SAE AS 604 : 2012
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, METALLIC REINFORCED, 3000 PSI, 400 DEGREES F, HEAVYWEIGHT, HYDRAULIC
Available format(s)
Hardcopy , PDF
Superseded date
30-06-2022
Language(s)
English
Published date
21-11-2012
Publisher
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALITY ASSURANCE PROVISIONS
5. PREPARATION FOR DELIVERY
6. NOTES
This Aerospace Standard (AS) defines the requirements for a heavy braid polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high temperature, 400 °F, high pressure, 3000 psi, aircraft hydraulic fluid systems, also for use in pneumatic systems which allow some gaseous diffusion through the PTFE wall.
| Committee |
G-3
|
| DocumentType |
Revision
|
| Pages |
24
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE AIR 4092 : 2013 | INVESTIGATION OF PTFE 'MELT' PHENOMENON FOR HIGH PRESSURE HOSES |
| MIL-DTL-32093 Revision A:2005 | INITIATOR, CARTRIDGE ACTUATED JAU-75/A, JAU-76/A, JAU-77/A |
| SAE AIR 5693 : 2014 | COMPATIBILITY OF PTFE HOSE ASSEMBLIES WITH TYPICAL FLUIDS FOUND IN AEROSPACE APPLICATIONS |
| A-A-59469 Base Document:1999 | Washer-Extractor, Laundry, 35 to 200 Pound Capacity (Naval Shipboard) |
| MIL-DTL-5513 Revision D:2012 | SWIVEL JOINT, HYDRAULIC |
| MIL-H-5440 Revision H:1993 | HYDRAULIC SYSTEMS, AIRCRAFT, TYPES 1 AND 11 DESIGN AND INSTALLATION REQUIREMENTS FOR |
| SAE AS 1896 : 2013 | COUPLING ASSEMBLY, SELF-SEALING, ONE SIDE ONLY, HYDRAULIC |
| A-A-59471 Base Document:1999 | Dry Cleaning Presses and Finishing Equipment (Naval Shipboard) |
| SAE ARP 4752 : 2013 | AEROSPACE - DESIGN AND INSTALLATION OF COMMERCIAL TRANSPORT AIRCRAFT HYDRAULIC SYSTEMS |
| SAE AIR 4543 : 2017 | AEROSPACE HYDRAULICS AND ACTUATION LESSONS LEARNED |
| SAE AS 150 : 2017 | HOSE ASSEMBLY, TYPE CLASSIFICATIONS OF, BASIC PERFORMANCE AND FIRE RESISTANCE |
| SAE AMS 5689 : 2012 | STEEL, CORROSION AND HEAT RESISTANT, WIRE 18CR - 10.5NI - 0.40TI (321) SOLUTION HEAT TREATED |
| SAE AMS5659S : 2016 | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu<br> |
| SAE AMS 5645 : 2016 | STEEL, CORROSION AND HEAT RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 18CR - 10NI - 0.40TI (321), SOLUTION HEAT TREATED |
| SAE ARP 1835 : 2013 | PREPARATION FOR DELIVERY, GENERAL REQUIREMENTS FOR HOSE ASSEMBLIES |
| SAE AS 611F : 2010 | HOSE ASSEMBLY AND TUBING, POLYTETRAFLUOROETHYLENE, CLEANING METHODS FOR |
| ASTM A 262 : 2015 : REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| SAE AMS 5581 : 2010 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, SEAMLESS OR WELDED TUBING, 62NI - 21.5CR - 9.0MO - 3.7CB (NB), ANNEALED |
| NAS1760:2015 | FITTING END, FLARELESS ACORN, STANDARD DIMENSIONS FOR |
| MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| SAE AMS 5571J:2012(R2018) | STEEL, CORROSION AND HEAT-RESISTANT, SEAMLESS TUBING, 18CR - 10.5NI - 0.70CB (NB) (347), SOLUTION HEAT TREATED |
| SAE AMS 5643 : 2016 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 16CR - 4.0NI - 0.30CB (NB) - 4.0CU, SOLUTION HEAT TREATED, PRECIPITATION HARDENABLE |
