DIN EN ISO 10407-2:2010-08
Current
The latest, up-to-date edition.
PETROLEUM AND NATURAL GAS INDUSTRIES - ROTARY DRILLING EQUIPMENT - PART 2: INSPECTION AND CLASSIFICATION OF USED DRILL STEM ELEMENTS
Hardcopy , PDF
German
01-01-2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
4.1 Symbols
4.2 Abbreviated terms
5 Conformance
5.1 Basis for inspection
5.2 Repeatability of results
5.3 Ordering information
6 Quality assurance
6.1 General
6.2 Standardization and operating procedures
6.3 Equipment description
6.4 Personnel qualification
6.5 Dynamic test data demonstrating the system
capabilities for detecting the reference
indicators
6.6 Reports
7 Qualification of inspection personnel
7.1 General
7.2 Written procedure
7.3 Qualification responsibility and requirements
7.4 Training programmes
7.5 Examinations
7.6 Experience
7.7 Re-qualification
7.8 Documentation
7.9 NDT personnel certification
8 General inspection procedures
8.1 General
8.2 Owner/operator work site requirements for
quality inspection
8.3 Documents at job site
8.4 Pre-inspection procedures
8.5 Drill-pipe and tool-joint classification
markings
8.6 Post-inspection procedures
9 General non-destructive inspection method requirements
9.1 General
9.2 Equipment
9.3 Illumination
9.4 Magnetic-particle-inspection equipment
9.5 Ultrasonic
9.6 Electromagnetic inspection units
10 Drill stem element inspection and classification
10.1 Pipe body - Full-length visual inspection
10.2 Drill body - Outside diameter gauging
10.3 Pipe body - Ultrasonic wall-thickness gauging
10.4 Pipe body - Full-length electromagnetic
inspection (EMI)
10.5 Pipe body - Full-length ultrasonic transverse
and wall thickness
10.6 Pipe body - Full-length ultrasonic transverse,
wall thickness and longitudinal inspection
10.7 Drill-pipe body - External magnetic-particle
inspection of the critical area
10.8 Drill-pipe body - Bi-directional external
magnetic-particle inspection of the critical
area
10.9 Pipe body - Full-length wall-loss inspection
10.10 Pipe body - Ultrasonic inspection of the
critical area
10.11 Pipe body - Calculation of cross-sectional area
10.12 Pipe body - Document review (traceability)
10.13 Pipe body - Evaluation and classification
10.14 Tool joints
10.15 Tool joints - Check for box swell and pin
stretch
10.16 Repair of rejected tool joints
10.17 Tool joints - Check tool-joint pin and box
outside diameter and eccentric wear
10.18 Tool joints - Measure tool-joint pin and box
outside diameter and check for eccentric wear
10.19 Tool joints - Check tool-joint pin and box tong
space
10.20 Tool joints - Measure tool-joint pin and box
tong space
10.21 Tool joint - Magnetic-particle inspection of
the pin threads
10.22 Tool joint - Magnetic-particle inspection of
box threads
10.23 Tool joints - Measure tool-joint pin inside
diameter
10.24 Magnetic-particle inspection of the connection
OD for heat-check cracking
10.25 Bi-directional wet magnetic-particle inspection
of the connection OD for heat-check cracking
10.26 Tool joints - Measure the tool-joint counterbore
depth, pin-base length and seal width
10.27 BHA connection - Visual inspection of bevels,
seals, threads and stress-relief features
10.28 BHA - Measure box outside diameter, pin inside
diameter, counterbore diameter and benchmark
location if a benchmark is present
10.29 BHA - Check bevel diameter
10.30 BHA - Measure bevel diameter
10.31 BHA - Magnetic-particle inspection of the pin
and box threads
10.32 BHA connection - Liquid-penetrant inspection
of the pin and box threads
10.33 BHA - Dimensional measurement of stress-relief
features
10.34 Length measurements of the counterbore, pin
and pin neck
10.35 Drill collar - Visual full-length OD and ID,
markings, fish-neck length and tong space
10.36 Drill-collar elevator groove and slip-recess
magnetic-particle inspection
10.37 Drill-collar elevator-groove and slip-recess
measurement
10.38 Subs (full-length visual OD and ID), fish-neck
length, section-change radius and markings
10.39 Float-bore recess measurements
10.40 Magnetic-particle inspection of
subs - Full-length, internal and external
10.41 HWDP - Visual full-length OD and ID, markings
and tong space
10.42 Visual inspection and wear pattern report
for kelly
10.43 Magnetic-particle evaluation of critical
areas on kellys
10.44 Magnetic-particle evaluation, full length,
of the drive section on kellys
10.45 Stabilizer (full-length visual OD and ID),
fish-neck length, blade condition, ring
gauge and markings
10.46 Magnetic-particle inspection of the base
of stabilizer blades for cracking
10.47 Function test
10.48 Bi-directional, wet magnetic-particle
inspection of the base of stabilizer blade
for cracking
10.49 Visual inspection of jars (drilling and
fishing), accelerators and shock subs
10.50 Maintenance review
10.51 Dimensional measurement of wear areas as
specified by OEM requirements
10.52 Original equipment manufacturer designated
testing for used equipment
10.53 MWD/LWD - Visual, full-length OD and ID, and
markings, including visual inspection of
hard-banding and coatings
10.54 Motors and turbines - Visual, full-length OD
and ID and markings, including visual inspection
of hard-banding and coatings
10.55 Reamers, scrapers, and hole openers - Visual,
full-length OD and ID and markings, including
visual inspection of hard-banding and coatings
10.56 Rotary steerable - Visual, full-length OD and ID
and markings, including visual inspection of
hard-banding
10.57 Full-length drift
10.58 Proprietary equipment inspection
10.59 Hard-banding inspection
10.60 Transverse magnetic-particle inspection of
tool-joint OD and ID under the pin threads
10.61 Drill-pipe body - Internal magnetic-particle
inspection of the critical area
10.62 Drill-pipe body - Bi-directional, internal
magnetic-particle inspection of the critical
area
10.63 API external upset-thread connection inspection
Annex A (normative) - Original equipment manufacturer
(OEM) requirements
Annex B (normative) - Required and additional inspections
by product and class of service
Annex C (normative) - SI units
Annex D (informative) - USC units
Annex E (informative) - Inspection-level guidelines
Annex F (informative) - Proprietary drill stem connection
inspection
Annex G (informative) - Used work-string tubing
proprietary-connection thread inspection
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.