Method for corrosion testing in artificial atmospheres: general principles |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| BS EN ISO 14713-1:2017 | Zinc coatings. Guidelines and recommendations for the protection against corrosion of iron and steel in structures General principles of design and corrosion resistance |
| BS EN 12496:2013 | Galvanic anodes for cathodic protection in seawater and saline mud |
| 15/30325003 DC : 0 | BS EN 10305-2 - STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 2: WELDED COLD DRAWN TUBES |
| PREN 10223-4 : DRAFT 2008 | STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 4: STEEL WIRE WELDED MESH FENCING |
| 08/30189619 DC : 0 | BS EN 10223-7 - STEEL WIRE AND WIRE PRODUCTS FOR FENCES - PART 7: STEEL WIRE WELDED PANELS FOR FENCING |
| BS EN 45510-6-6:2000 | Guide for the procurement of power station equipment. Turbine auxiliaries Turbine auxiliaries. Wet and wet/dry cooling towers - Section 6: Wet/dry cooling towers |
| DIN EN ISO 14713-1:2010-05 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017) |
| 05/30134192 DC : DRAFT MAY 2005 | EN 516 - PREFABRICATED ACCESSORIES FOR ROOFING - INSTALLATIONS FOR ROOF ACCESS - WALKWAYS, TREADS AND STEPS |
| NF ENV 1090-1 : 96 FD | EXECUTION OF STEEL STRUCTURES - PART 1: GENERAL RULES AND RULES FOR BUILDINGS |
| 01/713202 DC : DRAFT SEP 2001 | ISO/DIS 15589-2 - PETROLEUM AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION FOR PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES |
| 06/30133254 DC : 0 | BS EN 13071-2 - STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED BOTTOM EMPTIED - PART 2: ADDITIONAL REQUIREMENTS FOR UNDERGROUND OR PARTLY UNDERGROUND SYSTEMS |
| BS EN 61284:1998 | Overhead lines. Requirements and tests for fittings |
| 17/30358594 DC : 0 | BS ISO 799-1 - SHIPS AND MARINE TECHNOLOGY - PILOT LADDERS - PART 1: DESIGN AND SPECIFICATION |
| BS EN 16582-1:2015 | Domestic swimming pools General requirements including safety and test methods |
| 13/30227963 DC : 0 | BS ISO 1823 - RUBBER HOSE ASSEMBLIES FOR OIL SUCTION AND DISCHARGE SERVICE - SPECIFICATION |
| BS EN ISO 1891-2:2014 | Fasteners. Terminology Vocabulary and definitions for coatings |
| BS EN 1474-1:2008 | Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer arms |
| 16/30234880 DC : 0 | BS EN ISO 12944-5 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 5: PROTECTIVE PAINT SYSTEMS |
| 04/30095062 DC : 0 | ISO 5489 - SHIPS AND MARINE TECHNOLOGY - EMBARKATION LADDERS |
| DD ENV 1090-1:1998 | Execution of steel structures General rules and rules for buildings (together with United Kingdom national application document) |
| BS EN 50119 : 2009 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| BS 5649-4:1982 | Lighting columns Recommendations for surface protection of metal lighting columns |
| DIN EN 14592:2012-07 | Timber structures - Dowel-type fasteners - Requirements (includes Amendment A1:2012) |
| CEI UNI EN 45510-6-6 : 2000 | GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 6-6: TURBINE AUXILIARIES - WET AND WET/DRY COOLING TOWERS |
| PREN 14592 : DRAFT 2017 | TIMBER STRUCTURES - DOWEL-TYPE FASTENERS - REQUIREMENTS |
| BS ISO 1823:2015 | Rubber hose and hose assemblies for oil suction and discharge service. Specification |
| 18/30365863 DC : 0 | BS EN 1337-1 - STRUCTURAL BEARINGS - PART 1: GENERAL |
| 13/30278077 DC : 0 | BS EN ISO 16904 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND TESTING OF LNG MARINE TRANSFER ARMS FOR CONVENTIONAL ONSHORE TERMINALS |
| 10/30232452 DC : 0 | BS EN 840-5 - MOBILE WASTE CONTAINERS - PART 5: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| 15/30324991 DC : 0 | BS EN 10305-1 - STEEL TUBES FOR PRECISION APPLICATIONS - TECHNICAL DELIVERY CONDITIONS - PART 1: SEAMLESS COLD DRAWN TUBES |
| API 2RD : 2013 | DYNAMIC RISERS FOR FLOATING PRODUCTION SYSTEMS |
| API 661 : 2015 | PETROLEUM, PETROCHEMICAL, AND NATURAL GAS INDUSTRIES - AIR-COOLED HEAT EXCHANGERS |
| API 17G : 2006 : R2016 | RECOMMENDED PRACTICE FOR COMPLETION/WORKOVER RISERS |
