NFPA 262 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
METHOD OF TEST FOR FLAME TRAVEL AND SMOKE OF WIRES AND CABLES FOR USE IN AIR-HANDLING SPACES
Hardcopy
12-18-2018
English
01-01-2015
Chapter 1 - Administration
Chapter 2 - Referenced Publications
Chapter 3 - Definitions
Chapter 4 - Test Apparatus
Chapter 5 - Test Specimens
Chapter 6 - Maintenance and Calibration of Test
Equipment
Chapter 7 - Test Specimen Preparation
Chapter 8 - Test Procedure
Chapter 9 - Post-Test Cleanup and Inspection
Chapter 10 - Calculations
Chapter 11 - Report
Chapter 12 - Precision and Bias
Annex A - Explanatory Material
Annex B - Smoke and Heat Release
Measurements
Annex C - Smoke Measurement System and
Chamber-Brick Configuration: Detail Drawings
Annex D - Standard Reference Cable Test
Annex E - Informational References
Index
Describes the methodology to measure flame travel distance and optical density of smoke for insulated, jacketed, or both, electrical wires and cables and optical fiber cables that are to be installed in plenums and other spaces used to transport environmental air without being enclosed in raceways.
DevelopmentNote |
Supersedes UL 910 (04/2004)
|
DocumentType |
Standard
|
Pages |
38
|
PublisherName |
National Fire Protection Association
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
CSA C22.2 No. 211.0 :2003 | GENERAL REQUIREMENTS AND METHODS OF TESTING FOR NONMETALLIC CONDUIT |
CSA C22.2 No. 131 : 2014 | TYPE TECK 90 CABLE |
NFPA 502 : 2017 | ROAD TUNNELS, BRIDGES, AND OTHER LIMITED ACCESS HIGHWAYS |
NFPA 76 : 2016 | FIRE PROTECTION OF TELECOMMUNICATIONS FACILITIES |
NFPA 557 : 2016 | DETERMINATION OF FIRE LOAD FOR USE IN STRUCTURAL FIRE PROTECTION DESIGN |
EN 60695-9-2:2014 | Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods |
03/318326 DC : DRAFT NOV 2003 | |
UNE-EN 60695-8-2:2017 | Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods |
EN 60695-8-2:2017 | Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods |
CSA C22.2 No. 211.0 : 2003 : INC : UPD 3 : 2011 : R200800 | GENERAL REQUIREMENTS AND METHODS OF TESTING FOR NONMETALLIC CONDUIT |
MIL-STD-1678-3 Revision C:2016 | FIBER OPTIC CABLING SYSTEMS REQUIREMENTS AND MEASUREMENTS - PART 3: PHYSICAL, MECHANICAL, ENVIRONMENTAL AND MATERIAL MEASUREMENTS (PART 3 OF 6 PARTS) |
CSA C22.2 No. 0.3 :2009 | TEST METHODS FOR ELECTRICAL WIRES AND CABLES |
CSA C22.2 No. 130 : 2016 | REQUIREMENTS FOR ELECTRICAL RESISTANCE TRACE HEATING AND HEATING DEVICE SETS |
NFPA 301 : 2018 | SAFETY TO LIFE FROM FIRE ON MERCHANT VESSELS |
NFPA 90A : 2018 | INSTALLATION OF AIR-CONDITIONING AND VENTILATING SYSTEMS |
NFPA 130 : 2017 | FIXED GUIDEWAY TRANSIT AND PASSENGER RAIL SYSTEMS |
I.S. EN 60695-9-2:2014 | FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS |
CEI EN 60695-6-2 : 2013 | FIRE HAZARD TESTING - PART 6-2: SMOKE OBSCURATION - SUMMARY AND RELEVANCE OF TEST METHODS |
PD IEC/TR 62222:2012 | Fire performance of communication cables installed in buildings |
CSA M421 : 2011 | USE OF ELECTRICITY IN MINES |
IEEE 532-2007 REDLINE | IEEE Guide for Selecting and Testing Jackets for Power, Instrumentation, and Control Cables |
I.S. EN 60695-8-2:2017 | FIRE HAZARD TESTING - PART 8-2: HEAT RELEASE - SUMMARY AND RELEVANCE OF TEST METHODS |
CSA C22.2 No. 0.3 : 2009 : R2014 | TEST METHODS FOR ELECTRICAL WIRES AND CABLES |
I.S. EN 60695-6-2:2011 | FIRE HAZARD TESTING - PART 6-2: SMOKE OBSCURATION - SUMMARY AND RELEVANCE OF TEST METHODS (IEC 60695-6-2:2011) |
CSA C22.2 No. 262 : 2004 : R2013 | OPTICAL FIBER CABLE AND COMMUNICATION CABLE RACEWAY SYSTEMS |
UNE-EN 60695-9-2:2014 | Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods |
IEC TS 60695-9-2:2005 | Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods |
IEC 60695-6-2:2011 | Fire hazard testing - Part 6-2: Smoke obscuration - Summary and relevance of test methods |
IEC 60695-9-2:2014 | Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods |
ISO/TR 10093:2017 | Plastics Fire tests Standard ignition sources |
UL 444:5ED 2017-01 | Communications Cables |
CSA M421 : 2011 : R2016 | USE OF ELECTRICITY IN MINES |
ICC IMC Code and Commentary : 2015 | IMC® Code and Commentary |
ASTM D 6113 : 2016 : REDLINE | Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test-Response Characteristics of Insulating Materials Contained in Electrical or Optical Fiber Cables |
CSA C22.2 No. 210 : 2015 | APPLIANCE WIRING MATERIAL PRODUCTS |
CSA C22.2 No. 262 : 2004 : R2009 | OPTICAL FIBER CABLE AND COMMUNICATION CABLE RACEWAY SYSTEMS |
CSA C22.2 No. 210.2 : 2001 | APPLIANCE WIRING MATERIAL PRODUCTS |
IEC TS 60695-6-2:2005 | Fire hazard testing - Part 6-2: Smoke obscuration - Summary and relevance of test methods |
DD IEC TS 60695-9-2 : DRAFT 2005 | FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS |
DD IEC TS 60695-6-2 : DRAFT 2005 | FIRE HAZARD TESTING - PART 6-2: SMOKE OBSCURATION - SUMMARY AND RELEVANCE OF TEST METHODS |
BS IEC TS 60695-9.2 : 2001 | FIRE HAZARD TESTING - PART 9-2 - SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS |
BS EN 60695-9-2:2014 | Fire hazard testing Surface spread of flame. Summary and relevance of test methods |
BS EN 60695-8-2:2017 | Fire hazard testing Heat release. Summary and relevance of test methods |
09/30193524 DC : 0 | BS EN 62222 - FIRE PERFORMANCE OF COMMUNICATION CABLES INSTALLED IN BUILDINGS - METHODS OF FIRE RETARDANCY |
IEC TR 62222:2012 | Fire performance of communication cables installed in buildings |
CAN/CSA-C22.2 NO. 262-04 (R2018) | Optical Fiber Cable and Communication Cable Raceway Systems |
C22.2 NO. 232-17 | Optical fiber cables |
C22.2 NO. 214-17 | Communications cables (Bi-national standard, with UL 444) |
C22.2 NO. 211.0-03 (R2017) | General Requirements and Methods of Testing for Nonmetallic Conduit |
UNE-EN 60695-6-2:2012 | Fire hazard testing - Part 6-2: Smoke obscuration - Summary and relevance of test methods |
IEC TR 60695-8-2:2008 | Fire hazard testing - Part 8-2: Heat release - Summary and relevance of test methods |
CSA C22.2 No. 211.0 : 2003 : INC : UPD 3 : 2011 : R2013 | GENERAL REQUIREMENTS AND METHODS OF TESTING FOR NONMETALLIC CONDUIT |
IEEE 1682-2011 | IEEE Standard for Qualifying Fiber Optic Cables, Connections, and Optical Fiber Splices for Use in Safety Systems in Nuclear Power Generating Stations |
13/30277762 DC : 0 | BS EN 60695-8-2 IEC 60695-8-2 ED 1.0 - FIRE HAZARD TESTING - PART 8-2: HEAT RELEASE - SUMMARY AND RELEVANCE OF TEST METHODS |
BS EN 60695-6-2:2011 | Fire hazard testing Smoke obscuration. Summary and relevance of test methods |
PD IEC/TR 60695-8-2:2008 | Fire hazard testing Heat release. Summary and relevance of test methods |
04/30111706 DC : DRAFT MAR 2004 | IEC 60695-9-2 ED.2 - FIRE HAZARD TESTING - PART 9-2: SURFACE SPREAD OF FLAME - SUMMARY AND RELEVANCE OF TEST METHODS |
ICC 2012 INTERNATIONAL MECH. CODE : 2012 | INTERNATIONAL MECHANICAL CODE |
EN 60695-6-2 : 2011 | FIRE HAZARD TESTING - PART 6-2: SMOKE OBSCURATION - SUMMARY AND RELEVANCE OF TEST METHODS (IEC 60695-6-2:2011) |
NFPA 90A : 2018 | INSTALLATION OF AIR-CONDITIONING AND VENTILATING SYSTEMS |
ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
UL 2196:2ED 2017-08 | Fire Test for Circuit Integrity of Fire-Resistive Power, Instrumentation, Control and Data Cables |
NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
ASTM D 4100 : 1982 : R1989 : EDT 1 | Test Method for Gravimetric Determination of Smoke Particulates from Combustion of Plastic Materials (Withdrawn 1997) |
ASTM D 746 : 2014 : REDLINE | Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.