Customer Support: 131 242

  • There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 653 : 2014 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Terminology Relating to Soil, Rock, and Contained Fluids

Available format(s)

PDF

Superseded date

03-09-2020

Language(s)

English

Published date

01-08-2014

CONTAINED IN VOL. 04.08, 2017 Describes terms related to soil, rock and contained fluids found in the terminology sections of standards under the jurisdiction of ASTM Committee D18.

1.1These definitions apply to many terms found in the Terminology section of standards of ASTM Committee D18.

1.2This terminology standard defines terms related to soil, rock, and contained fluids found in the various sections of standards under the jurisdiction of ASTM Committee D18.

1.3Definitions of terms relating to frozen soils are contained in Terminology D7099.

Committee
D 18
DevelopmentNote
Supersedes ASTM D 1707. (02/2002)
DocumentType
Redline
Pages
64
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM F 480 : 2014 : REDLINE Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80
ASTM D 4016 : 2014 : REDLINE Standard Test Method for Viscosity and Gel Time of Chemical Grouts by Rotational Viscometer (Laboratory Method)
ASTM D 6706 : 2001 : R2013 Standard Test Method for Measuring Geosynthetic Pullout Resistance in Soil
ASTM D 5311/D5311M : 2013 : REDLINE Standard Test Method for Load Controlled Cyclic Triaxial Strength of Soil
ASTM D 7764 : 2012 Standard Practice for Pre-Installation Acceptance Testing of Vibrating Wire Piezometers
ASTM F 2747 : 2010 Standard Guide for Construction of Sand-based Rootzones for Golf Putting Greens and Tees (Withdrawn 2019)
ASTM D 5716 : 1995 : R2006 Standard Test Method for Measuring the Rate of Well Discharge by Circular Orifice Weir (Withdrawn 2015)
ASTM D 7276 : 2016 : REDLINE Standard Guide for Analysis and Interpretation of Test Data for Articulating Concrete Block (ACB) Revetment Systems in Open Channel Flow
ASTM D 4700 : 2015 : REDLINE Standard Guide for Soil Sampling from the Vadose Zone
ASTM D 5777 : 2000 : R2011 : EDT 1 Standard Guide for Using the Seismic Refraction Method for Subsurface Investigation
ASTM D 6452 : 1999 : R2005 Standard Guide for Purging Methods for Wells Used for Groundwater Quality Investigations
ASTM D 7272 : 2006 : R2018 Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Premanufactured Taped Methods
ASTM D 5858 : 1996 : R2003 Standard Guide for Calculating <ital>In Situ</ital> Equivalent Elastic Moduli of Pavement Materials Using Layered Elastic Theory
ASTM D 8081 : 2017 Standard Guide for Theory and Principles for Obtaining Reliable and Accurate Bulk Solids Flow Data Using a Direct Shear Cell
ASTM D 5923 : 1996 : R2004 Standard Guide for Selection of Kriging Methods in Geostatistical Site Investigations
ASTM D 7759/D7759M : 2014 : REDLINE Standard Guide for Nuclear Surface Moisture and Density Gauge Calibration
ASTM D 5995 : 1998 : R2010 Standard Guide for Environmental Site Characterization in Cold Regions
ASTM D 5410 : 1993 : R1998 Standard Guide for Set of Data Elements to Describe a Ground-Water Site; Part Three-Usage Descriptors
ASTM D 5493 : 2006 : R2016 Standard Test Method for Permittivity of Geotextiles Under Load
ASTM D 6913 : 2004 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 5299 : 1999 : R2012 : EDT 1 Standard Guide for Decommissioning of Groundwater Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities
ASTM D 5995 : 1998 : R2004 Standard Guide for Environmental Site Characterization in Cold Regions
ASTM D 7128 : 2005 : R2010 Standard Guide for Using the Seismic-Reflection Method for Shallow Subsurface Investigation
ASTM D 5858 : 1996 : R2008 Standard Guide for Calculating <span class="italic">In Situ</span> Equivalent Elastic Moduli of Pavement Materials Using Layered Elastic Theory
ASTM D 3551 : 2017 Standard Practice for Laboratory Preparation of Soil-Lime Mixtures Using Mechanical Mixer
ASTM F 1668 : 2016 : REDLINE Standard Guide for Construction Procedures for Buried Plastic Pipe
ASTM D 7243 : 2011 : REDLINE Standard Guide for Measuring the Saturated Hydraulic Conductivity of Paper Industry Sludges
ASTM D 6598 : 2011 : REDLINE Standard Guide for Installing and Operating Settlement Platforms for Monitoring Vertical Deformations
ASTM D 4753 : 2015 : REDLINE Standard Guide for Evaluating, Selecting, and Specifying Balances and Standard Masses for Use in Soil, Rock, and Construction Materials Testing
ASTM D 1143/D1143M : 2007 : R2013 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load
ASTM D 6635 : 2015 : REDLINE Standard Test Method for Performing the Flat Plate Dilatometer
ASTM D 6067/D6067M : 2017 : REDLINE Standard Practice for Using the Electronic Piezocone Penetrometer Tests for Environmental Site Characterization and Estimation of Hydraulic Conductivity
ASTM D 4793 : 2009 Standard Test Method for Sequential Batch Extraction of Waste with Water
ASTM D 6913 : 2004 : EDT 1 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 5880 : 1995 : R2000 Standard Guide for Subsurface Flow and Transport Modeling
ASTM D 5608 : 2016 : REDLINE Standard Practices for Decontamination of Sampling and Non Sample Contacting Equipment Used at Low Level Radioactive Waste Sites
ASTM D 5447 : 2017 : REDLINE Standard Guide for Application of a Numerical Groundwater Flow Model to a Site-Specific Problem
ASTM D 4083 : 1989 : R2001 : EDT 1 Standard Practice for Description of Frozen Soils (Visual-Manual Procedure)
ASTM D 5922 : 1996 : R2004 Standard Guide for Analysis of Spatial Variation in Geostatistical Site Investigations
ASTM D 5877 : 1995 : R2005 Standard Guide for Displaying Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements<char: emdash>Diagrams Based on Data Analytical Calculations (Withdrawn 2014)
ASTM D 4406 : 2004 Standard Test Method for Creep of Cylindrical Rock Core Specimens in Triaxial Compression (Withdrawn 2005)
ASTM D 5080 : 2017 : REDLINE Standard Test Method for Rapid Determination of Percent Compaction
ASTM D 5490 : 1993 : R2008 Standard Guide for Comparing Groundwater Flow Model Simulations to Site-Specific Information
ASTM E 2838 : 2011 Standard Test Method for Determination of Thiodiglycol on Wipes by Solvent Extraction Followed by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS)
ASTM D 6724 : 2004 Standard Guide for Installation of Direct Push Ground Water Monitoring Wells
ASTM D 5092 : 2004 : EDT 1 Standard Practice for Design and Installation of Ground Water Monitoring Wells
ASTM D 5611 : 1994 : R2002 Standard Guide for Conducting a Sensitivity Analysis for a Ground-Water Flow Model Application
ASTM D 6236 : 2011 : REDLINE Standard Guide for Coring and Logging Cement - or Lime-Stabilized Soil
ASTM E 2531 : 2006 Standard Guide for Development of Conceptual Site Models and Remediation Strategies for Light Nonaqueous-Phase Liquids Released to the Subsurface
ASTM E 2838 : 2011 : R2016 Standard Test Method for Determination of Thiodiglycol on Wipes by Solvent Extraction Followed by Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS)
ASTM D 6088 : 2006 Standard Practice for Installation of Geocomposite Pavement Drains
ASTM D 6088 : 2006 : R2016 Standard Practice for Installation of Geocomposite Pavement Drains
ASTM D 5995 : 1998 Standard Guide for Environmental Site Characterization in Cold Regions
ASTM D 6517 : 2000 : R2005 Standard Guide for Field Preservation of Groundwater Samples
ASTM E 2531 : 2006 : R2014 Standard Guide for Development of Conceptual Site Models and Remediation Strategies for Light Nonaqueous-Phase Liquids Released to the Subsurface
ASTM D 698 : 2013-05 TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3]))
ASTM D 5785 : 1995 : R2000 Standard Test Method for (Analytical Procedure) for Determining Transmissivity of Confined Nonleaky Aquifers by Underdamped Well Response to Instantaneous Change in Head (Slug Test)
ASTM D 5521 : 2005 Standard Guide for Development of Groundwater Monitoring Wells in Granular Aquifers
ASTM D 7181 : 2011 Method for Consolidated Drained Triaxial Compression Test for Soils
ASTM D 4253 : 2016 : REDLINE Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 6393 : 2014 : REDLINE Standard Test Method for Bulk Solids Characterization by Carr Indices
ASTM D 6276 : 1999 : REV A Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization
ASTM D 6564 : 2000 : R2012 : EDT 1 Standard Guide for Field Filtration of Groundwater Samples
ASTM D 5092 : 2004 Standard Practice for Design and Installation of Ground Water Monitoring Wells in Aquifers
ASTM D 7046 : 2011 : REDLINE Standard Guide for Use of the Metal Detection Method for Subsurface Exploration
ASTM D 6170 : 2017 : REDLINE Standard Guide for Selecting a Groundwater Modeling Code
ASTM D 1557 : 2012 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>))
ASTM D 3550/D3550M : 2017 Standard Practice for Thick Wall, Ring-Lined, Split Barrel, Drive Sampling of Soils
ASTM D 4748 : 2010 : R2015 Standard Test Method for Determining the Thickness of Bound Pavement Layers Using Short-Pulse Radar
ASTM D 2435/D2435M : 2011 : REDLINE Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading
ASTM D 854 : 2014 : REDLINE Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023)
ASTM D 8107 : 2018 : REDLINE Standard Practice for Determining Sediment Pond Skimmer Flow Rate
ASTM D 7263 : 2009 : R2018 : EDT 1 Standard Test Methods for Laboratory Determination of Density (Unit Weight) of Soil Specimens
ASTM D 3385 : 2009-03 TEST METHOD FOR INFILTRATION RATE OF SOILS IN FIELD USING DOUBLE-RING INFILTROMETER
ASTM D 5978 : 1996 : R2011 : EDT 1 Standard Guide for Maintenance and Rehabilitation of Groundwater Monitoring Wells
ASTM D 7352:2007 Standard Practice for Direct Push Technology for Volatile Contaminant Logging with the Membrane Interface Probe (MIP)
ASTM D 2944 : 2014 : REDLINE Standard Practice of Sampling Processed Peat Materials
ASTM D 5738 : 1995 : R2006 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements<char: emdash>Diagrams for Single Analyses (Withdrawn 2015)
ASTM D 5731 : 2016 : REDLINE Standard Test Method for Determination of the Point Load Strength Index of Rock and Application to Rock Strength Classifications
ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 2974 : 2014 : REDLINE Standard Test Methods for Moisture, Ash, and Organic Matter of Peat and Other Organic Soils
ASTM D 6527 : 2000 Standard Test Method for Determining Unsaturated and Saturated Hydraulic Conductivity in Porous Media by Steady-State Centrifugation
ASTM D 6171 : 1997 : R2010 Standard Guide for Documenting a Groundwater Modeling Code (Withdrawn 2019)
ASTM D 7891 : 2015 Standard Test Method for Shear Testing of Powders Using the Freeman Technology FT4 Powder Rheometer Shear Cell
ASTM D 6036 : 1996 : R2008 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements<char: emdash>Use of Maps
ASTM D 5233 : 1992 : R2009 Standard Test Method for Single Batch Extraction Method for Wastes
ASTM D 7698 : 2011 : REV A : REDLINE Standard Test Method for In-Place Estimation of Density and Water Content of Soil and Aggregate by Correlation with Complex Impedance Method
ASTM D 6564 : 2000 Standard Guide for Field Filtration of Ground-Water Samples
ASTM D 4531 : 2015 : REDLINE Standard Test Methods for Bulk and Dry Density of Peat and Peat Products
ASTM D 5409 : 1993 : R1998 Standard Guide for Set of Data Elements to Describe a Ground-Water Site; Part Two-Physical Descriptors
ASTM D 6171 : 1997 : EDT 1 Standard Guide for Documenting a Ground-Water Modeling Code
ASTM D 4491 : 1999 : REV A : R2004 : EDT 1 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 5434 : 2012 Standard Guide for Field Logging of Subsurface Explorations of Soil and Rock (Withdrawn 2021)
ASTM D 5784 : 1995 : R2000 Standard Guide for Use of Hollow-Stem Augers for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 5472 : 1993 : R2005 Standard Test Method for Determining Specific Capacity and Estimating Transmissivity at the Control Well (Withdrawn 2014)
ASTM D 5141 : 2011 Standard Test Method for Determining Filtering Efficiency and Flow Rate of the Filtration Component of a Sediment Retention Device
ASTM E 1676 : 2012 : REDLINE Standard Guide for Conducting Laboratory Soil Toxicity or Bioaccumulation Tests with the Lumbricid Earthworm <i>Eisenia Fetida</i> and the Enchytraeid Potworm <i>Enchytraeus albidus</i>
ASTM D 5490 : 1993 : R2002 Standard Guide for Comparing Ground-Water Flow Model Simulations to Site-Specific Information
ASTM D 6285 : 1999 : R2005 Standard Guide for Locating Abandoned Wells
ASTM D 4612 : 2016 : REDLINE Standard Test Method for Calculating Thermal Diffusivity of Rock and Soil
ASTM D 1140 : 2017 : REDLINE Standard Test Methods for Determining the Amount of Material Finer than 75-μm (No. 200) Sieve in Soils by Washing
ASTM D 5285 : 2003 Standard Test Method for 24-Hour Batch-Type Measurement of Volatile Organic Sorption by Soils and Sediments (Withdrawn 2008)
ASTM F 1759 : 1997 : R2004 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
ASTM D 6430 : 2018 : REDLINE Standard Guide for Using the Gravity Method for Subsurface Site Characterization
ASTM D 4718/D4718M : 2015 : REDLINE Standard Practice for Correction of Unit Weight and Water Content for Soils Containing Oversize Particles
ASTM D 7277 : 2016 : REDLINE Standard Test Method for Performance Testing of Articulating Concrete Block (ACB) Revetment Systems for Hydraulic Stability in Open Channel Flow
ASTM D 425 : 2017 : REDLINE Standard Test Method for Centrifuge Moisture Equivalent of Soils
ASTM D 5408 : 1993 : R2004 Standard Guide for Set of Data Elements to Describe a Ground-Water Site; Part One-Additional Identification Descriptors
ASTM D 6103 : 2004 Standard Test Method for Flow Consistency of Controlled Low Strength Material (CLSM) (Withdrawn 2013)
ASTM E 2277 : 2014 Standard Guide for Design and Construction of Coal Ash Structural Fills
ASTM D 4394 : 2017 : REDLINE Standard Test Method for Determining In Situ Modulus of Deformation of Rock Mass Using Rigid Plate Loading Method
ASTM D 5141 : 2011 : R2018 Standard Test Method for Determining Filtering Efficiency and Flow Rate of the Filtration Component of a Sediment Retention Device
ASTM D 4044 : 1996 : R2002 Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifiers
ASTM D 5922 : 1996 : R2010 Standard Guide for Analysis of Spatial Variation in Geostatistical Site Investigations
ASTM E 2060 : 2006 Standard Guide for Use of Coal Combustion Products for Solidification/Stabilization of Inorganic Wastes
ASTM D 7762 : 2018 : REDLINE Standard Practice for Design of Stabilization of Soil and Soil-Like Materials with Self-Cementing Fly Ash
ASTM D 6640 : 2001 : R2015 Standard Practice for Collection and Handling of Soils Obtained in Core Barrel Samplers for Environmental Investigations
ASTM D 4914/D4914M : 2016 : REDLINE Standard Test Methods for Density of Soil and Rock in Place by the Sand Replacement Method in a Test Pit
ASTM D 5270 : 1996 : R2014 Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers
ASTM D 4945 : 2017 : REDLINE Standard Test Method for High-Strain Dynamic Testing of Deep Foundations
ASTM D 5030 : 2004 Standard Test Method for Density of Soil and Rock in Place by the Water Replacement Method in a Test Pit
ASTM D 6027 : 1996 : EDT 1 Standard Test Method for Calibrating Linear Displacement Transducers for Geotechnical Purposes
AWWA M45 : 3 FIBERGLASS PIPE DESIGN
ASTM D 6758 : 2018 Standard Test Method for Measuring Stiffness and Apparent Modulus of Soil and Soil-Aggregate In-Place by Electro-Mechanical Method
ASTM D 4320 : 2004 Standard Practice for Laboratory Preparation of Chemically Grouted Soil Specimens for Obtaining Design Strength Parameters
ASTM D 6276 : 1999 : REV A : R2006 Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization
ASTM D 5473 : 1993 : R2000 Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer
ASTM D 4373 : 2014 : REDLINE Standard Test Method for Rapid Determination of Carbonate Content of Soils
ASTM D 4623 : 2016 : REDLINE Standard Test Method for Determination of In Situ Stress in Rock Mass by Overcoring Method—Three Component Borehole Deformation Gauge
ASTM D 5233 : 1992 : R2017 Standard Test Method for Single Batch Extraction Method for Wastes
ASTM D 6234 : 2013 : REDLINE Standard Test Method for Shake Extraction of Mining Waste by the Synthetic Precipitation Leaching Procedure
ASTM D 7830/D7830M : 2014 : REDLINE Standard Test Method for In-Place Density (Unit Weight) and Water Content of Soil Using an Electromagnetic Soil Density Gauge
MIL-PRF-53090 Revision B:2016 BLADE, MINE CLEARING
ASTM D 4254 : 2016 : REDLINE Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 6028 : 2017 : REDLINE Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer Taking into Consideration Storage of Water in Leaky Confining Beds by Modified Hantush Method
ASTM D 5539 : 2014 : REDLINE SPECIFICATION FOR SEED STARTER MIX
ASTM D 5783 : 2018 : REDLINE Standard Guide for Use of Direct Rotary Drilling with Water-Based Drilling Fluid for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 5269 : 2015 : REDLINE Standard Test Method for Determining Transmissivity of Nonleaky Confined Aquifers by the Theis Recovery Method
AASHTO R 13 : 2012 PRACTICE FOR CONDUCTING GEOTECHNICAL SUBSURFACE INVESTIGATIONS
ASTM D 5718 : 2013 : REDLINE Standard Guide for Documenting a Groundwater Flow Model Application
ASTM D 5850 : 2018 : REDLINE Standard Test Method for (Analytical Procedure) Determining Transmissivity, Storage Coefficient, and Anisotropy Ratio from a Network of Partially Penetrating Wells
ASTM D 6146 : 1997 : R2007 Standard Guide for Monitoring Aqueous Nutrients in Watersheds
ASTM D 6025 : 1996 : R2008 Standard Guide for Developing and Evaluating Groundwater Modeling Codes (Withdrawn 2017)
ASTM D 5980 : 2016 : REDLINE Standard Guide for Selection and Documentation of Existing Wells for Use in Environmental Site Characterization and Monitoring
ASTM D 7272 : 2006 Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Pre-manufactured Taped Methods
ASTM D 5410 : 1993 : R2007 Standard Guide for Set of Data Elements to Describe a Groundwater Site;<br> Part Three<char: emdash>Usage Descriptors (Withdrawn 2016)
ASTM D 8106 : 2017 Standard Test Methods for Determining the Oil Sorption Capacity of Organophilic Clay
ASTM D 4223 : 1999 : R2006 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
ASTM D 4104 : 2017 : REDLINE Standard Test Method (Analytical Procedure) for Determining Transmissivity of Nonleaky Confined Aquifers by Overdamped Well Response to Instantaneous Change in Head (Slug Tests)
ASTM D 6026 : 2013 : REDLINE Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 6106 : 1997 : R2004 Standard Guide for Establishing the Nomenclature of Ground-Water Aquifers
ASTM D 5270 : 1996 Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers
ASTM D 5782 : 2018 : REDLINE Standard Guide for Use of Direct Air-Rotary Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 6243/D6243M : 2016 : REDLINE Standard Test Method for Determining the Internal and Interface Shear Strength of Geosynthetic Clay Liner by the Direct Shear Method
ASTM D 4644 : 2016 : REDLINE Standard Test Method for Slake Durability of Shales and Other Similar Weak Rocks
ASTM D 3740 : 2012-06 PRACTICE FOR MINIMUM REQUIREMENTS FOR AGENCIES ENGAGED IN TESTING AND/OR INSPECTION OF SOIL AND ROCK AS USED IN ENGINEERING DESIGN AND CONSTRUCTION
ASTM D 5911/D5911M : 1996 : R2010 : EDT 1 Standard Practice for Minimum Set of Data Elements to Identify a Soil Sampling Site (Withdrawn 2019)
ASTM D 1632 : 2017 Standard Practice for Making and Curing Soil-Cement Compression and Flexure Test Specimens in the Laboratory
ASTM D 6025 : 1996 : R2002 Standard Guide for Developing and Evaluating Ground-Water Modeling Codes
ASTM D 6312 : 2017 : REDLINE Standard Guide for Developing Appropriate Statistical Approaches for Groundwater Detection Monitoring Programs at Waste Disposal Facilities
ASTM F 2107 : 2008 : R2015 Standard Guide for Construction and Maintenance of Skinned Areas on Baseball and Softball Fields
ASTM D 7069 : 2004 Standard Guide for Field Quality Assurance in a Ground-water Sampling Event
ASTM F 2107 : 2008 Standard Guide for Construction and Maintenance of Skinned Areas on Baseball and Softball Fields
ASTM D 5233 : 1992 : R1999 Standard Test Method for Single Batch Extraction Method for Wastes
ASTM D 5472 : 1993 : R1999 : EDT 1 Standard Test Method for Determining Specific Capacity and Estimating Transmissivity at the Control Well
ASTM D 5924 : 1996 : R2010 Standard Guide for Selection of Simulation Approaches in Geostatistical Site Investigations
ASTM D 5979 : 1996 : EDT 1 Standard Guide for Conceptualization and Characterization of Ground-Water Systems
ASTM D 560/D560M : 2016 : REDLINE Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures
ASTM D 5092 : 2004 : R2010 : EDT 1 Standard Practice for Design and Installation of Groundwater Monitoring Wells
ASTM D 5473/D5473M : 2015 Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer
ASTM D 5982 : 2015 : REDLINE Standard Test Method for Determining Cement Content of Fresh Soil-Cement (Heat of Neutralization Method)
ASTM D 5255 : 2015 : REDLINE Standard Practice for Certification of Personnel Engaged in the Testing of Soil and Rock
ASTM D 6187 : 1997 : R2010 Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence (Withdrawn 2019)
ASTM D 6106 : 1997 : EDT 1 Standard Guide for Establishing the Nomenclature of Ground-Water Aquifers
ASTM E 2866 : 2012 Standard Test Method for Determination of Diisopropyl Methylphosphonate, Ethyl Methylphosphonic Acid, Isopropyl Methylphosphonic Acid, Methylphosphonic Acid and Pinacolyl Methylphosphonic Acid in Soil by Pressurized Fluid Extraction and Analyzed by Liquid
ASTM D 6452 : 1999 Standard Guide for Purging Methods for Wells Used for Ground-Water Quality Investigations
ASTM D 5858 : 1996 : EDT 1 Standard Guide for Calculating In Situ Equivalent Elastic Moduli of Pavement Materials Using Layered Elastic Theory
ASTM D 7401 : 2008 Standard Test Methods for Laboratory Determination of Rock Anchor Capacities by Pull and Drop Tests (Withdrawn 2017)
ASTM D 7499/D7499M : 2009 : R2014 Standard Test Method for Measuring Geosynthetic-Soil Resilient Interface Shear Stiffness
ASTM D 5784 : 1995 : R2006 Standard Guide for Use of Hollow-Stem Augers for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 559/D559M : 2015 Standard Test Methods for Wetting and Drying Compacted Soil-Cement Mixtures
ASTM D 5195 : 2014 : REDLINE Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods
ASTM D 5874 : 2016 : REDLINE Standard Test Methods for Determination of the Impact Value (IV) of a Soil
ASTM D 5924 : 1996 : EDT 1 Standard Guide for Selection of Simulation Approaches in Geostatistical Site Investigations
ASTM D 5737 : 1995 : R2000 Standard Guide for Methods for Measuring Well Discharge
ASTM D 5334 : 2014 : REDLINE Standard Test Method for Determination of Thermal Conductivity of Soil and Soft Rock by Thermal Needle Probe Procedure
ASTM D 8064 : 2016 Standard Test Method for Elemental Analysis of Soil and Solid Waste by Monochromatic Energy Dispersive X-ray Fluorescence Spectrometry Using Multiple Monochromatic Excitation Beams (Withdrawn 2024)
ASTM D 5101 : 2012 TEST METHOD FOR MEASURING THE FILTRATION COMPATIBILITY OF SOIL-GEOTEXTILE SYSTEMS
ASTM D 1143/D1143M : 2007 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load
ASTM D 5716 : 1995 : R2000 Standard Test Method for Measuring the Rate of Well Discharge by Circular Orifice Weir
ASTM D 6146 : 1997 : R2002 Standard Guide for Monitoring Aqueous Nutrients in Watersheds
ASCE/CI 36 15 : 2015 STANDARD DESIGN AND CONSTRUCTION GUIDELINES FOR MICROTUNNELING
ASTM D 4427 : 2018 : REDLINE Standard Classification of Peat Samples by Laboratory Testing
ASTM D 5101 : 2012 : R2017 Standard Test Method for Measuring the Filtration Compatibility of Soil-Geotextile Systems
AASHTO TP 100 : 2012 : R2015 METHOD OF TEST FOR DEEP FOUNDATION ELEMENTS UNDER BIDIRECTIONAL STATIC AXIAL COMPRESSIVE LOAD
ASTM D 8037/D8037M : 2016 Standard Practice for Direct Push Hydraulic Logging for Profiling Variations of Permeability in Soils
ASTM D 4223 : 1999 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
ASTM D 5313 : 2004 Standard Test Method for Evaluation of Durability of Rock for Erosion Control Under Wetting and Drying Conditions
ASTM D 7299 : 2012 : REDLINE Standard Practice for Verifying Performance of a Vertical Inclinometer Probe
ASTM D 4971 : 2016 : REDLINE Standard Test Method for Determining In Situ Modulus of Deformation of Rock Using Diametrically Loaded 76-mm (3-in.) Borehole Jack
ASTM D 4648/D4648M : 2016 : REDLINE Standard Test Methods for Laboratory Miniature Vane Shear Test for Saturated<brk/>Fine-Grained Clayey Soil
ASTM D 420 : 2018 Standard Guide for Site Characterization for Engineering Design and Construction Purposes
ASTM D 6911 : 2015 : REDLINE Standard Guide for Packaging and Shipping Environmental Samples for Laboratory Analysis
ASTM D 4944 : 2018 : REDLINE Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester
ASTM D 5493 : 2006 Standard Test Method for Permittivity of Geotextiles Under Load
ASTM D 5299 : 1999 : R2005 Standard Guide for Decommissioning of Groundwater Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities
ASTM D 2166/D2166M : 2016 : REDLINE Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
ASTM D 3839 : 2014 : REDLINE Standard Guide for Underground Installation of “Fiberglass” (Glass-Fiber Reinforced Thermosetting-Resin) Pipe
ASTM D 5858 : 1996 : R2015 Standard Guide for Calculating <emph type="ital">In Situ</emph> Equivalent Elastic Moduli of Pavement Materials Using Layered Elastic Theory
ASTM D 5490 : 1993 : EDT 1 Standard Guide for Comparing Ground-Water Flow Model Simulations to Site-Specific Information
ASTM D 6724 : 2004 : R2010 Standard Guide for Installation of Direct Push Groundwater Monitoring Wells
ASTM D 7699/D7699M : 2011 Standard Practice for Minimum Geospatial Data for Abandoned Mine Land Problem Areas, Planning Units, Keyword Features, and Project Sites
ASTM D 1241 : 2015 : REDLINE Standard Specification for Materials for Soil-Aggregate Subbase, Base, and Surface Courses
ASTM D 5920 : 2014 Standard Test Method [Analytical Procedure] for Tests of Anisotropic Unconfined Aquifers by Neuman Method
ASTM D 5716/D5716M : 2015 Standard Test Method for Measuring the Rate of Well Discharge by Circular Orifice Weir
ASTM D 6187 : 1997 : R2003 Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence
ASTM D 5126 : 2016 : EDT 1 Standard Guide for Comparison of Field Methods for Determining Hydraulic Conductivity in Vadose Zone
ASTM D 4404 : 2018 : REDLINE Standard Test Method for Determination of Pore Volume and Pore Volume Distribution of Soil and Rock by Mercury Intrusion Porosimetry
ASTM D 1883 : 2016 : REDLINE Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils
ASTM D 1557 : 2012 : EDT 1 Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft<sup>3</sup> (2,700 kN-m/m<sup>3</sup>))
ASTM E 2278 : 2013 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage
ASTM D 5978/D5978M : 2016 : REDLINE Standard Guide for Maintenance and Rehabilitation of Groundwater Monitoring Wells
ASTM E 2787 : 2011 : R2016 Standard Test Method for Determination of Thiodiglycol in Soil Using Pressurized Fluid Extraction Followed by Single Reaction Monitoring Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS)
ASTM D 5611 : 1994 : EDT 1 Standard Guide for Conducting a Sensitivity Analysis for a Ground-Water Flow Model Application
ASTM D 6285 : 1999 : R2012 : EDT 1 Standard Guide for Locating Abandoned Wells
ASTM D 5921 : 1996 : R2003 : EDT 1 Standard Practice for Subsurface Site Characterization of Test Pits for On-Site Septic Systems
ASTM D 5785 : 1995 : R2013 Standard Test Method for (Analytical Procedure) for Determining Transmissivity of Confined Nonleaky Aquifers by Underdamped Well Response to Instantaneous Change in Head (Slug Test)
ASTM D 5472/D5472M : 2014 Standard Test Method for Determining Specific Capacity and Estimating Transmissivity at the Control Well
ASTM D 7069 : 2004 : R2015 Standard Guide for Field Quality Assurance in a Groundwater Sampling Event
ASTM D 5298 : 2016 : REDLINE Standard Test Method for Measurement of Soil Potential (Suction) Using Filter Paper
ASTM D 7380 : 2015 : REDLINE Standard Test Method for Soil Compaction Determination at Shallow Depths Using 5-lb (2.3 kg) Dynamic Cone Penetrometer
ASTM D 6285 : 1999 Standard Guide for Locating Abandoned Wells
ASTM E 2531 : 2006 : EDT 1 Standard Guide for Development of Conceptual Site Models and Remediation Strategies for Light Nonaqueous-Phase Liquids Released to the Subsurface
ASTM D 6128 : 2016 : REDLINE Standard Test Method for Shear Testing of Bulk Solids Using the Jenike Shear Tester
ASTM D 5872 : 1995 : R2006 Standard Guide for Use of Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 6169/D6169M : 2013 : REDLINE Standard Guide for Selection of Soil and Rock Sampling Devices Used With Drill Rigs for Environmental Investigations
ASTM D 6034 : 2017 : REDLINE Standard Test Method (Analytical Procedure) for Determining the Efficiency of a Production Well in a Confined Aquifer from a Constant Rate Pumping Test
ASTM D 5753 : 2018 : REDLINE Standard Guide for Planning and Conducting Geotechnical Borehole Geophysical Logging
ASTM D 7069 : 2004 : R2010 Standard Guide for Field Quality Assurance in a Groundwater Sampling Event
ASTM D 7499/D7499M : 2009 Standard Test Method for Measuring Geosynthetic-Soil Resilient Interface Shear Stiffness
ASTM D 5777 : 2000 : R2006 Standard Guide for Using the Seismic Refraction Method for Subsurface Investigation
ASTM D 5981 : 1996 : R2002 Standard Guide for Calibrating a Ground-Water Flow Model Application
ASTM D 6519 : 2015 : REDLINE Standard Practice for Sampling of Soil Using the Hydraulically Operated Stationary Piston Sampler
ASTM D 5715 : 2014 : REDLINE Standard Practice for Estimating the Degree of Humification of Peat and Other Organic Soils (Visual/Manual Method)
ASTM D 6027/D6027M : 2015 Standard Practice for Calibrating Linear Displacement Transducers for Geotechnical Purposes
ASTM D 427 : 2004 Test Method for Shrinkage Factors of Soils by the Mercury Method (Withdrawn 2008)
ASTM D 5254 : 1992 : R2004 Standard Practice for Minimum Set of Data Elements to Identify a Ground-Water Site
ASTM D 5610 : 1994 : R2002 Standard Guide for Defining Initial Conditions in Ground-Water Flow Modeling
ASTM D 5880 : 1995 : R2006 Standard Guide for Subsurface Flow and Transport Modeling (Withdrawn 2015)
ASTM D 2113 : 2014 : REDLINE Standard Practice for Rock Core Drilling and Sampling of Rock for Site Exploration
ASTM D 7045 : 2017 : REDLINE Standard Guide for Optimization of Groundwater Monitoring Constituents for Detection Monitoring Programs for Waste Disposal Facilities
ASTM D 7099 : 2004 Standard Terminology Relating to Frozen Soil and Rock
ASTM D 6706 : 2001 : R2007 Standard Test Method for Measuring Geosynthetic Pullout Resistance in Soil
ASTM D 6938 : 2017-03 TEST METHOD FOR IN-PLACE DENSITY AND WATER CONTENT OF SOIL AND SOIL-AGGREGATE BY NUCLEAR METHODS (SHALLOW DEPTH)
ASTM D 5855 : 1995 : R2006 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in Flowing Well
ASTM D 7458 : 2014 : REDLINE Standard Test Method for Determination of Beryllium in Soil, Rock, Sediment, and Fly Ash Using Ammonium Bifluoride Extraction and Fluorescence Detection
ASTM D 7503 : 2018 : REDLINE Standard Test Method for Measuring the Exchange Complex and Cation Exchange Capacity of Inorganic Fine-Grained Soils
ASTM D 8038 : 2016 Standard Practice for Reclamation of Recycled Aggregate Base (RAB) Material
ASTM D 5268 : 2013 : REDLINE Standard Specification for Topsoil Used for Landscaping Purposes
ASTM D 7560 : 2016 Standard Test Method for Determination of Fiber Length Percentages in Hydraulic Erosion Control Products (HECPs)
ASTM D 5738 : 1995 : R2000 Standard Guide for Displaying the Results of Chemical Analyses of Ground Water for Major Ions and Trace Elements-Diagrams for Single Analyses
ASTM D 6429 : 1999 : R2011 : EDT 1 Standard Guide for Selecting Surface Geophysical Methods (Withdrawn 2020)
ASTM D 6168 : 1997 : R2010 Standard Guide for Selection of Minimum Set of Data Elements Required to Identify Locations Chosen for Field Collection of Information to Describe Soil, Rock, and Their Contained Fluids (Withdrawn 2019)
ASTM D 5611 : 1994 : R2008 Standard Guide for Conducting a Sensitivity Analysis for a Groundwater Flow Model Application
AASHTO TP 104 : 2013(R2015) METHOD OF TEST FOR RAPID AXIAL COMPRESSIVE LOAD TESTING OF DEEP FOUNDATION UNITS
ASTM D 4748 : 2010 Standard Test Method for Determining the Thickness of Bound Pavement Layers Using Short-Pulse Radar
ASTM D 6634/D6634M : 2014 : REDLINE Standard Guide for the Selection of Purging and Sampling Devices for Groundwater Monitoring Wells
ASTM D 7702/D7702M : 2014 : REDLINE Standard Guide for Considerations When Evaluating Direct Shear Results Involving Geosynthetics
ASTM D 5876 : 1995 : R2000 Standard Guide for Use of Direct Rotary Wireline Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 4511 : 2011 : REDLINE Standard Test Method for Hydraulic Conductivity of Essentially Saturated Peat
ASTM D 5312/D5312M : 2012 Standard Test Method for Evaluation of Durability of Rock for Erosion Control Under Freezing and Thawing Conditions
ASTM D 6168 : 1997 : R2004 Standard Guide for Selection of Minimum Set of Data Elements Required to Identify Locations Chosen for Field Collection of Information to Describe Soil, Rock, and Their Contained Fluids
ASTM D 7760 : 2018 : REDLINE Standard Test Method for Measurement of Hydraulic Conductivity of Materials Derived from Scrap Tires Using a Rigid Wall Permeameter
ASTM D 1997 : 2013 : REDLINE Standard Test Method for Laboratory Determination of the Fiber Content of Peat Samples by Dry Mass
ASTM D 6914 : 2004 : EDT 1 Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices
ASTM E 2866 : 2012 : R2016 Standard Test Method for Determination of Diisopropyl Methylphosphonate, Ethyl Methylphosphonic Acid, Isopropyl Methylphosphonic Acid, Methylphosphonic Acid and Pinacolyl Methylphosphonic Acid in Soil by Pressurized Fluid Extraction and Analyzed by Liquid Chromatography/Tandem Mass Spectrometry
ASTM D 7625 : 2010 Standard Test Method for Laboratory Determination of Abrasiveness of Rock Using the CERCHAR Method (Withdrawn 2019)
ASTM D 2973 : 2016 : REDLINE Standard Test Method for Total Nitrogen in Peat Materials
ASTM E 2856 : 2013 : REDLINE Standard Guide for Estimation of LNAPL Transmissivity
ASTM D 5473 : 1993 : R2006 Standard Test Method for (Analytical Procedure for) Analyzing the Effects of Partial Penetration of Control Well and Determining the Horizontal and Vertical Hydraulic Conductivity in a Nonleaky Confined Aquifer (Withdrawn 2015)
ASTM D 7648 : 2012 Standard Practice for Active Soil Gas Sampling for Direct Push or Manual-Driven Hand-Sampling Equipment
ASTM D 6706 : 2001 Standard Test Method for Measuring Geosynthetic Pullout Resistance in Soil
ASTM D 7758 : 2017 : REDLINE Standard Practice for Passive Soil Gas Sampling in the Vadose Zone for Source Identification, Spatial Variability Assessment, Monitoring, and Vapor Intrusion Evaluations
ASTM D 6146 : 1997 Standard Guide for Monitoring Aqueous Nutrients in Watersheds
ASTM D 3689/D3689M : 2007 : R2013 : EDT 1 Standard Test Methods for Deep Foundations Under Static Axial Tensile Load
ASTM D 6820 : 2018 Standard Guide for Use of the Time Domain Electromagnetic Method for Subsurface Site Characterization
ASTM D 5321/D5321M : 2017 : REDLINE TEST METHOD FOR DETERMINING THE SHEAR STRENGTH OF SOIL-GEOSYNTHETIC AND GEOSYNTHETIC-GEOSYNTHETIC INTERFACES BY DIRECT SHEAR
ASTM D 7928 : 2017 : REDLINE Standard Test Method for Particle-Size Distribution (Gradation) of Fine-Grained Soils Using the Sedimentation (Hydrometer) Analysis
ASTM D 6432 : 2011 : REDLINE Standard Guide for Using the Surface Ground Penetrating Radar Method for Subsurface Investigation
ASTM D 4611 : 2016 : REDLINE Standard Test Method for Specific Heat of Rock and Soil
ASTM D 5873 : 2014 : REDLINE Standard Test Method for Determination of Rock Hardness by Rebound Hammer Method
ASTM D 1587/D1587M : 2015 : REDLINE Standard Practice for Thin-Walled Tube Sampling of Fine-Grained Soils for Geotechnical Purposes
ASTM D 6461/D6461M : 2018 : REDLINE Standard Specifications for Silt Fence Materials
ASTM D 5254/D5254M : 1992 : R2010 : EDT 1 Standard Practice for Minimum Set of Data Elements to Identify a Groundwater Site (Withdrawn 2019)
ASTM D 5408 : 1993 : R1998 Standard Guide for Set of Data Elements to Describe a Ground-Water Site; Part One-Additional Identification Descriptors
ASTM D 6106 : 1997 : R2010 Standard Guide for Establishing Nomenclature of Groundwater Aquifers (Withdrawn 2019)
ASTM D 5922 : 1996 : EDT 1 Standard Guide for Analysis of Spatial Variation in Geostatistical Site Investigations
ASTM D 5887/D5887M : 2016 : REDLINE Standard Test Method for Measurement of Index Flux Through Saturated Geosynthetic Clay Liner Specimens Using a Flexible Wall Permeameter
ASTM D 5474 : 1993 : R2000 Standard Guide for Selection of Data Elements for Ground-Water Investigations
ASTM D 4750 : 1987 : R2001 Standard Test Method for Determining Subsurface Liquid Levels in a Borehole or Monitoring Well (Observation Well) (Withdrawn 2010)
ASTM D 5270 : 1996 : R2002 Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers
ASTM D 3155 : 2011 : REDLINE Standard Test Method for Lime Content of Uncured Soil-Lime Mixtures
ASTM D 4044 : 1996 Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifiers
ASTM D 5737/D5737M : 2014 : REDLINE Standard Guide for Methods for Measuring Well Discharge
ASTM D 7626 : 2010 Standard Test Methods for Determining the Organic Treat Loading of Organophilic Clay
ASTM D 5923 : 1996 : EDT 1 Standard Guide for Selection of Kriging Methods in Geostatistical Site Investigations
ASTM D 6141 : 2014-07 GUIDE FOR SCREENING CLAY PORTION AND INDEX FLUX OF GEOSYNTHETIC CLAY LINER (GCL) FOR CHEMICAL COMPATIBILITY TO LIQUIDS
ASTM D 6913/D6913M : 2017 : REDLINE Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 5409/D5409M : 1993 : R2010 : EDT 1 Standard Guide for Set of Data Elements to Describe a Groundwater Site; Part Two<char: emdash>Physical Descriptors (Withdrawn 2019)
AASHTO T 208 : 2015(R2019) METHOD OF TEST FOR UNCONFINED COMPRESSIVE STRENGTH OF COHESIVE SOIL
ASTM D 4491 : 1999 : REV A Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 5567 : 1994 : R1999 Standard Test Method for Hydraulic Conductivity Ratio (HCR) Testing of Soil/Geotextile Systems
ASTM D 2850 : 2015 : REDLINE Standard Test Method for Unconsolidated-Undrained Triaxial Compression Test on Cohesive Soils
ASTM D 7014 : 2018 : REDLINE Standard Practice for Installation of Double-Twisted Wire Mesh Gabions and Revet Mattresses
ASTM D 6033 : 2016 : REDLINE Standard Guide for Describing the Functionality of a Groundwater Modeling Code
ASTM D 5855/D5855M : 2015 : REDLINE Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in Flowing Well
ASTM D 7664 : 2010 Standard Test Methods for Measurement of Hydraulic Conductivity of Unsaturated Soils
ASTM D 6276 : 1999 : REV A : R2006 : EDT 1 Standard Test Method for Using pH to Estimate the Soil-Lime Proportion Requirement for Soil Stabilization (Withdrawn 2015)
ASTM D 5284 : 2009 : R2017 Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid
ASTM D 7100 : 2011 : REDLINE Standard Test Method for Hydraulic Conductivity Compatibility Testing of Soils with Aqueous Solutions
ASTM D 5912 : 1996 : EDT 1 Standard Test Method for (Analytical Procedure) Determining Hydraulic Conductivity of an Unconfined Aquifer by Overdamped Well Response to Instantaneous Change in Head (Slug)
AASHTO T 208 : 2015 METHOD OF TEST FOR UNCONFINED COMPRESSIVE STRENGTH OF COHESIVE SOIL
ASCE 34 01 : 2001 STANDARD GUIDELINES FOR ARTIFICIAL RECHARGE OF GROUND WATER
AASHTO T 296 : 2010 METHOD OF TEST FOR UNCONSOLIDATED, UNDRAINED COMPRESSIVE STRENGTH OF COHESIVE SOILS IN TRIAXIAL COMPRESSION
AASHTO T 298 : 2015 METHOD OF TEST FOR HIGH-STRAIN DYNAMIC TESTING OF PILES
ASTM D 6528 : 2017 Standard Test Method for Consolidated Undrained Direct Simple Shear Testing of Fine Grain Soils
ASTM D 7013 : 2004 Standard Guide for Nuclear Surface Moisture and Density Gauge Calibration Facility Setup