| EN ISO 1891-2:2014 | Fasteners - Terminology - Part 2: Vocabulary and definitions for coatings (ISO 1891-2:2014) |
| DIN EN 10149-2:2013-12 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| DIN EN 10223-8:2014-04 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 8: WELDED MESH GABION PRODUCTS |
| I.S. EN ISO 12944-4:2017 | PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 4: TYPES OF SURFACE AND SURFACE PREPARATION (ISO 12944-4:2017) |
| PREN 10025-6 : DRAFT 2011 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN QUENCHED AND TEMPERED CONDITIONS |
| IWA 14-2:2013 | Vehicle security barriers — Part 2: Application |
| I.S. EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| S.R. CWA 16221:2010 | VEHICLE SECURITY BARRIERS - PERFORMANCE REQUIREMENTS, TEST METHODS AND GUIDANCE ON APPLICATION |
| PREN 845-2 : DRAFT 2012 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
| NF EN 1090-2 : 2009 + A1 2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| BS EN ISO 12944-3:2017 | Paints and varnishes. Corrosion protection of steel structures by protective paint systems Design considerations |
| BS EN 13071-2 : 2008 | STATIONARY WASTE CONTAINERS UP TO 5000 L, TOP LIFTED AND BOTTOM EMPTIED - PART 2: ADDITIONAL REQUIREMENTS FOR UNDERGROUND OR PARTLY UNDERGROUND SYSTEMS |
| EN ISO 12944-4:2017 | Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 4: Types of surface and surface preparation (ISO 12944-4:2017) |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| I.S. EN 14592:2008 | TIMBER STRUCTURES - DOWEL-TYPE FASTENERS - REQUIREMENTS |
| I.S. EN ISO 12944-3:2017 | PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 3: DESIGN CONSIDERATIONS (ISO 12944-3:2017) |
| I.S. EN 14490:2010 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - SOIL NAILING |
| IEC 60913:2013 | Railway applications - Fixed installations - Electric traction overhead contact lines |
| ISO 4775:1984 | Hexagon nuts for high-strength structural bolting with large width across flats — Product grade B — Property classes 8 and 10 |
| I.S. EN 62155:2003 | HOLLOW PRESSURIZED AND UNPRESSURIZED CERAMIC AND GLASS INSULATORS FOR USE IN ELECTRICAL EQUIPMENT WITH RATED VOLTAGES GREATER THAN 1000 V |
| I.S. EN 14545:2008 | TIMBER STRUCTURES - CONNECTORS - REQUIREMENTS |
| IEC 61854:1998 | Overhead lines - Requirements and tests for spacers |
| DIN EN 840-5:2013-02 | MOBILE WASTE AND RECYCLING CONTAINERS - PART 5: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| DIN EN 10223-7:2013-02 | STEEL WIRE AND WIRE PRODUCTS FOR FENCING AND NETTING - PART 7: STEEL WIRE WELDED PANELS FOR FENCING |
| DIN EN 711:2016-09 | Inland navigation vessels - Railings for decks and side decks - Requirements, designs and types |
| ISO 14713-2:2009 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 2: Hot dip galvanizing |
| ONORM EN ISO 14713-2 : 2010 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
| BS EN 845-1 : 2013 | SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 1: WALL TIES, TENSION STRAPS, HANGERS AND BRACKETS |
| IEC 61325:1995 | Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic or glass insulator units for d.c. systems - Definitions, test methods and acceptance criteria |
| BS EN 10255:2004 | Non-alloy steel tubes suitable for welding and threading. Technical delivery conditions |
| BS EN ISO 10684:2004 | Fasteners. Hot dip galvanized coatings |
| BS EN ISO 13628-7:2006 | Petroleum and natural gas industries. Design and operation of subsea production systems Completion/workover riser systems |
| ISO 14713-1:2017 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance |
| BS EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming Technical delivery conditions for thermomechanically rolled steels |
| ISO 13628-7:2005 | Petroleum and natural gas industries — Design and operation of subsea production systems — Part 7: Completion/workover riser systems |
| BS EN 13101:2002 | Steps for underground man entry chambers. Requirements, marking, testing and evaluation of conformity |
