Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 5550 : 2014 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Specific Gravity of Soil Solids by Gas Pycnometer
Available format(s)

PDF

Superseded date

16-03-2023

Language(s)

English

Published date

14-01-2015

CONTAINED IN VOL. 04.08, 2017 Specifies the determination of the specific gravity of soil solids by means of a gas pycnometer. Particle size is limited by the dimensions of the specimen container of the particular pycnometer being used.

1.1This test method covers the determination of the specific gravity of soil solids by means of a gas pycnometer. Particle size is limited by the dimensions of the specimen container of the particular pycnometer being used.

1.2Test Method D854 may be used instead of or in conjunction with this test method for performing specific gravity tests on soils. Note that Test Method D854 does not require the specialized test apparatus needed by this test method. However, Test Method D854 may not be used if the specimen contains matter that can readily dissolve in water, whereas this test method does not have that limitation.

1.3All measured and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.3.1For purposes of comparing a measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits.

1.3.2The procedures used to specify how data are collected/recorded and calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

1.4Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units, which are provided for information only and are not considered standard.

1.4.1The converted inch-pound units use the gravitational system of units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The converted slug unit is not given, unless dynamic (F = ma) calculations are involved.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 18
DocumentType
Redline
Pages
5
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 854 : 2014 : REDLINE Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023)
ASTM E 2277 : 2014 Standard Guide for Design and Construction of Coal Ash Structural Fills
ASTM D 4018 : 2017 : REDLINE Standard Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber Tows
BS EN ISO 19901-8:2015 Petroleum and natural gas industries. Specific requirements for offshore structures Marine soil investigations
TP 117 : 2015 METHOD OF TEST FOR DETERMINATION OF THE VOIDS OF DRY COMPACTED FILLER
ISO 19901-8:2014 Petroleum and natural gas industries — Specific requirements for offshore structures — Part 8: Marine soil investigations
CSA ISO 19901-8 : 2015 PETROLEUM AND NATURAL GAS INDUSTRIES - SPECIFIC REQUIREMENTS FOR OFFSHORE STRUCTURES - PART 8: MARINE SOIL INVESTIGATIONS
CSA ISO 19901-8:15 (R2020) Petroleum and natural gas industries — Specific requirements for offshore structures — Part 8: Marine soil investigations (Adopted ISO 19901-8:2014, first edition, 2014-12-01)
I.S. EN ISO 19901-8:2015 PETROLEUM AND NATURAL GAS INDUSTRIES - SPECIFIC REQUIREMENTS FOR OFFSHORE STRUCTURES - PART 8: MARINE SOIL INVESTIGATIONS (ISO 19901-8:2014)
EN ISO 19901-8:2015 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 8: Marine soil investigations (ISO 19901-8:2014)
13/30257183 DC : 0 BS EN ISO 19901-8 - PETROLEUM AND NATURAL GAS INDUSTRIES - SPECIFIC REQUIREMENTS FOR OFFSHORE STRUCTURES - PART 8: MARINE SOIL INVESTIGATIONS

ASTM D 3740 : 2012-06 PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION
ASTM D 854 : 2014 : REDLINE Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023)
ASTM D 4753 : 2015 : REDLINE Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing
ASTM D 6026 : 2013 : REDLINE Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 653 : 2014 : REDLINE Standard Terminology Relating to Soil, Rock, and Contained Fluids

View more information
$122.77
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more