S.R. CWA 16060:2009
Withdrawn
ENVIRONMENTAL TECHNOLOGY VERIFICATION - AIR EMISSION ABATEMENT TECHNOLOGIES
Hardcopy , PDF
English
01-01-2009
05-13-2021
Foreword
Introduction
1 Scope
2 Terms and definitions
3 Prerequisite and general requirements
4 Procedure
5 Test process and report
6 Verification
7 Data dissemination
8 Liability
Annex A - Monitoring standards for verification
Annex B - Measurement uncertainty
Bibliography
Defines a guideline for the verification of air emission abatement technologies and it specifies a reporting structure for a verified vendor claim for the performance of a specific air emission abatement technology.
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| CEN/TS 15675:2007 | Air quality - Measurement of stationary source emissions - Application of EN ISO/IEC 17025:2005 to periodic measurements |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| ISO 23210:2009 | Stationary source emissions — Determination of PM10/PM2,5 mass concentration in flue gas — Measurement at low concentrations by use of impactors |
| ISO 11338-1:2003 | Stationary source emissions — Determination of gas and particle-phase polycyclic aromatic hydrocarbons — Part 1: Sampling |
| EN 14791:2017 | Stationary source emissions - Determination of mass concentration of sulphur oxides - Standard reference method |
| ISO 14956:2002 | Air quality — Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty |
| ISO 15713:2006 | Stationary source emissions — Sampling and determination of gaseous fluoride content |
| EN 13649:2001 | Stationary source emissions - Determination of the mass concentration of individual gaseous organic compounds - Activated carbon and solvent desorption method |
| EN 13526:2001 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon in flue gases from solvent using processes - Continuous flame ionisation detector method |
| EN 15259:2007 | Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report |
| ISO/IEC Guide 99:2007 | International vocabulary of metrology — Basic and general concepts and associated terms (VIM) |
| EN 13284-1:2017 | Stationary source emissions - Determination of low range mass concentration of dust - Part 1: Manual gravimetric method |
| EN 14181:2014 | Stationary source emissions - Quality assurance of automated measuring systems |
| EN 15058:2017 | Stationary source emissions - Determination of the mass concentration of carbon monoxide - Standard reference method: non-dispersive infrared spectrometry |
| EN 12619:2013 | Stationary source emissions - Determination of the mass concentration of total gaseous organic carbon - Continuous flame ionisation detector method |
| ISO 11338-2:2003 | Stationary source emissions — Determination of gas and particle-phase polycyclic aromatic hydrocarbons — Part 2: Sample preparation, clean-up and determination |
| EN ISO 14956:2002 | Air quality - Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty (ISO 14956:2002) |
| EN ISO 23210:2009 | Stationary source emissions - Determination of PM10/PM2,5 mass concentration in flue gas - Measurement at low concentrations by use of impactors (ISO 23210:2009) |
| EN 14385:2004 | Stationary source emissions - Determination of the total emission of As, Cd, Cr, Co, Cu, Mn, Ni, Pb, Sb, TI and V |
| EN 14792:2017 | Stationary source emissions - Determination of mass concentration of nitrogen oxides - Standard reference method: chemiluminescence |
| PREN 1911 : DRAFT 2008 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF GASEOUS CHLORIDES EXPRESSED AS HCL - STANDARD REFERENCE METHOD |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.