NF EN 60335-2-75 : 2005 AMD 12 2013
Current
HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES - SAFETY - PART 2-75: PARTICULAR REQUIREMENTS FOR COMMERCIAL DISPENSING APPLIANCES AND VENDING MACHINES
01-12-2013
AVANT-PROPOS
INTRODUCTION
1 Domaine d'application
2 Références normatives
3 Définitions
4 Exigences générales
5 Conditions générales d'essais
6 Classification
7 Marquage et instructions
8 Protection contre l'accès aux parties actives
9 Démarrage des appareils à moteur
10 Puissance et courant
11 Echauffements
12 Vacant
13 Courant de fuite et rigidité diélectrique à la
température de régime
14 Surtensions transitoires
15 Résistance à l'humidité
16 Courant de fuite et rigidité diélectrique
17 Protection contre la surcharge des transformateurs
et des circuits associés
18 Endurance
19 Fonctionnement anormal
20 Stabilité et dangers mécaniques
21 Résistance mécanique
22 Construction
23 Conducteurs internes
24 Composants
25 Raccordement au réseau et câbles souples extérieurs
26 Bornes pour conducteurs externes
27 Dispositions en vue de la mise à la terre
28 Vis et connexions
29 Distances d'isolement, lignes de fuite et isolation solide
30 Résistance à la chaleur et au feu
31 Protection contre la rouille
32 Rayonnement, toxicité et dangers analogues
Annexes
Annexe AA (normative) Essai de vieillissement des parties
en élastomère
Annexe ZC (normative) Références normatives à d'autres
publications internationales avec les
publications européennes correspondantes
Annexe ZAA (normative) Machines à café espresso électriques à
usage commercial pouvant être chauffées
également au gaz
Annexe ZBB (normative) Mesure du bruit acoustique
Bibliographie
Figure 101 - Appareil de projection pour l'essai
d'éclaboussement
Deals with the safety of commercial electric dispensing appliances and vending machines for preparation or delivery of food, drinks and consumer products, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. It also applies to commercial electric espresso-coffee machines that can also be heated by gas
| DevelopmentNote |
Indice de classement: C73-875PR. Supersedes NFC 73 875 (05/2005) PR NF EN 60335-2-75 March 2012. (03/2012) Supersedes NF EN 60335 2-63. (08/2012)
|
| DocumentType |
Standard
|
| PublisherName |
Association Francaise de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| BS EN 60335-2-75 : 2004 | Identical |
| DIN EN 60335-2-75 : 2010 | Identical |
| EN 60335-2-75:2004/A12:2010 | Identical |
| I.S. EN 60335-2-75:2004 | Identical |
| UNE-EN 60335-2-75:2005 | Identical |
| NF EN ISO 228-1 : 2003 | PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION |
| NFD 30 520 : 1994 | |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for an essentially free field over a reflecting plane |
| NF EN 437 : 2003 + A1 2009 | TEST GASES - TEST PRESSURES - APPLIANCE CATEGORIES |
| NF EN ISO 3744 : 2012 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE |
| ISO/TR 11688-1:1995 | Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning |
| NF EN ISO 3743-1 : 2012 | ACOUSTICS - DETERMINATION OF SOUND POWER LEVELS AND SOUND ENERGY LEVELS OF NOISE SOURCES USING SOUND PRESSURE - ENGINEERING METHODS FOR SMALL MOVABLE SOURCES IN REVERBERANT FIELDS - PART 1: COMPARISON METHOD FOR A HARD-WALLED TEST ROOM |
| IEC 60335-2-34:2012+AMD1:2015+AMD2:2016 CSV | Household and similar electrical appliances - Safety - Part 2-34:Particular requirements for motor-compressors |
| NF EN ISO 11201 : 2010 | ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS IN AN ESSENTIALLY FREE FIELD OVER A REFLECTING PLANE WITH NEGLIGIBLE ENVIRONMENTAL CORRECTIONS |
| NF EN ISO 4871 : 2009 | ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT |
| CR 1472:1997 | General guidance for the marking of gas appliances |
| CR 1749 : 2001 | EUROPEAN SCHEME FOR THE CLASSIFICATION OF GAS APPLIANCES ACCORDING TO THE METHOD OF EVACUATION OF THE PRODUCTS OF COMBUSTION (TYPES) |
| FD CR 1472 : 1999 FD | GENERAL GUIDANCE FOR THE MARKING OF GAS APPLIANCES |
| ISO 11201:2010 | Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
| NF EN ISO 11688-1 : 2009 | ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING |
| ISO 3743-1:2010 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for small movable sources in reverberant fields — Part 1: Comparison method for a hard-walled test room |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |