• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ANSI/CSA NGV 5.1-2016 (R2020)

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

Residential fueling appliances
Available format(s)

Hardcopy , PDF

Withdrawn date

10-02-2023

Language(s)

English

Published date

01-01-2016

Preface This is the second edition of ANSI/CSA NGV 5.1, Residential fueling appliances. CSA Group acknowledges that the development of this Standard was made possible, in part, by the financial support of the Advanced Research Projects Agency-Energy (ARPA-E), U.S. Department of Energy, under Award Number DE-AR000375. Scope 1.1 General This Standard details mechanical, physical, and electrical requirements for a newly manufactured appliance that dispenses natural gas for vehicles directly into the vehicle natural gas fuel storage system, referred to as a residential fueling appliance (RFA). 1.2 Application These requirements apply to appliances: a) for natural gas only (see Clause 1.1) b) for outdoor or indoor installation in nonliving spaces (e.g., garage) c) for ambient temperature not below minus 40ºC (minus 40 ºF) d) for nominal voltage not exceeding 240 Volts AC e) for fill pressure not exceeding specified vehicle service pressure f) for maximum inlet flow rate not exceeding 10 SCFM (17 SCMH) g) intended for connection to residential utility gas piping system in accordance with requirements of the applicable Code h) intended to meet the installation fire safety requirements in accordance with the requirements of the applicable Code i) single and dual fueling hose gas compressor packages 1.3 Pressure references All references to \"kpa\" and \"psi\" throughout this Standard are to be considered gauge pressures, unless otherwise specified. 1.4 Resolution of conflicts In the case of conflict between this Standard and Federal, National, Provincial, State, or local requirements, the authority having jurisdiction requirements take precedence. 1.5 Units of measure This Standard contains SI (Metric) units corresponding to the inch/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, the first stated unit, or both are to be provided. Note: IEEE/ASTM SI 10 or ISO 80000-1 is used as a guide in making metric conversion from inch/pound quantities. 1.6 Terminology In this Standard, \"shall\" is used to express a requirement, i.e., a provision that the user shall satisfy in order to comply with the standard; \"should\" is used to express a recommendation or that which is advised but not required; and \"may\" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Preface This is the second edition of ANSI/CSA NGV 5.1, Residential fueling appliances. CSA Group acknowledges that the development of this Standard was made possible, in part, by the financial support of the Advanced Research Projects Agency-Energy (ARPA-E), U.S. Department of Energy, under Award Number DE-AR000375. Scope 1.1 General This Standard details mechanical, physical, and electrical requirements for a newly manufactured appliance that dispenses natural gas for vehicles directly into the vehicle natural gas fuel storage system, referred to as a residential fueling appliance (RFA). 1.2 Application These requirements apply to appliances: a) for natural gas only (see Clause 1.1) b) for outdoor or indoor installation in nonliving spaces (e.g., garage) c) for ambient temperature not below minus 40ºC (minus 40 ºF) d) for nominal voltage not exceeding 240 Volts AC e) for fill pressure not exceeding specified vehicle service pressure f) for maximum inlet flow rate not exceeding 10 SCFM (17 SCMH) g) intended for connection to residential utility gas piping system in accordance with requirements of the applicable Code h) intended to meet the installation fire safety requirements in accordance with the requirements of the applicable Code i) single and dual fueling hose gas compressor packages 1.3 Pressure references All references to \"kpa\" and \"psi\" throughout this Standard are to be considered gauge pressures, unless otherwise specified. 1.4 Resolution of conflicts In the case of conflict between this Standard and Federal, National, Provincial, State, or local requirements, the authority having jurisdiction requirements take precedence. 1.5 Units of measure This Standard contains SI (Metric) units corresponding to the inch/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, the first stated unit, or both are to be provided. Note: IEEE/ASTM SI 10 or ISO 80000-1 is used as a guide in making metric conversion from inch/pound quantities. 1.6 Terminology In this Standard, \"shall\" is used to express a requirement, i.e., a provision that the user shall satisfy in order to comply with the standard; \"should\" is used to express a recommendation or that which is advised but not required; and \"may\" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

DocumentType
Standard
ISBN
978-1-4883-0374-6
Pages
79
PublisherName
Canadian Standards Association
Status
Withdrawn
Supersedes