ASTM D 3282 : 2015 : REDLINE Standard Practice for Classification of Soils and Soil-Aggregate Mixtures for Highway Construction Purposes
AASHTO T 216 : 2007 METHOD OF TEST FOR ONE-DIMENSIONAL CONSOLIDATION PROPERTIES OF SOILS
ASTM D 7701 : 2011 Standard Test Method for Determining the Flow Rate of Water and Suspended Solids from a Geotextile Bag (Withdrawn 2020)
AASHTO TP 100 : 2012 METHOD OF TEST FOR DEEP FOUNDATION ELEMENTS UNDER BIDIRECTIONAL STATIC AXIAL COMPRESSIVE LOAD
ASTM D 5611 : 1994 : R2016 Standard Guide for Conducting a Sensitivity Analysis for a Groundwater Flow Model Application
ASTM D 4696 : 1992 : R2008 Standard Guide for Pore-Liquid Sampling from the Vadose Zone (Withdrawn 2017)
ASTM D 558 : 2011 : REDLINE Standard Test Methods for Moisture-Density (Unit Weight) Relations of Soil-Cement Mixtures
ASTM D 4221 : 2018 : REDLINE Standard Test Method for Dispersive Characteristics of Clay Soil by Double Hydrometer
ASTM D 5299 : 1999 Standard Guide for Decommissioning of Ground Water Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities
ASTM D 5567 : 1994 : R2006 Standard Test Method for Hydraulic Conductivity Ratio (HCR) Testing of Soil/Geotextile Systems
ASTM D 7929 : 2014 Standard Guide for Selection of Passive Techniques for Sampling Groundwater Monitoring Wells
ASTM D 5981 : 1996 : R2008 Standard Guide for Calibrating a Groundwater Flow Model Application (Withdrawn 2017)
ASTM D 4220 : 1995 : R2007 Standard Practices for Preserving and Transporting Soil Samples
ASTM D 4092 : 2007 : R2013 Standard Terminology for Plastics: Dynamic Mechanical Properties
ASTM E 2993 : 2016 Standard Guide for Evaluating Potential Hazard as a Result of Methane in the Vadose Zone
ASTM D 5877 : 1995 : R2000 Standard Guide for Displaying Results of Chemical Analyses of Ground Water for Major Ions and Trace Elements-Diagrams Based on Data Analytical Calculations
ASTM D 5855 : 1995 : R2000 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of a Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in a Flowing Well
ASTM D 6773 : 2016 : REDLINE Standard Test Method for Bulk Solids Using Schulze Ring Shear Tester
ASTM D 6235 : 2004 Standard Practice for Expedited Site Characterization of Vadose Zone and Ground Water Contamination at Hazardous Waste Contaminated Sites
ASTM D 6517 : 2000 : R2012 : EDT 1 Standard Guide for Field Preservation of Groundwater Samples
ASTM D 5719 : 2013 Standard Guide for Simulation of Subsurface Airflow Using Groundwater Flow Modeling Codes (Withdrawn 2022)
ASTM D 4554 : 2012 : REDLINE Standard Test Method for In Situ Determination of Direct Shear Strength of Rock Discontinuities
ASTM D 5785/D5785M : 2015 : REDLINE Standard Test Method for (Analytical Procedure) for Determining Transmissivity of Confined Nonleaky Aquifers by Underdamped Well Response to Instantaneous Change in Head (Slug Test)
ASTM D 5730 : 2004 Standard Guide for Site Characterization for Environmental Purposes With Emphasis on Soil, Rock, the Vadose Zone and Groundwater (Withdrawn 2013)
ASTM D 5777 : 2000 Standard Guide for Using the Seismic Refraction Method for Subsurface Investigation
ASTM D 4428/D4428M : 2014 : REDLINE Standard Test Methods for Crosshole Seismic Testing
ASTM D 6836 : 2016 : REDLINE Standard Test Methods for Determination of the Soil Water Characteristic Curve for Desorption Using Hanging Column, Pressure Extractor, Chilled Mirror Hygrometer, or Centrifuge
ASTM D 5567 : 1994 : R2001 Standard Test Method for Hydraulic Conductivity Ratio (HCR) Testing of Soil/Geotextile Systems
ASTM D 5876/D5876M : 2017 : REDLINE Standard Guide for Use of Direct Rotary Wireline Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 5607 : 2016 : REDLINE Standard Test Method for Performing Laboratory Direct Shear Strength Tests of Rock Specimens Under Constant Normal Force
ASTM D 6066 : 2011 : REDLINE Standard Practice for Determining the Normalized Penetration Resistance of Sands for Evaluation of Liquefaction Potential
ASTM D 4633 : 2016 : REDLINE Standard Test Method for Energy Measurement for Dynamic Penetrometers
ASTM D 4403 : 2012 Standard Practice for Extensometers Used in Rock
ASTM D 5855 : 1995 : R2013 Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Confined Nonleaky or Leaky Aquifer by Constant Drawdown Method in Flowing Well
ASTM D 6913 : 2004 : R2009 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 6230 : 2013 : REDLINE Standard Test Method for Monitoring Ground Movement Using Probe-Type Inclinometers
ASTM D 6913 : 2004 : EDT 2 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 7608 : 2010 Standard Test Method for Torsional Ring Shear Test to Determine Drained Fully Softened Shear Strength and Nonlinear Strength Envelope of Cohesive Soils (Using Normally Consolidated Specimen) for Slopes with No Preexisting Shear Surfaces
ASTM D 4696 : 1992 : R2000 Standard Guide for Pore-Liquid Sampling from the Vadose Zone
ASTM D 6282/D6282M : 2014 Standard Guide for Direct Push Soil Sampling for Environmental Site Characterizations (Withdrawn 2023)
ASTM D 5781 : 1995 : R2006 Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 5924 : 1996 : R2004 Standard Guide for Selection of Simulation Approaches in Geostatistical Site Investigations
ASTM D 6391 : 2011 : REDLINE Standard Test Method for Field Measurement of Hydraulic Conductivity Using Borehole Infiltration
ASTM D 6429 : 1999 : R2006 Standard Guide for Selecting Surface Geophysical Methods
ASTM D 5737 : 1995 : R2006 Standard Guide for Methods for Measuring Well Discharge
ASTM D 6168 : 1997 : EDT 1 Standard Guide for Selection of the Minimum Set of Data Elements Required to Identify Locations Chosen for the Field Collection of Information to Describe Soil, Rock, and Their Contained Fluids
ASTM D 5754 : 1995 : R2006 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements<char: emdash>Trilinear Diagrams for Two or More Analyses (Withdrawn 2015)
ASTM D 2435 : 2004 Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading
ASTM D 5299/D5299M : 2018 : REDLINE Standard Guide for Decommissioning of Groundwater Wells, Vadose Zone Monitoring Devices, Boreholes, and Other Devices for Environmental Activities
ASTM D 6473 : 2015 : REDLINE Standard Test Method For Specific Gravity And Absorption of Rock For Erosion Control
ASTM D 6640 : 2001 Standard Practice for Collection and Handling of Soils Obtained in Core Barrel Samplers for Environmental Investigations
ASTM D 806 : 2011 : REDLINE Standard Test Method for Cement Content of Hardened Soil-Cement Mixtures
ASTM D 5121 : 2015 : REDLINE Standard Practice for Preparation of Rock Slabs for Durability Testing
ASTM D 6910 : 2004 Standard Test Method for Marsh Funnel Viscosity of Clay Construction Slurries
ASTM D 6517 : 2000 Standard Guide for Field Preservation of Ground-Water Samples
ASTM D 560 : 2003 Standard Test Methods for Freezing and Thawing Compacted Soil-Cement Mixtures (Withdrawn 2012)
ASTM D 4220/D4220M : 2014 : REDLINE Standard Practices for Preserving and Transporting Soil Samples
ASTM D 5786 : 2017 : REDLINE Standard Practice for (Field Procedure) for Constant Drawdown Tests in Flowing Wells for Determining Hydraulic Properties of Aquifer Systems
ASTM D 2664 : 2004 Standard Test Method for Triaxial Compressive Strength of Undrained Rock Core Specimens Without Pore Pressure Measurements (Withdrawn 2005)
ASTM D 6032/D6032M : 2017 : REDLINE Standard Test Method for Determining Rock Quality Designation (RQD) of Rock Core
ASTM D 4083 : 1989 : R1994 : EDT 2 Standard Practice for Description of Frozen Soils (Visual-Manual Procedure)
ASTM D 6565 : 2000 Standard Test Method for Determination of Water (Moisture) Content of Soil by the Time-Domain Reflectometry (TDR) Method
ASTM D 2977 : 2014 Standard Practice for Particle Size Range of Peat Materials for Horticultural Purposes
ASTM D 8169/D8169M : 2018 Standard Test Methods for Deep Foundations Under Bi-Directional Static Axial Compressive Load
ASTM D 5787 : 2014 : REDLINE Standard Practice for Monitoring Well Protection
ASTM D 5856 : 2015 : REDLINE Standard Test Method for Measurement of Hydraulic Conductivity of Porous Material Using a Rigid-Wall, Compaction-Mold Permeameter
ASTM D 5490 : 1993 : R2014 : EDT 1 Standard Guide for Comparing Groundwater Flow Model Simulations to Site-Specific Information (Withdrawn 2023)
ASTM D 6564/D6564M : 2017 : REDLINE Standard Guide for Field Filtration of Groundwater Samples
ASTM D 7780 : 2012 Standard Practice for Geospatial Data for Representing Coal Mining Features
ASTM D 6629 : 2001 Standard Guide for Selection of Methods for Estimating Soil Loss by Erosion
ASTM D 7481 : 2009 Standard Test Methods for Determining Loose and Tapped Bulk Densities of Powders using a Graduated Cylinder (Withdrawn 2018)
ASTM D 4050 : 2014 : REDLINE Standard Test Method for (Field Procedure) for Withdrawal and Injection Well Testing for Determining Hydraulic Properties of Aquifer Systems
ASTM D 4643 : 2017 : REDLINE Standard Test Method for Determination of Water Content of Soil and Rock by Microwave Oven Heating
ASTM D 5220 : 2014 : REDLINE Standard Test Method for Water Mass per Unit Volume of Soil and Rock In-Place by the Neutron Depth Probe Method
ASTM D 5493 : 2006 : R2011 Standard Test Method for Permittivity of Geotextiles Under Load
ASTM C 1127/C1127M : 2015 : REDLINE Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface
ASTM D 6727 : 2001 : R2007 Standard Guide for Conducting Borehole Geophysical Logging<char: emdash>Neutron
ASTM D 6724/D6724M : 2016 : REDLINE Standard Guide for Installation of Direct Push Groundwater Monitoring Wells
ASTM E 2787 : 2011 Standard Test Method for Determination of Thiodiglycol in Soil Using Pressurized Fluid Extraction Followed by Single Reaction Monitoring Liquid Chromatography/Tandem Mass Spectrometry (LC/MS/MS)
ASTM D 7242 : 2006 Standard Practice for Field Pneumatic Slug (Instantaneous Change in Head) Tests to Determine Hydraulic Properties of Aquifers with Direct Push Groundwater Samplers
ASTM D 7262 : 2010 : R2016 : EDT 1 Standard Test Method for Estimating the Permanganate Natural Oxidant Demand of Soil and Aquifer Solids
ASTM D 7263 : 2009 Standard Test Methods for Laboratory Determination of Density (Unit Weight) of Soil Specimens
ASTM D 7367 : 2014-06 TEST METHOD FOR DETERMINING WATER HOLDING CAPACITY OF FIBER MULCHES FOR HYDRAULIC PLANTING
ASTM D 5567 : 1994 : R2011 Standard Test Method for Hydraulic Conductivity Ratio (HCR) Testing of Soil/Geotextile Systems
ASTM D 5240 : 2004 Standard Test Method for Testing Rock Slabs to Evaluate Soundness of Riprap by Use of Sodium Sulfate or Magnesium Sulfate
ASTM D 6088 : 2006 : R2011 Standard Practice for Installation of Geocomposite Pavement Drains
ASTM D 5610 : 1994 : R2014 Standard Guide for Defining Initial Conditions in Groundwater Flow Modeling (Withdrawn 2023)
AASHTO TP 104:2013 Standard Method of Test for Rapid Axial Compressive Load Testing of Deep Foundation Units
ASTM D 5240/D5240M : 2013-05 STANDARD TEST METHOD FOR EVALUATION OF DURABILITY OF ROCK FOR EROSION CONTROL USING SODIUM SULFATE OR MAGNESIUM SULFATE
ASTM D 7263 : 2009 : R2018 Standard Test Methods for Laboratory Determination of Density (Unit Weight) of Soil Specimens
ASCE 36 01 : 2001 STANDARD CONSTRUCTION GUIDELINES FOR MICROTUNNELING
ASTM D 7322/D7322M : 2017 : REDLINE Standard Test Method for Determination of Erosion Control Product (ECP) Ability to Encourage Seed Germination and Plant Growth Under Bench-Scale Conditions
ASTM D 1587 : 2008 Standard Practice for Thin-Walled Tube Sampling of Soils for Geotechnical Purposes
ASTM D 5092/D5092M : 2016 : REDLINE Standard Practice for Design and Installation of Groundwater Monitoring Wells
ASTM F 1759 : 1997 : R2018 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
ASTM D 4395 : 2017 : REDLINE Standard Test Method for Determining In Situ Modulus of Deformation of Rock Mass Using Flexible Plate Loading Method
ASTM D 3966/D3966M : 2007 : R2013 : EDT 1 Standard Test Methods for Deep Foundations Under Lateral Load
ASTM D 6727 : 2001 Standard Guide for Conducting Borehole Geophysical Logging-Neutron
ASTM D 6475 : 2017 Standard Test Method for Measuring Mass per Unit Area of Erosion Control Blankets
ASTM D 6431 : 2018 : REDLINE Standard Guide for Using the Direct Current Resistivity Method for Subsurface Site Characterization
ASTM D 5979 : 1996 : R2002 Standard Guide for Conceptualization and Characterization of Ground-Water Systems
ASTM D 4793 : 2009 : R2017 Standard Test Method for Sequential Batch Extraction of Waste with Water
ASTM D 4520 : 2013-03 PRACTICE FOR DETERMINING WATER INJECTIVITY THROUGH THE USE OF ON-SITE FLOODS
ASTM D 4043 : 2017 : REDLINE Standard Guide for Selection of Aquifer Test Method in Determining Hydraulic Properties by Well Techniques
ASTM D 6030 : 2015 : REDLINE Standard Guide for Selection of Methods for Assessing Groundwater or Aquifer Sensitivity and Vulnerability
ASTM D 7300 : 2012-01 TEST METHOD FOR LABORATORY DETERMINATION OF STRENGTH PROPERTIES OF FROZEN SOIL AT A CONSTANT RATE OF STRAIN
ASTM D 4750 : 1987 : R1993 : EDT 1 Standard Test Method for Determining Subsurface Liquid Levels in a Borehole or Monitoring Well (Observation Well)
ASTM D 5101 : 2012 Standard Test Method for Measuring the Filtration Compatibility of Soil-Geotextile Systems
ASTM D 2487 : 2017 : REDLINE Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
ASTM E 2243 : 2013 Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Re-contouring and Highwall Reclamation
ASTM D 5335 : 2014 : REDLINE Standard Test Method for Linear Coefficient of Thermal Expansion of Rock Using Bonded Electric Resistance Strain Gauges
ASTM D 4491 : 1999 : REV A : R2004 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 6780/D6780M : 2012 : REDLINE Standard Test Method for Water Content and Density of Soil In situ by Time Domain Reflectometry (TDR)
ASTM D 4542 : 2015 : REDLINE Standard Test Methods for Pore Water Extraction and Determination of the Soluble Salt Content of Soils by Refractometer
ASTM D 4106 : 2015 : REDLINE Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method
ASTM D 5876 : 1995 : R2012 : EDT 1 Standard Guide for Use of Direct Rotary Wireline Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 6780 : 2005 Standard Test Method for Water Content and Density of Soil in Place by Time Domain Reflectometry (TDR)
ASTM D 3441 : 2016 Standard Test Method for Mechanical Cone Penetration Testing of Soils
ASTM D 4491 : 1999 : REV A : R2014 : EDT 1 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 1587 : 2008 : R2012 : EDT 1 Standard Practice for Thin-Walled Tube Sampling of Soils for Geotechnical Purposes
ASTM D 7481 : 2018 Standard Test Methods for Determining Loose and Tapped Bulk Densities of Powders using a Graduated Cylinder
ASTM D 4223/D4223M : 2012 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
ASTM D 6001 : 2005 : R2012 Standard Guide for Direct-Push Groundwater Sampling for Environmental Site Characterization
ASTM D 4220 : 1995 : R2000 Standard Practices for Preserving and Transporting Soil Samples
ASTM D 7242/D7242M : 2006 : R2013 : EDT 1 Standard Practice for Field Pneumatic Slug (Instantaneous Change in Head) Tests to Determine Hydraulic Properties of Aquifers with Direct Push Groundwater Samplers (Withdrawn 2022)
ASTM D 6285 : 1999 : R2016 Standard Guide for Locating Abandoned Wells
ASTM D 3148 : 2002 Standard Test Method for Elastic Moduli of Intact Rock Core Specimens in Uniaxial Compression (Withdrawn 2005)
ISO 17312:2005 Soil quality Determination of hydraulic conductivity of saturated porous materials using a rigid-wall permeameter
ASTM D 5610 : 1994 : EDT 1 Standard Guide for Defining Initial Conditions in Ground-Water Flow Modeling
ASTM D 7262 : 2010 Standard Test Method for Estimating the Permanganate Natural Oxidant Demand of Soil and Aquifer Solids
ASTM D 6286 : 2012 : REDLINE Standard Guide for Selection of Drilling Methods for Environmental Site Characterization
ASTM D 5978 : 1996 : EDT 1 Standard Guide for Maintenance and Rehabilitation of Ground-Water Monitoring Wells
ASTM D 4083 : 1989 : R2016 Standard Practice for Description of Frozen Soils (Visual-Manual Procedure)
ASTM D 5979 : 1996 : R2008 Standard Guide for Conceptualization and Characterization of Groundwater Systems
ASTM D 5233 : 1992 : R2004 Standard Test Method for Single Batch Extraction Method for Wastes
ASTM D 4405 : 2004 Standard Test Method for Creep of Cylindrical Soft Rock Core Specimens in Uniaxial Compressions (Withdrawn 2005)
ASTM F 2536 : 2017 : REDLINE Standard Guide for Installing Plastic DWV Piping Suspended from On-Grade Slabs
ASTM D 7013/D7013M : 2015 : REDLINE Standard Guide for Calibration Facility Setup for Nuclear Surface Gauges
ASTM D 6760 : 2016 : REDLINE Standard Test Method for Integrity Testing of Concrete Deep Foundations by Ultrasonic Crosshole Testing
ASTM D 6102 : 2015 : REDLINE Standard Guide for Installation of Geosynthetic Clay Liners
ASTM D 5609 : 2016 : REDLINE Standard Guide for Defining Boundary Conditions in Groundwater Flow Modeling
ASTM D 1633 : 2017 Standard Test Methods for Compressive Strength of Molded Soil-Cement Cylinders
ASTM D 2167 : 2015 : REDLINE Standard Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method
ASTM D 6036 : 1996 : R2014 Standard Guide for Displaying the Results of Chemical Analyses of Groundwater for Major Ions and Trace Elements—Use of Maps (Withdrawn 2023)
ASTM D 2419 : 2014 : REDLINE Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
ASTM D 5921 : 1996 : R2010 Standard Practice for Subsurface Site Characterization of Test Pits for On-Site Septic Systems (Withdrawn 2019)
ASTM D 6629 : 2001 : R2012 : EDT 1 Standard Guide for Selection of Methods for Estimating Soil Loss by Erosion (Withdrawn 2019)
ASTM F 1953 : 2010 Standard Guide for Construction and Maintenance of Grass Tennis Courts
ASTM D 5202/D5202M : 2016 : REDLINE Standard Test Method for Determining Triaxial Compression Creep Strength of Chemically Grouted Soils
ASTM D 5474 : 1993 : R2012 Standard Guide for Selection of Data Elements for Groundwater Investigations (Withdrawn 2021)
ASTM D 5610 : 1994 : R2008 Standard Guide for Defining Initial Conditions in Groundwater Flow Modeling
ASTM D 6001 : 2005 Standard Guide for Direct-Push Groundwater Sampling for Environmental Site Characterization
ASTM D 6640 : 2001 : R2005 Standard Practice for Collection and Handling of Soils Obtained in Core Barrel Samplers for Environmental Investigations
ASTM D 7099 : 2004 : R2010 Standard Terminology Relating to Frozen Soil and Rock
ASTM D 6035/D6035M : 2013 : REDLINE Standard Test Method for Determining the Effect of Freeze-Thaw on Hydraulic Conductivity of Compacted or Intact Soil Specimens Using a Flexible Wall Permeameter
ASTM D 6640 : 2001 : R2010 Standard Practice for Collection and Handling of Soils Obtained in Core Barrel Samplers for Environmental Investigations
ASTM D 5872 : 1995 : R2000 Standard Guide for Use of Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 3080/D3080M : 2011 : REDLINE Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions (Withdrawn 2020)
ASTM D 6539 : 2013 : REDLINE Standard Test Method for Measurement of the Permeability of Unsaturated Porous Materials by Flowing Air
ASTM D 4491/D4491M : 2017 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 5779/D5779M : 2014 : REDLINE Standard Test Method for Field Determination of Rapid Specific Gravity of Rock and Manmade Materials for Erosion Control
ASTM D 1143/D1143M : 2007 : EDT 1 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load
ASTM D 6914/D6914M : 2016 : REDLINE Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices
ASTM D 1143/D1143M : 2007 : R2013 : EDT 1 Standard Test Methods for Deep Foundations Under Static Axial Compressive Load
ASTM D 7207 : 2005 Standard Test Method for Determination of Unvegetated Rolled Erosion Control Product (RECP) Ability to Protect Sand from Hydraulically-Induced Shear Stresses under Bench-Scale Conditions (Withdrawn 2014)
ASTM D 5882 : 2016 : REDLINE Standard Test Method for Low Strain Impact Integrity Testing of Deep Foundations
ASTM D 6727/D6727M : 2016 : REDLINE Standard Guide for Conducting Borehole Geophysical Logging—Neutron
ASTM D 5781 : 1995 : R2000 Standard Guide for Use of Dual-Wall Reverse-Circulation Drilling for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 5254 : 1992 : R1998 Standard Practice for Minimum Set of Data Elements to Identify a Ground-Water Site
ASTM D 6429 : 1999 Standard Guide for Selecting Surface Geophysical Methods
ASTM D 4767 : 2011 : REDLINE Standard Test Method for Consolidated Undrained Triaxial Compression Test for Cohesive Soils
ASTM D 6564 : 2000 : R2005 Standard Guide for Field Filtration of Groundwater Samples
ASTM D 6914 : 2004 : R2010 Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices
ASTM D 5284 : 2009 Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid
ASTM D 7743 : 2012 Standard Test Method for Measuring the Minimum Fluidization Velocities of Free Flowing Powders
ASTM D 5981/D5981M : 2018 Standard Guide for Calibrating a Groundwater Flow Model Application
ASTM D 6453 : 1999 Standard Guide for Format of Computerized Exchange of Soil and Rock Test Data (Withdrawn 2008)
ASTM D 7949 : 2014 Standard Test Methods for Thermal Integrity Profiling of Concrete Deep Foundations (Withdrawn 2023)
ASTM F 1759 : 1997 : R2010 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
ASTM D 6024/D6024M : 2016 : REDLINE Standard Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application
ASTM F 1759 : 1997 Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
ASTM D 5921 : 1996 : EDT 1 Standard Practice for Subsurface Site Characterization of Test Pits for On-Site Septic Systems
ASTM D 6629 : 2001 : R2007 Standard Guide for Selection of Methods for Estimating Soil Loss by Erosion
ASTM D 6639 : 2018 Standard Guide for Using the Frequency Domain Electromagnetic Method for Subsurface Site Characterizations
ASTM D 6913 : 2004 : R2009 : EDT 1 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 6452 : 1999 : R2012 : EDT 1 Standard Guide for Purging Methods for Wells Used for Groundwater Quality Investigations
ASTM D 7048 : 2016 : REDLINE Standard Guide for Applying Statistical Methods for Assessment and Corrective Action Environmental Monitoring Programs
ASTM D 5979 : 1996 : R2014 Standard Guide for Conceptualization and Characterization of Groundwater Systems
ASTM D 6187 : 1997 Standard Practice for Cone Penetrometer Technology Characterization of Petroleum Contaminated Sites with Nitrogen Laser-Induced Fluorescence
ASTM D 6459 : 2015 : REDLINE Standard Test Method for Determination of Rolled Erosion Control Product (RECP) Performance in Protecting Hillslopes from Rainfall-Induced Erosion
ASTM D 4092 :2007 Standard Terminology: Plastics: Dynamic Mechanical Properties
ASTM D 4452 : 2014 : REDLINE Standard Practice for X-Ray Radiography of Soil Samples
ASTM D 5778 : 2012 : REDLINE Standard Test Method for Electronic Friction Cone and Piezocone Penetration Testing of Soils
ASTM D 4381/D4381M : 2012 : REDLINE Standard Test Method for Sand Content by Volume of Bentonitic Slurries (Withdrawn 2021)
ASTM D 5923 : 1996 : R2010 Standard Guide for Selection of Kriging Methods in Geostatistical Site Investigations
ASTM D 5474 : 1993 : R2006 Standard Guide for Selection of Data Elements for Groundwater Investigations
ASTM D 6725/D6725M : 2016 : REDLINE Standard Practice for Direct Push Installation of Prepacked Screen Monitoring Wells in Unconsolidated Aquifers
ASTM D 4829 : 2011 : REDLINE Standard Test Method for Expansion Index of Soils
ASTM D 5971/D5971M : 2016 : REDLINE Standard Practice for Sampling Freshly Mixed Controlled Low-Strength Material
ASTM D 8006 : 2016 Standard Guide for Sampling and Analysis of Residential and Commercial Water Supply Wells in Areas of Exploration and Production (E&P) Operations
ASTM E 2060 : 2006 : R2014 Standard Guide for Use of Coal Combustion Products for Solidification/Stabilization of Inorganic Wastes
ASTM D 3967 : 2016 : REDLINE Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens
ASTM D 6235 : 2004 : R2010 Standard Practice for Expedited Site Characterization of Vadose Zone and Groundwater Contamination at Hazardous Waste Contaminated Sites
ASTM D 1452/D1452M : 2016 : REDLINE Standard Practice for Soil Exploration and Sampling by Auger Borings
ASTM D 5408 : 1993 : R2010 : EDT 1 Standard Guide for Set of Data Elements to Describe a Groundwater Site;<br> Part One<char: emdash>Additional Identification Descriptors (Withdrawn 2019)
ASTM D 6027 : 1996 : R2004 Standard Test Method for Calibrating Linear Displacement Transducers for Geotechnical Purposes (Withdrawn 2013)
ASTM D 6151/D6151M : 2015 : REDLINE Standard Practice for Using Hollow-Stem Augers for Geotechnical Exploration and Soil Sampling
ASTM D 5270 : 1996 : R2008 Standard Test Method for Determining Transmissivity and Storage Coefficient of Bounded, Nonleaky, Confined Aquifers
ASTM D 7128 : 2005 Standard Guide for Using the Seismic-Reflection Method for Shallow Subsurface Investigation
ASTM D 6282 : 1998 Standard Guide for Direct Push Soil Sampling for Environmental Site Characterizations
ASTM D 5876 : 1995 : R2005 Standard Guide for Use of Direct Rotary Wireline Casing Advancement Drilling Methods for Geoenvironmental Exploration and Installation of Subsurface Water-Quality Monitoring Devices
ASTM D 5550 : 2014 : REDLINE Standard Test Method for Specific Gravity of Soil Solids by Gas Pycnometer
ASTM D 4083 : 1989 : R2007 Standard Practice for Description of Frozen Soils (Visual-Manual Procedure)
ASTM D 5912 : 1996 : R2004 Standard Test Method for (Analytical Procedure) Determining Hydraulic Conductivity of an Unconfined Aquifer by Overdamped Well Response to Instantaneous Change in Head (Slug) (Withdrawn 2013)
ASTM D 559 : 2003 Standard Test Methods for Wetting and Drying Compacted Soil-Cement Mixtures (Withdrawn 2012)
ASTM D 7352 : 2007 : R2012 Standard Practice for Direct Push Technology for Volatile Contaminant Logging with the Membrane Interface Probe (MIP)
ASTM D 7013 : 2004 : EDT 1 Standard Guide for Nuclear Surface Moisture and Density Gauge Calibration Facility Setup
ASTM D 4044 : 1996 : R2008 Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifers
ASTM D 7880/D7880M : 2013 Standard Test Method for Determining Flow Rate of Water and Suspended Solids Retention from a Closed Geosynthetic Bag (Withdrawn 2022)
ASTM D 5333 : 2003 Standard Test Method for Measurement of Collapse Potential of Soils (Withdrawn 2012)
ASTM D 1635/D1635M : 2012 Standard Test Method for Flexural Strength of Soil-Cement Using Simple Beam with Third-Point Loading
ASTM D 5754 : 1995 : R2000 Standard Guide for Displaying the Results of Chemical Analyses of Ground Water for Major Ions and Trace Elements-Trilinear Diagrams for Two or More Analyses
ASTM D 6565 : 2000 : R2005 Standard Test Method for Determination of Water (Moisture) Content of Soil by the Time-Domain Reflectometry (TDR) Method (Withdrawn 2014)
ASTM D 5785 : 1995 : R2006 Standard Test Method for (Analytical Procedure) for Determining Transmissivity of Confined Nonleaky Aquifers by Underdamped Well Response to Instantaneous Change in Head (Slug Test)
ASTM D 6766 : 2018 : REDLINE Standard Test Method for Evaluation of Hydraulic Properties of Geosynthetic Clay Liners Permeated with Potentially Incompatible Aqueous Solutions
ASTM D 6029 : 2017 : REDLINE Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer and a Leaky Confining Bed with Negligible Storage by the Hantush-Jacob Method
ASTM D 5519 : 2015 : REDLINE Standard Test Methods for Particle Size Analysis of Natural and Man-Made Riprap Materials
ASTM D 4959 : 2016 : REDLINE Standard Test Method for Determination of Water Content of Soil By Direct Heating
ASTM D 3080 : 2004 Standard Test Method for Direct Shear Test of Soils Under Consolidated Drained Conditions
ASTM D 6036 : 1996 : R2002 Standard Guide for Displaying the Results of Chemical Analyses of Ground Water for Major Ions and Trace Elements—Use of Maps
ASTM D 6527 : 2000 : R2008 Standard Test Method for Determining Unsaturated and Saturated Hydraulic Conductivity in Porous Media by Steady-State Centrifugation (Withdrawn 2017)
ASTM D 7070 : 2016 : REDLINE Standard Test Methods for Creep of Rock Core Under Constant Stress and Temperature
ASTM D 7272 : 2006 : R2011 Standard Test Method for Determining the Integrity of Seams Used in Joining Geomembranes by Pre-manufactured Taped Methods
ASTM D 6572 : 2014-02 TEST METHODS FOR DETERMINING DISPERSIVE CHARACTERISTICS OF CLAYEY SOILS BY THE CRUMB TEST
ASTM D 6726 : 2015 : REDLINE Standard Guide for Conducting Borehole Geophysical Logging—Electromagnetic Induction
ASTM D 1634 : 2017 Standard Test Method for Compressive Strength of Soil-Cement Using Portions of Beams Broken in Flexure (Modified Cube Method)
ASTM D 5409 : 1993 : R2004 Standard Guide for Set of Data Elements to Describe a Ground-Water Site; Part Two-Physical Descriptors
ASTM D 4044/D4044M : 2015 : REDLINE Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifers
ASTM D 2976 : 2015 Standard Test Method for pH of Peat Materials
ASTM D 4491 : 1999 : REV A : R2009 Standard Test Methods for Water Permeability of Geotextiles by Permittivity
ASTM D 5981 : 1996 : EDT 1 Standard Guide for Calibrating a Ground-Water Flow Model Application
ASTM D 6914 : 2004 Standard Practice for Sonic Drilling for Site Characterization and the Installation of Subsurface Monitoring Devices
ASTM D 4341 : 2003 Standard Test Method for Creep of Cylindrical Hard Rock Core Specimens in Uniaxial Compression (Withdrawn 2005)
ASTM D 5717 : 1995 : EDT 1 Standard Guide for Design of Ground-Water Monitoring Systems in Karst and Fractured-Rock Aquifers (Withdrawn 2005)
ASTM D 5978 : 1996 : R2005 Standard Guide for Maintenance and Rehabilitation of Groundwater Monitoring Wells
ASTM D 4380 : 2012 : REDLINE Standard Test Method for Density of Bentonitic Slurries
ASTM D 7338 : 2014 : REDLINE Standard Guide for Assessment Of Fungal Growth in Buildings
ASTM D 6171 : 1997 : R2004 Standard Guide for Documenting a Ground-Water Modeling Code
ASTM D 4647/D4647M : 2013 : REDLINE Standard Test Methods for Identification and Classification of Dispersive Clay Soils by the Pinhole Test
ASME NQA 2 : 89 SPECIAL NOTICE QUALITY ASSURANCE REQUIREMENTS FOR NUCLEAR FACILITY APPLICATIONS