| EN 840-5:2012 | Mobile waste and recycling containers - Part 5: Performance requirements and test methods |
| I.S. EN 50119:2020 | Railway applications - Fixed installations - Electric traction overhead contact lines |
| BS EN 124:1994 | Gully tops and manhole tops for vehicular and pedestrian areas. Design requirements, type testing, marking, quality control |
| BS EN 10223-7:2012 | Steel wire and wire products for fencing and netting Steel wire welded panels for fencing |
| BS EN 13914-1:2016 | Design, preparation and application of external rendering and internal plastering External rendering |
| I.S. EN 840-5:2012 | MOBILE WASTE AND RECYCLING CONTAINERS - PART 5: PERFORMANCE REQUIREMENTS AND TEST METHODS |
| ISO 13706:2011 | Petroleum, petrochemical and natural gas industries — Air-cooled heat exchangers |
| ISO 25457:2008 | Petroleum, petrochemical and natural gas industries — Flare details for general refinery and petrochemical service |
| ISO 10684:2004 | Fasteners — Hot dip galvanized coatings |
| ISO 13705:2012 | Petroleum, petrochemical and natural gas industries — Fired heaters for general refinery service |
| BS EN 10305-3:2016 | Steel tubes for precision applications. Technical delivery conditions Welded cold sized tubes |
| IEC 61537:2006 | Cable management - Cable tray systems and cable ladder systems |
| BS ISO 19859:2016 | Gas turbine applications. Requirements for power generation |
| BS EN 14396:2004 | Fixed ladders for manholes |
| IEC 62271-202:2014 | High-voltage switchgear and controlgear - Part 202: High-voltage/ low-voltage prefabricated substation |
| ISO 7384:1986 | Corrosion tests in artificial atmosphere — General requirements |
| BS EN 13438:2013 | Paints and varnishes. Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
| BS EN 10305-1:2016 | Steel tubes for precision applications. Technical delivery conditions Seamless cold drawn tubes |
| ISO 1891-2:2014 | Fasteners — Terminology — Part 2: Vocabulary and definitions for coatings |
| BS EN 516:2006 | Prefabricated accessories for roofing. Installations for roof access. Walkways, treads and steps |
| EN 50119 : 2009 AMD 1 2013 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| 16/30242287 DC : 0 | BS EN 62688 - CONCENTRATOR PHOTOVOLTAIC (CPV) MODULE AND ASSEMBLY SAFETY QUALIFICATION |
| BS EN 1317-5 : 2007 | ROAD RESTRAINT SYSTEMS - PART 5: PRODUCT REQUIREMENTS AND EVALUATION OF CONFORMITY FOR VEHICLE RESTRAINT SYSTEMS |
| BS EN 10223-4:2012 | Steel wire and wire products for fencing and netting Steel wire welded mesh fencing |
| BS EN 1123-1:1999 | Pipes and fittings of longitudinally welded hot-dip galvanized steel pipes with spigot and socket for waste water systems Requirements, testing, quality control |
| DIN EN 12676-1:2003-08 | Anti-glare systems for roads - Part 1: Performance and characteristics (includes Amendment A1:2003); German version EN 12676-1:2000 + A1:2003 |
| EN 14592:2008+A1:2012 | Timber structures - Dowel-type fasteners - Requirements |
| EN 845-2:2013+A1:2016 | Specification for ancillary components for masonry - Part 2: Lintels |
| EN 845-1:2013+A1:2016 | Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets |
| EN ISO 13706:2011 | Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011) |
| EN 1462:2004 | Brackets for eaves gutters - Requirements and testing |
| EN ISO 7384:1995 | Corrosion test in artificial atmosphere - General requirements (ISO 7384:1986) |
| EN 13280:2001 | Specification for glass fibre reinforced cisterns of one piece and sectional construction, for the storage, above ground, of cold water |
| EN 40-5:2002 | Lighting columns - Part 5: Requirements for steel lighting columns |
| EN ISO 15589-2:2014 | Petroleum, petrochemical and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines (ISO 15589-2:2012) |
| BS EN 1433:2002 | Drainage channels for vehicular and pedestrian areas. Classification, design and testing requirements, marking and evaluation of conformity |