IEC 61025:2006 Fault tree analysis (FTA)
CSA NGV1 : 2017 COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES
SAE J 200 : 2015 CLASSIFICATION SYSTEM FOR RUBBER MATERIALS
ASME B18.2.1 : 2012 SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES)
ANSI Z21.21 : 2015 AUTOMATIC VALVES FOR GAS APPLIANCES
UL 514A:11ED 2013-02 Metallic Outlet Boxes
ANSI NGV1 : 2017 COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES
ANSI/CSA NGV 4.2-2014 (R2019)/CSA 12.52-2014 (R2018) Hoses for natural gas dispensing systems
C22.1-15 Canadian Electrical Code, Part I (23rd Edition), Safety Standard for Electrical Installations
CSA B51 : 2014 BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE
IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
CSA C22.2 No. 77 : 2014 MOTORS WITH INHERENT OVERHEATING PROTECTION
CSA 6.5 : 2015 AUTOMATIC VALVES FOR GAS APPLIANCES
SAE J 102 : 1992 SQUARE HEAD SETSCREWS
ASME B18.6.4 : 1998 THREAD FORMING AND THREAD CUTTING TAPPING SCREWS AND METALLIC DRIVE SCREWS, INCH SERIES
ASTM D 1149 : 2016-02 TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
CSA C22.2 No. 0.4 : 2004(R2013) BONDING OF ELECTRICAL EQUIPMENT
CSA C22.2 No. 0.5 : 2016 THREADED CONDUIT ENTRIES
NFPA 79 : 2015 ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY
CSA C22.2 No. 24 : 2015 TEMPERATURE-INDICATING AND -REGULATING EQUIPMENT
ANSI NGV3.1 : 2014 FUEL SYSTEM COMPONENTS FOR COMPRESSED NATURAL GAS POWERED VEHICLES
UL 795:8ED 2016-12 Commercial-Industrial Gas Heating Equipment
CSA C22.2 No. 139 : 2013 ELECTRICALLY OPERATED VALVES
ASME B40.100 : 2013 Pressure Gauges and Gauge Attachments (B40.100 - 2013)
CSA 12.3 : 2014 FUEL SYSTEM COMPONENTS FOR COMPRESSED NATURAL GAS POWERED VEHICLES
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
SAE J 1065 : 2016 NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING
CSA 12.56 : 1999 MANUALLY OPERATED VALVES FOR NATURAL GAS DISPENSING SYSTEMS
ASTM D 1822 : 2013 Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
SAE J 1739 : 2009 POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA)
MIL-STD-882 Revision E:2012 System Safety
NFPA 52 : 2016 VEHICULAR NATURAL GAS FUEL SYSTEMS CODE
ASME B36.10M : 2015 WELDED AND SEAMLESS WROUGHT STEEL PIPE
ASTM D 865 : 2011 Standard Test Method for Rubber<char: emdash>Deterioration by Heating in Air (Test Tube Enclosure)
NFPA 70 : 2017 NATIONAL ELECTRICAL CODE
SAE J 526 : 2016 WELDED LOW-CARBON STEEL TUBING SUITABLE FOR BENDING, FLARING, BEADING, FORMING AND BRAZING
ISO 80000-1:2009 Quantities and units — Part 1: General
SAE J 525 : 2016 WELDED AND COLD DRAWN LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING
ASTM D 648 : 2016 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
CSA C22.2 No. 100 : 2014 MOTORS AND GENERATORS
SAE J 1183 : 2017 RECOMMENDED GUIDELINES FOR FATIGUE TESTING OF ELASTOMERIC MATERIALS AND COMPONENTS
SAE J 524 : 2016 SEAMLESS LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING
UL 429:7ED 2013-11 Electrically Operated Valves
ASTM D 790 : 2010 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
CFR 49(PTS400-599) : 0 TRANSPORTATION
ASME B18.2.2 : 2015 NUTS FOR GENERAL APPLICATIONS: MACHINE SCREW NUTS, HEX, SQUARE, HEX FLANGE, AND COUPLING NUTS (INCH SERIES)
ASTM D 5420 : 2016 Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
SAE J 105 : 1992 HEX BOLTS
NFPA 54 : 2018 NATIONAL FUEL GAS CODE
C22.2 NO. 236-15 Heating and cooling equipment (Bi-national standard with UL 1995)
ASME PV CODE SET : 2017 BOILER AND PRESSURE VESSEL CODE - COMPLETE SET
ANSI Z223.1 : 2018 NATIONAL FUEL GAS CODE
ASTM D 471 : 2016-02 TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
UL 515:2ED 2015-07 Standard for Electrical Resistance Trace Heating for Commercial Applications
SAE J 479 : 1992 SLOTTED HEADLESS SETSCREWS
UL 60079-0:6ED 2013-07 Explosive Atmospheres - Part 0: Equipment - General Requirements
SAE J 478 : A SLOTTED AND RECESSED HEAD SCREWS
ASME B18.6.3 : 2013 MACHINE SCREWS, TAPPING SCREWS, AND METALLIC DRIVE SCREWS (INCH SERIES)
ASTM D 638 : 2010 Standard Test Method for Tensile Properties of Plastics
NFPA 497 : 2017 CLASSIFICATION OF FLAMMABLE LIQUIDS, GASES, OR VAPORS AND OF HAZARDOUS (CLASSIFIED) LOCATIONS FOR ELECTRICAL INSTALLATIONS IN CHEMICAL PROCESS AREAS

View more information
$868.46
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more