SAE AMS 2470 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ANODIC TREATMENT OF ALUMINUM ALLOYS, CHROMIC ACID PROCESS
Hardcopy , PDF
20-05-2019
English
01-01-2013
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. ACKNOWLEDGMENT
7. REJECTIONS
8. NOTES
Specifies the requirements for anodic coatings on aluminum alloys.
Committee |
AMS-B
|
DocumentType |
Standard
|
Pages |
8
|
PublisherName |
SAE International
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
ASTM D 3762 : 2003 : R2010 | Similar to |
ASTM D 3023 : 1998 : R2011 | Similar to |
ASTM D 3762 : 2003 | Similar to |
ASTM D 3023 : 1998 : R2003 | Similar to |
MIL A 8625 : F | Similar to |
MIL-PRF-680 Revision C:2010 | DEGREASING SOLVENT |
MIL-PRF-32359 Base Document:2012 | CLEANER, GENERAL, FOR GROUND VEHICLES AND GROUND SUPPORT EQUIPMENT, HAP-FREE |
MS123142 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 2 3/8 INCH, ALUMINUM |
MS123122 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 3/8 INCH, ALUMINUM |
MS123133 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 5/16 INCH, ALUMINUM |
MS9095 Revision B:2010 | NIPPLE, TUBE - ALUMINUM, BOSS |
SAE AMS 1428 : 2017 | FLUID, AIRCRAFT DEICING/ANTI-ICING, NON-NEWTONIAN, (PSEUDOPLASTIC), SAE TYPES 2, 3 AND 4 |
SAE AMS 1551 : 2008 | CLEANER, TURBINE ENGINE GAS PATH AQUEOUS TYPE |
ASTM D 2651 : 2001 : R2008 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
SAE AMS 4254 : 2017 | ALUMINUM ALLOY, ARAMID FIBER REINFORCED, LAMINATED SHEET, 4.4CU - 1.5MG - 0.6MN (2024-T3), 3, 5, 7, OR 9 PLY |
MS123138 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 7/8 INCH, ALUMINUM |
MS123130 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 1/16 INCH, ALUMINUM |
MIL-STD-1516 Revision B:1990 | UNIFIED CODE FOR COATINGS AND FINISHES FOR DOD MATERIAL |
MIL-PRF-5806 Revision H:2002 | BOX, SHIPPING AND STORAGE, HELICOPTER BLADE |
MIL-DTL-9479 Revision E:1999 | |
SAE AMS1550B:1995(R2012) | CLEANER, WATER BASE, AIRCRAFT INTERIOR HARD SURFACE MATERIALS |
SAE AMS 2503 : 2017 | BLACK FINISHING - LOW BAKING ENAMEL |
SAE AMS 2472 : 2014 | ANODIC TREATMENT OF ALUMINUM ALLOYS, SULFURIC ACID PROCESS, DYED COATING |
SAE AS 7222 : 2013 | ALUMINUM RIVETS, UNS A92117 2.5Cu - 0.3Mg (2117-T4) - PROCUREMENT SPECIFICATION |
SAE AMS 1453 : 2015 | DISINFECTANT CLEANER FOR AIRCRAFT INTERIOR GENERAL PURPOSE LIQUID |
SAE AMS 1431 : 2012 | COMPOUND, SOLID RUNWAY AND TAXIWAY DEICING/ANTI-ICING |
DWA-M 143-20:2018 | TEST METHOD FOR DROP IMPACT RESISTANCE OF BLOW-MOLDED THERMOPLASTIC CONTAINERS |
SAE AMS 4258 : 2017 | LAMINATED SHEET, ALUMINUM ALLOY, ARAMID FIBER REINFORCED, 5.7ZN - 2.2MG - 1.6CU - 0.22CR (ALCLAD, ONE SIDE 7475-T761), 5 OR 7 PLY |
BS M 75:1994 | Aircraft de-icing/anti-icing Newtonian fluids, ISO type I |
MS123134 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 3/8 INCH, ALUMINUM |
MS123139 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 2 INCH, ALUMINUM |
MS123136 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 5/8 INCH, ALUMINUM |
MS123129 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 INCH, ALUMINUM |
MS123140 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 2 1/8 INCH, ALUMINUM |
MS123132 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 1/4 INCH, ALUMINUM |
SAE J 24714 : 2001 | Fluid Systems—Connector Tubes—General Specification and Part Standard |
SAE AMS 1375 : 2012 | REMOVER, PAINT, EPOXY AND POLYURETHANE PAINT SYSTEMS |
SAE AMS 1526 : 2008 | CLEANER FOR AIRCRAFT EXTERIOR SURFACES, WATER-MISCIBLE, PRESSURE-SPRAYING TYPE |