| EN 14490:2010 | Execution of special geotechnical works - Soil nailing |
| EN ISO 25457:2008 | Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service (ISO 25457:2008) |
| EN ISO 16904:2016 | Petroleum and natural gas industries - Design and testing of LNG marine transfer arms for conventional onshore terminals (ISO 16904:2016) |
| EN ISO 15749-1:2004 | Ships and marine technology - Drainage systems on ships and marine structures - Part 1: Sanitary drainage-system design (ISO 15749-1:2004) |
| EN ISO 5620-1:1996 | Shipbuilding and marine structures - Filling connection for drinking water tanks - Part 1: General requirements (ISO 5620-1:1992) |
| EN ISO 13628-7:2006 | Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover riser systems (ISO 13628-7:2005) |
| EN 14545:2008 | Timber structures - Connectors - Requirements |
| EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
| EN 1765:2016 | Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies |
| EN 15644:2008 | Traditionally designed prefabricated stairs made of solid wood - Specifications and requirements |
| EN 711:2016 | Inland navigation vessels - Railings for decks and side decks - Requirements, designs and types |
| EN 516:2006 | Prefabricated accessories for roofing - Installations for roof access - Walkways, treads and steps |
| EN ISO 14713 : 1999 | PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - ZINC AND ALUMINIUM COATINGS - GUIDELINES |
| EN 517:2006 | Prefabricated accessories for roofing - Roof safety hooks |
| EN 16927:2017 | Mini-pools - Specific requirements including safety and test methods for mini-pools |
| EN ISO 13705:2012 | Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012) |
| EN 14396:2004 | Fixed ladders for manholes |
| I.S. EN IEC 62561-2:2018 | LIGHTNING PROTECTION SYSTEM COMPONENTS (LPSC) - PART 2: REQUIREMENTS FOR CONDUCTORS AND EARTH ELECTRODES |
| 10/30212801 DC : 0 | BS 6180 - BARRIERS IN AND ABOUT BUILDINGS - CODE OF PRACTICE |
| PREN 50341-1 : DRAFT 2012 | OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS |
| BS 7903:1997 | Guide to selection and use of gully tops and manhole covers for installation within the highway |
| 06/30150265 DC : 0 | EN 1474-1 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS |
| CEI EN 50397-2 : 2011 | COVERED CONDUCTORS FOR OVERHEAD LINES AND THE RELATED ACCESSORIES FOR RATED VOLTAGES ABOVE 1 KV AC AND NOT EXCEEDING 36 KV AC - PART 2: ACCESSORIES FOR COVERED CONDUCTORS - TESTS AND ACCEPTANCE CRITERIA |
| NF EN 61897 : 2001 | OVERHEAD LINES - REQUIREMENTS AND TESTS FOR STOCKBRIDGE TYPE AEOLIAN VIBRATION DAMPERS |
| I.S. EN 124:1994 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - DESIGN REQUIREMENTS, TYPE TESTING, MARKING, QUALITY CONTROL |
| 12/30238456 DC : 0 | BS EN 13438 - PAINTS AND VARNISHES - POWDER ORGANIC COATINGS FOR GALVANIZED OR SHERARDIZED STEEL PRODUCTS FOR CONSTRUCTION PURPOSES |
| BS EN ISO 16904:2016 | Petroleum and natural gas industries. Design and testing of LNG marine transfer arms for conventional onshore terminals |
| 15/30328805 DC : 0 | BS EN 16927 - MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS |
| BS EN 62561-2:2012 | Lightning Protection System Components (LPSC) Requirements for conductors and earth electrodes |
| PREN 15773 : DRAFT 2016 | INDUSTRIAL APPLICATION OF POWDER ORGANIC COATINGS TO HOT DIP GALVANIZED OR SHERARDIZED STEEL ARTICLES [DUPLEX SYSTEMS] - SPECIFICATIONS, RECOMMENDATIONS AND GUIDELINES |
| 07/30140820 DC : 0 | BS ISO 25457 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLARE DETAILS FOR GENERAL REFINERY AND PETROCHEMICAL SERVICE |
| BS ISO 13628-7 : 2005 AMD 16887 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 7: COMPLETION/WORKOVER RISER SYSTEMS |
| 05/30129619 DC : DRAFT FEB 2005 | IEC 61537 ED.2 - CABLE TRAY SYSTEMS AND CABLE LADDER SYSTEMS FOR CABLE MANAGEMENT |
| DIN 83206:2011-12 | Stairs and guard rails for engine rooms and boiler rooms in seagoing ships - Stairs |
| DIN EN 15644:2009-03 | TRADITIONALLY DESIGNED PREFABRICATED STAIRS MADE OF SOLID WOOD - SPECIFICATIONS AND REQUIREMENTS |
| BS EN ISO 25457:2008 | Petroleum, petrochemical and natural gas industries. Flare details for general refinery and petrochemical service |
| 04/30111935 DC : DRAFT APR 2004 | ISO 13706 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - AIRCOOLED HEAT EXCHANGERS |
| DIN EN 14545:2009-02 | TIMBER STRUCTURES - CONNECTORS - REQUIREMENTS |
| 01/122232 DC : DRAFT JUNE 2001 | BS ISO 20340 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PERFORMANCE REQUIREMENTS FOR PROTECTIVE PAINT SYSTEMS FOR OFFSHORE AND RELATED STRUCTURES |
| 16/30340708 DC : 0 | BS EN 10348-2 - STEEL FOR THE REINFORCEMENT OF CONCRETE - GALVANIZED REINFORCING STEEL - PART 2: GALVANIZED REINFORCING STEEL PRODUCTS |
| 12/30265747 DC : 0 | BS EN 845-2 - SPECIFICATION FOR ANCILLARY COMPONENTS FOR MASONRY - PART 2: LINTELS |
| BS EN 15644:2008 | Traditionally designed prefabricated stairs made of solid wood. Specifications and requirements |
| 11/30246055 DC : 0 | BS EN ISO 13705 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FIRED HEATERS FOR GENERAL REFINERY SERVICE |
| EN 16582-1:2015 | Domestic swimming pools - Part 1: General requirements including safety and test methods |
| DIN EN ISO 15589-2:2014-07 | Petroleum, petrochemical and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines (ISO 15589-2:2012) |
| 16/30337296 DC : 0 | BS EN ISO 12944-4 - PAINTS AND VARNISHES - CORROSION PROTECTION OF STEEL STRUCTURES BY PROTECTIVE PAINT SYSTEMS - PART 4: TYPES OF SURFACE AND SURFACE PREPARATION |
| 10/30233309 DC : 0 | BS EN 10255 - NON-ALLOY STEEL TUBES SUITABLE FOR WELDING AND THREADING - TECHNICAL DELIVERY CONDITIONS |
| 98/103738 DC : DRAFT APR 1998 | PREN 12899-2 - ROAD EQUIPMENT - FIXED, VERTICAL ROAD SIGNS - PART 2: TRANSILLUMINATED TRAFFIC BOLLARDS |
| I.S. EN ISO 14713-1:2017 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 1: GENERAL PRINCIPLES OF DESIGN AND CORROSION RESISTANCE (ISO 14713-1:2017) |
| ISO 12944-9:2018 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 9: Protective paint systems and laboratory performance test methods for offshore and related structures |
| 14/30297213 DC : 0 | BS EN 1473 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN OF ONSHORE INSTALLATIONS |
| 98/716843 DC : DRAFT OCT 1998 | ISO 799:1986/PDAM 1 - SHIPS AND MARINE TECHNOLOGY - PILOT LADDERS |
| S.R. CEN/TS 16811-3:2015 | WINTER MAINTENANCE EQUIPMENT - DE-ICING AGENTS - PART 3: OTHER SOLID AND LIQUID DE-ICING AGENTS - REQUIREMENTS AND TEST METHODS |
| I.S. EN ISO 16904:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND TESTING OF LNG MARINE TRANSFER ARMS FOR CONVENTIONAL ONSHORE TERMINALS (ISO 16904:2016) |
| API 616 REDLINE : 2011 | GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES |
| PREN 10219-2 : DRAFT 2016 | COLD FORMED WELDED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| DIN EN 16582-1:2015-11 | Domestic swimming pools - Part 1: General requirements including safety and test methods |
| API 616 : 2011 | GAS TURBINES FOR THE PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES |
| I.S. EN ISO 14713-2:2009 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
| I.S. EN 50397-2:2009 | COVERED CONDUCTORS FOR OVERHEAD LINES AND THE RELATED ACCESSORIES FOR RATED VOLTAGES ABOVE 1 KV AC AND NOT EXCEEDING 36 KV AC - PART 2: ACCESSORIES FOR COVERED CONDUCTORS - TESTS AND ACCEPTANCE CRITERIA |
| I.S. EN ISO 1891-2:2014 | FASTENERS - TERMINOLOGY - PART 2: VOCABULARY AND DEFINITIONS FOR COATINGS (ISO 1891-2:2014) |
| API 537 REDLINE : 2008 | FLARE DETAILS FOR GENERAL REFINERY AND PETROCHEMICAL SERVICE |
| KTA 3205.2 : 2015 COR 2016 | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT |
| BS EN 10025-6 : 2004 | HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 6: TECHNICAL DELIVERY CONDITIONS FOR FLAT PRODUCTS OF HIGH YIELD STRENGTH STRUCTURAL STEELS IN THE QUENCHED AND TEMPERED CONDITION |
| I.S. EN ISO 25457:2009 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - FLARE DETAILS FOR GENERAL REFINERY AND PETROCHEMICAL SERVICE |