ASTM D 4106 : 2015 : REDLINE Standard Test Method for (Analytical Procedure) for Determining Transmissivity and Storage Coefficient of Nonleaky Confined Aquifers by the Theis Nonequilibrium Method
ASTM D 5269 : 2015 : REDLINE Standard Test Method for Determining Transmissivity of Nonleaky Confined Aquifers by the Theis Recovery Method
ASTM D 4043 : 2017 : REDLINE Standard Guide for Selection of Aquifer Test Method in Determining Hydraulic Properties by Well Techniques
ASTM D 4044 : 1996 Standard Test Method for (Field Procedure) for Instantaneous Change in Head (Slug) Tests for Determining Hydraulic Properties of Aquifiers
ASTM D 4104 : 1996 Standard Test Method (Analytical Procedure) for Determining Transmissivity of Nonleaky Confined Aquifers by Overdamped Well Response to Instantaneous Change in Head (Slug Tests)
ASTM D 1883 : 2016 : REDLINE Standard Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils
ASTM C 802 : 2014 : REDLINE Standard Practice for Conducting an Interlaboratory Test Program to Determine the Precision of Test Methods for Construction Materials
ASTM D 854 : 2014 : REDLINE Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer (Withdrawn 2023)
ASTM D 698 : 2013-05 TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3]))
ASTM D 4254 : 2016 : REDLINE Standard Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
ASTM D 4050 : 2014 : REDLINE Standard Test Method for (Field Procedure) for Withdrawal and Injection Well Testing for Determining Hydraulic Properties of Aquifer Systems
ASTM D 558 : 2011 : REDLINE Standard Test Methods for Moisture-Density (Unit Weight) Relations of Soil-Cement Mixtures
ASTM D 2435 : 2004 Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading
ASTM D 6029 : 2017 : REDLINE Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer and a Leaky Confining Bed with Negligible Storage by the Hantush-Jacob Method
ASTM D 4253 : 2016 : REDLINE Standard Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
ASTM D 6312 : 2017 : REDLINE Standard Guide for Developing Appropriate Statistical Approaches for Groundwater Detection Monitoring Programs at Waste Disposal Facilities
ASTM D 6026 : 2013 : REDLINE Standard Practice for Using Significant Digits in Geotechnical Data
ASTM D 6913 : 2004 : EDT 2 Standard Test Methods for Particle-Size Distribution (Gradation) of Soils Using Sieve Analysis
ASTM D 6028 : 2017 : REDLINE Standard Test Method (Analytical Procedure) for Determining Hydraulic Properties of a Confined Aquifer Taking into Consideration Storage of Water in Leaky Confining Beds by Modified Hantush Method

View more information
$195.89
Including GST where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Need help?
Call us on 131 242, then click here to start a Screen Sharing session
so we can help right away! Learn more