SAE AMS 2510 : 2017 | ENGINE GRAY FINISHING LOW BAKING |
SAE AMS 1377 : 2012 | REMOVER, PAINT, EPOXY AND POLYURETHANE PAINT SYSTEM, NON-CHLORINATED SOLVENT |
MS123135 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 1/2 INCH, ALUMINUM |
BS M 78:1995 | Aircraft de-icing/anti-icing non-Newtonian fluids, ISO type II |
MS123127 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 3/4 INCH, ALUMINUM |
MS123141 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 2 1/4 INCH, ALUMINUM |
MS123143 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 2 1/2 INCH, ALUMINUM |
MS123121 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 5/16 INCH, ALUMINUM |
MS123120 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1/4 INCH, ALUMINUM |
SAE AMS 1376 : 1998 | REMOVER, EPOXY PAINT, ACID TYPE, THICKENED |
SAE AMS 4302 : 2017 | ALUMINUM ALLOY, LAMINATED, SHEET, ARAMID FIBER REINFORCED, 5.7ZN - 2.2MG - 1.6CU - 0.22CR (7475-T761), 3, 5, 7, OR 9 PLY |
MIL C 29602 : 0 | CLEANING COMPOUNDS, FOR PARTS WASHERS AND SPRAY CABINETS |
SAE ARP 1755 : 2000 | EFFECT OF CLEANING AGENTS ON AIRCRAFT ENGINE MATERIALS, STOCK LOSS TEST METHOD |
SAE AMS 1536 : 2008 | CLEANER FOR AIRCRAFT COMPONENTS COLD TANK TYPE, SOLVENT-BASE |
SAE AMS 1432 : 1995 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS, POTASSIUM ACETATE BASE |
SAE AMS 3167 : 2005 | SOLVENTS, WIPE FOR CLEANING PRIOR TO APPLICATION OF PRIMER AND TOP COAT MATERIALS, OR SEALING COMPOUNDS |
MS123123 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 7/16 INCH, ALUMINUM |
MS123128 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 7/8 INCH, ALUMINUM |
MS123137 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 3/4 INCH, ALUMINUM |
MS123126 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 5/8 INCH, ALUMINUM |
MS123131 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1 1/8 INCH, ALUMINUM |
SAE AMS 1426 : 2016 | FLUID, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS GLYCOL BASE |
SAE AMS 1659 : 1991 | COATING, SOIL BARRIER, SEMI-PERMANENT |
SAE AMS 1527 : 2014 | CLEANER FOR AIRCRAFT EXTERIOR SURFACES, WATER-MISCIBLE, FOAM-ON, PRESSURE-SPRAYING |
SAE AMS 1424 : 2017 | FLUID, AIRCRAFT DEICING/ANTI-ICING, SAE TYPE 1 |
MIL-DTL-55302-78 Revision D:2004 | Connectors, Printed Circuit Subassembly and Accessories: Key, Polarizing, Connectors, Electrical Printed Wiring Boards |
MS123125 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 9/16 INCH, ALUMINUM |
SAE AMS 1540 : 2015 | CLEANER, THRUST REVERSER, WATER-BASE |
MS123124 Revision D:2010 | PLUG - STRAIGHT THREAD, O-RING SEAL, 1/2 INCH, ALUMINUM |
SAE AMS 1435 : 2012 | FLUID, GENERIC, DEICING/ANTI-ICING, RUNWAYS AND TAXIWAYS |
SAE AMS 1388 : 2008 | REMOVER, TEMPORARY COATING, ALKALINE TYPE, WATER BASE |
ASTM D 2651 : 2001 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
SAE AS 838 : 2013 | AIRCRAFT HYDRAULIC STARTER/PUMPS |
ASTM D 2651 : 2001 : R2016 | Standard Guide for Preparation of Metal Surfaces for Adhesive Bonding |
SAE AMS 2473 : 2013 | CHEMICAL FILM TREATMENT FOR ALUMINUM ALLOYS, GENERAL PURPOSE COATING |
SAE AMS 4037 : 2014 | ALUMINUM ALLOY, SHEET AND PLATE, 4.4CU - 1.5MG - 0.60MN (2024; -T3 FLAT SHEET, -T351 PLATE) SOLUTION HEAT TREATED |
SAE AMS 2472 : 2014 | ANODIC TREATMENT OF ALUMINUM ALLOYS, SULFURIC ACID PROCESS, DYED COATING |
SAE AMS 2471 : 2014 | ANODIC TREATMENT OF ALUMINUM ALLOYS SULFURIC ACID PROCESS, UNDYED COATING |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.