| I.S. EN 12496:2013 | GALVANIC ANODES FOR CATHODIC PROTECTION IN SEAWATER AND SALINE MUD |
| I.S. EN 124-3:2015 | GULLY TOPS AND MANHOLE TOPS FOR VEHICULAR AND PEDESTRIAN AREAS - PART 3: GULLY TOPS AND MANHOLE TOPS MADE OF STEEL OR ALUMINIUM ALLOYS |
| EN 15773:2018 | Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines |
| I.S. EN IEC 62688:2018 | CONCENTRATOR PHOTOVOLTAIC (CPV) MODULES AND ASSEMBLIES - SAFETY QUALIFICATION |
| ISO 12944-6:2018 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 6: Laboratory performance test methods |
| 16/30332614 DC : 0 | BS EN 10219-2 - COLD FORMED WELDED STRUCTURAL STEEL HOLLOW SECTIONS - PART 2: TECHNICAL DELIVERY CONDITIONS |
| CEI EN 50216-10 : 2010 | POWER TRANSFORMER AND REACTOR FITTINGS - PART 10: OIL-TO-AIR HEAT EXCHANGERS |
| DIN EN 16927:2015-10 (Draft) | MINI POOLS - SPECIFIC REQUIREMENTS INCLUDING SAFETY AND TEST METHODS FOR MINI POOLS |
| IEC 60168:1994+AMD1:1997+AMD2:2000 CSV | Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V |
| DIN EN ISO 10684:2011-09 | Fasteners - Hot dip galvanized coatings (ISO 10684:2004 + Cor. 1:2008) |
| DIN EN 10255:2015-05 (Draft) | Non-Alloy steel tubes suitable for welding, threading and other joining methods - Requirements and test methods; German and English version prEN 10255:2015 |
| BS EN ISO 15749-1:2004 | Ships and marine technology. Drainage systems on ships and marine structures Sanitary drainage-system design |
| BS EN ISO 13706:2011 | Petroleum, petrochemical and natural gas industries. Aircooled heat exchangers |
| ISO 14713:1999 | Protection against corrosion of iron and steel in structures — Zinc and aluminium coatings — Guidelines |
| ISO 15589-2:2012 | Petroleum, petrochemical and natural gas industries — Cathodic protection of pipeline transportation systems — Part 2: Offshore pipelines |
| BS EN ISO 14713:1999 | Protection against corrosion of iron and steel in structures. Zinc and aluminium coatings. Guidelines |
| 01/715268 DC : DRAFT NOV 2001 | BS ISO 13628-7 - PETROLEUM AND NATURAL GAS INDUSTRIES - DESIGN AND OPERATION OF SUBSEA PRODUCTION SYSTEMS - PART 7: COMPLETION/WORKOVER RISER SYSTEMS |
| BS EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming Technical delivery conditions for normalized or normalized rolled steels |
| BS EN 62271-202:2014 | High-voltage switchgear and controlgear High-voltage/low-voltage prefabricated substation |
| DIN EN ISO 14713-2:2010-05 | ZINC COATINGS - GUIDELINES AND RECOMMENDATIONS FOR THE PROTECTION AGAINST CORROSION OF IRON AND STEEL IN STRUCTURES - PART 2: HOT DIP GALVANIZING |
| EN 10305-1:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubes |
| BS 493(1995) : 1995 | SPECIFICATION FOR AIRBRICKS AND GRATINGS FOR WALL VENTILATION |
| EN 12329 : 2000 | CORROSION PROTECTION OF METALS - ELECTRODEPOSITED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENT ON IRON OR STEEL |
| EN 13101:2002 | Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity |
| EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
| DIN EN 516:2006-04 | Prefabricated accessories for roofing - Installations for roof access - Walkways, treads and steps |
| DIN EN ISO 2081:2009-05 | METALLIC AND OTHER INORGANIC COATINGS - ELECTROPLATED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENTS ON IRON OR STEEL |
| DIN EN 10255:2007-07 | Non-alloy steel tubes suitable for welding and threading - Technical delivery conditions (includes Amendment A1:2007) |
| EN 50164-2:2008 | Lightning Protection Components (LPC) - Part 2: Requirements for conductors and earth electrodes |
| EN 61325:1995 | Insulators for overhead lines with a nominal voltage above 1 kV - Ceramic or glass insulator units for d.c. systems - Definitions, test methods and acceptance criteria |
| DIN EN ISO 15749-1:2004-09 | Ships and marine technology - Drainage systems on ships and marine structures - Part 1: Sanitary drainage-system design (ISO 15749-1:2004) |
| EN 61537:2007 | Cable management - Cable tray systems and cable ladder systems |
