ISO 8605:2001
Withdrawn
Withdrawn
View Superseded by
Textile-glass-reinforced plastics — Sheet moulding compound (SMC) — Basis for a specification
Available format(s)
Hardcopy , PDF
Language(s)
English, French
Published date
05-31-2001
Withdrawn date
04-09-2025
Superseded by
US$96.00
Excluding Tax where applicable
| Committee |
ISO/TC 61/SC 13
|
| DocumentType |
Standard
|
| Pages |
9
|
| PublisherName |
International Organization for Standardization
|
| Status |
Withdrawn
|
| SupersededBy | |
| Supersedes | |
| UnderRevision |
| Standards | Relationship |
| NF ISO 8605 : 2002 | Identical |
| BS ISO 8605:2001 | Identical |
| NFT 57 510 : 1984 | Identical |
| NEN ISO 8605 : 2001 | Identical |
| DIN EN 14598-3:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| DIN EN 13421:2006-05 | Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites |
| BS EN ISO 12114:1997 | Fibre-reinforced plastics. Thermosetting moulding compounds and prepregs. Determination of cure characteristics |
| BS EN 13280:2001 | Specification for glass fibre reinforced cisterns of one-piece and sectional construction, for the storage, above ground, of cold water |
| BS EN 13421:2006 | Plastics. Thermoset moulding compounds. Composites and reinforcement fibres. Preparation of specimens for determining the anisotropy of the properties of compression moulding composites |
| ISO 12114:1997 | Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics |
| BS EN 14598-3:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements |
| EN 13280:2001 | Specification for glass fibre reinforced cisterns of one piece and sectional construction, for the storage, above ground, of cold water |
| EN ISO 12114:1997 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of cure characteristics (ISO 12114:1997) |
| EN ISO 12115:1997 | Fibre-reinforced plastics - Thermosetting moulding compounds and prepregs - Determination of flowability, maturation and shelf life (ISO 12115:1997) |
| EN 14598-3:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| BS EN ISO 12115:1997 | Fibre-reinforced plastics. Thermosetting moulding compounds and prepregs. Determination of flowability, maturation and shelf life |
| EN 13421:2006 | Plastics - Thermoset moulding compounds - Composites and reinforcement fibres - Preparation of specimens for determining the anisotropy of the properties of compression moulding composites |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 11667:1997 | Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods |
| ISO 527-4:1997 | Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 1172:1996 | Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods |
| ISO 3672-1:2000 | Plastics — Unsaturated-polyester resins (UP-R) — Part 1: Designation system |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 9782:1993 | Plastics — Reinforced moulding compounds and prepregs — Determination of apparent volatile-matter content |
| IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 180:2000 | Plastics — Determination of Izod impact strength |
| ISO 2577:2007 | Plastics — Thermosetting moulding materials — Determination of shrinkage |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method |
| ISO 1886:1990 | Reinforcement fibres — Sampling plans applicable to received batches |
| ISO 1183-3:1999 | Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas pyknometer method |
| ISO 291:2008 | Plastics — Standard atmospheres for conditioning and testing |
| ISO 3673-1:1996 | Plastics — Epoxy resins — Part 1: Designation |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 14125:1998 | Fibre-reinforced plastic composites — Determination of flexural properties |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 14130:1997 | Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength by short-beam method |
| ISO 14126:1999 | Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane direction |
| ISO 12114:1997 | Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of cure characteristics |
| ISO 10352:2010 | Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of mass per unit area |
Summarise
US$96.00
Excluding Tax where applicable
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.