| DIN CEN/TS 16811-3;DIN SPEC 30757:2016-08 | WINTER SERVICE EQUIPMENT AND PRODUCTS - DE-ICING AGENTS - PART 3: OTHER SOLID AND LIQUID DE-ICING AGENTS - REQUIREMENTS AND TEST METHODS |
| DIN EN 13411-1:2009-02 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 1: THIMBLES FOR STEEL WIRE ROPE SLINGS |
| DIN EN 517:2006-05 | Prefabricated accessories for roofing - Roof safety hooks |
| EN 13283:2002 | Zinc and zinc alloys - Secondary zinc |
| EN 10255:2004+A1:2007 | Non-Alloy steel tubes suitable for welding and threading - Technical delivery conditions |
| EN 50216-10:2009 | Power transformer and reactor fittings - Part 10: Oil-to-air heat exchangers |
| EN 50397-2:2009 | Covered conductors for overhead lines and the related accessories for rated voltages above 1 kV AC and not exceeding 36 kV AC - Part 2: Accessories for covered conductors - Tests and acceptance criteria |
| UNE-EN 14490:2013 | Execution of special geotechnical works - Soil nailing |
| API STD 2RD:2013(R2020) | Dynamic Risers for Floating Production Systems, Second Edition |
| I.S. EN ISO 10684:2004 | FASTENERS - HOT DIP GALVANIZED COATINGS |
| I.S. EN 1123-1:1999 | PIPES AND FITTINGS OF LONGITUDINALLY WELDED HOT-DIP GALVANIZED STEEL PIPES WITH SPIGOT AND SOCKET FOR WASTE WATER SYSTEMS - REQUIREMENTS, TESTING, QUALITY CONTROL |
| I.S. EN 14475:2006 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - REINFORCED FILL |
| I.S. EN 1433:2002 | DRAINAGE CHANNELS FOR VEHICULAR AND PEDESTRIAN AREAS - CLASSIFICATION, DESIGN AND TESTING REQUIREMENTS, MARKING AND EVALUATION OF CONFORMITY |
| UNE-EN 62561-2:2012 | Lightning Protection System Components (LPSC) - Part 2: Requirements for conductors and earth electrodes |
| UNE-EN 12899-2:2010 | Fixed, vertical road traffic signs - Part 2: Transilluminated traffic bollards (TTB) |
| UNE-EN 16927:2017 | Mini-pools - Specific requirements including safety and test methods for mini-pools |
| UNE-EN ISO 1891-2:2015 | Fasteners - Terminology - Part 2: Vocabulary and definitions for coatings (ISO 1891-2:2014) |
| UNE-EN 10223-4:2013 | Steel wire and wire products for fencing and netting - Part 4: Steel wire welded mesh fencing |
| UNE-EN 50216-10:2010 | Power transformer and reactor fittings - Part 10: Oil-to-air heat exchangers |
| UNE-EN 10305-2:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 2: Welded cold drawn tubes |
| UNE-EN 10149-2:2014 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| UNE-EN 14475:2011 | Execution of special geotechnical works - Reinforced fill |
| UNE-EN ISO 14713-2:2011 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
| UNE-EN 12496:2013 | Galvanic anodes for cathodic protection in seawater and saline mud |
| UNE-EN 124-4:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 4: Gully tops and manhole tops made of steel reinforced concrete |
| UNE-EN 13071-2:2008 | Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 2: Additional requirements for underground or partly underground systems |
| UNE-EN 12574-2:2017 | Stationary waste containers - Part 2: Performance requirements and test methods |
| UNE-EN 1765:2017 | Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies |
| UNE 135314:2017 | Vertical signs. Galvanized steel profiles used as post of the signs, side posters and directional signs. Moving supporting elements. Screw products. Characteristics and test methods. |
| UNE-EN 10223-7:2013 | Steel wire and wire products for fencing and netting - Part 7: Steel wire welded panels for fencing |
| UNE-EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
| UNE-EN 10305-3:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes |
| UNE-EN ISO 2081:2010 | Metallic and other inorganic coatings - Electroplated coatings of zinc with supplementary treatments on iron or steel (ISO 2081:2008) |
| UNE-EN 10305-5:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 5: Welded cold sized square and rectangular tubes |
| UNE-EN ISO 16904:2016 | Petroleum and natural gas industries - Design and testing of LNG marine transfer arms for conventional onshore terminals (ISO 16904:2016) |
| UNE-EN 1317-5:2008 | Road restraint systems - Part 5: Product requirements and evaluation of conformity for vehicle restraint systems |
| UNE-EN 1090-2:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| UNE-EN 14592:2009 | Timber structures - Dowel-type fasteners - Requirements |
| UNE-EN 10149-3:2014 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
| UNE-EN 10223-2:2013 | Steel wire and wire products for fencing and netting - Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes |
| UNE-EN 124-3:2015 | Gully tops and manhole tops for vehicular and pedestrian areas - Part 3: Gully tops and manhole tops made of steel or aluminium alloys |
| UNE 135366:2011 | Vertical signs. Vertical retroreflectors. Characteristics and test methods. |
| UNE-EN 1995-1-1:2016 | Eurocode 5: Design of timber structures - Part 1-1: General - Common rules and rules for buildings. |
| UNE-EN 840-5:2013 | Mobile waste and recycling containers - Part 5: Performance requirements and test methods |
| UNE-EN 16582-1:2015 | Domestic swimming pools - Part 1: General requirements including safety and test methods |
| NACE SP 06 07 : 2007 | PETROLEUM AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE |
| UNE-EN 10305-1:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubes |
| UNE-EN ISO 15589-2:2014 | Petroleum, petrochemical and natural gas industries - Cathodic protection of pipeline transportation systems - Part 2: Offshore pipelines (ISO 15589-2:2012) |
| UNE-EN 10223-8:2014 | Steel wire and wire products for fencing and netting - Part 8: Welded mesh gabion products |
| UNE-EN 62271-202:2015 | High-voltage switchgear and controlgear - Part 202: High-voltage/low-voltage prefabricated substation |
| UNE-EN 15773:2010 | Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines |
| I.S. EN IEC 61730-1:2018 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| NBR ISO 15589-2 : 2015 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - CATHODIC PROTECTION OF PIPELINE TRANSPORTATION SYSTEMS - PART 2: OFFSHORE PIPELINES |
| ISO 9223:2012 | Corrosion of metals and alloys — Corrosivity of atmospheres — Classification, determination and estimation |
| ISO 2063:2005 | Thermal spraying — Metallic and other inorganic coatings — Zinc, aluminium and their alloys |
| ISO 2859-3:2005 | Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
| ISO 3549:1995 | Zinc dust pigments for paints — Specifications and test methods |
| ISO 12944-5:2007 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 5: Protective paint systems |
| ISO 2808:2007 | Paints and varnishes — Determination of film thickness |
| ISO 752:2004 | Zinc ingots |
| ISO 1463:2003 | Metallic and oxide coatings — Measurement of coating thickness — Microscopical method |
| ISO 3882:2003 | Metallic and other inorganic coatings — Review of methods of measurement of thickness |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| EN 746-4:2000 | Industrial thermoprocessing equipment - Part 4: Particular safety requirements for hot dip galvanising thermoprocessing equipment |
| EN 13438:2013 | Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
| EN 13283:2002 | Zinc and zinc alloys - Secondary zinc |
| EN 1179:2003 | Zinc an zinc alloys - Primary zinc |
| ISO 16276-2:2007 | Corrosion protection of steel structures by protective paint systems — Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating — Part 2: Cross-cut testing and X-cut testing |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method |
| ISO 1460:1992 | Metallic coatings — Hot dip galvanized coatings on ferrous materials — Gravimetric determination of the mass per unit area |
| ISO 2064:1996 | Metallic and other inorganic coatings — Definitions and conventions concerning the measurement of thickness |
| ISO 6988:1985 | Metallic and other non organic coatings — Sulfur dioxide test with general condensation of moisture |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.