| SAE AS 4395 : 2013 | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
| SAE AMS 5743 : 2014 | STEEL, CORROSION AND HEAT-RESISTANT, BARS AND FORGINGS 15.5CR - 4.5NI - 2.9MO - 0.10N SOLUTION HEAT TREATED, SUB-ZERO COOLED, EQUALIZED, AND OVER-TEMPERED |
| SAE AMS 5697 : 2012 | STEEL, CORROSION-RESISTANT, WIRE, 19CR - 9.5NI (304), SOLUTION HEAT TREATED |
| SAE AMS 5690 : 2015 | STEEL, CORROSION AND HEAT RESISTANT, WIRE, 17CR - 12NI - 2.5MO (316), SOLUTION HEAT TREATED |
| SAE AMS 5573 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, SEAMLESS TUBING, 17CR - 12NI - 2.5MO (SAE 30316), SOLUTION HEAT TREATED |
| SAE AMS 5561 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, WELDED AND DRAWN OR SEAMLESS AND DRAWN TUBING, 9.0MN - 20CR - 6.5NI - 0.28N, HIGH-PRESSURE HYDRAULIC |
| SAE AS 1055 : 2013 | FIRE TESTING OF FLEXIBLE HOSE, TUBE ASSEMBLIES, COILS, FITTINGS AND SIMILAR SYSTEM COMPONENTS |
| MIL-HDBK-831 Revision A:2013 | PREPARATION OF TEST REPORTS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS 85421/1 : 2002 | FITTING END, STANDARD DIMENSIONS FOR DYNAMIC BEAM SEAL, MALE |
| SAE AMS 5647 : 2017 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 19CR - 9.5NI, SOLUTION HEAT TREATED |
| SAE AMS 5648 : 2016 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 17CR - 12NI - 2.5MO (316), SOLUTION HEAT TREATED |
| MIL-PRF-680 Revision C:2010 | DEGREASING SOLVENT |
| SAE ARP 908 : 2013 | TORQUE REQUIREMENTS, INSTALLATION AND QUALIFICATION TEST, HOSE AND TUBE FITTING |
| SAE AMS QQ P 35 : 1998 | PASSIVATION TREATMENTS FOR CORROSION-RESISTANT STEEL |
| MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
| SAE AS 7003 : 2008 | NADCAP PROGRAM REQUIREMENTS |
| ASME Y14.24 : 2012 | TYPES AND APPLICATIONS OF ENGINEERING DRAWINGS - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
| SAE AS 7112 : 1997 | NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM REQUIREMENTS FOR FLUID SYSTEM COMPONENTS |
| SAE AMS 5567 : 2015 | STEEL, CORROSION RESISTANT, SEAMLESS OR WELDED HYDRAULIC TUBING, 19CR - 10NI (304), SOLUTION HEAT TREATED |
| SAE AMS 5646 : 2014 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 18CR - 11NI - 0.60CB(NB) (347), SOLUTION HEAT TREATED |
| SAE AS 85421 : 2015 | FITTINGS, TUBE, FLUID SYSTEMS, SEPARABLE, BEAM SEAL, 3000/4000 PSI, GENERAL SPECIFICATION FOR |
| SAE AMS QQ S 763D : 2013(S2015) | STEEL, CORROSION RESISTANT, BARS, WIRE, SHAPES, AND FORGINGS |
| SAE AMS 5688 : 2012 | STEEL, CORROSION-RESISTANT, WIRE, 18CR - 9.0NI (SAE 30302), SPRING TEMPER |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| SAE AS 1072F : 2013(S2019) | SLEEVE, HOSE ASSEMBLY, FIRE PROTECTION |
| SAE AMS 5575 : 2013 | STEEL, CORROSION AND HEAT-RESISTANT, WELDED TUBING, 18CR - 10.5NI - 0.70CB (NB) (347), SOLUTION HEAT TREATED |
| SAE AMS 5570 : 2013 | STEEL, CORROSION AND HEAT-RESISTANT, SEAMLESS TUBING 18CR - 11NI - 0.40TI (321), SOLUTION HEAT TREATED |
| SAE AS 2078 : 2015 | TEST METHODS, HOSE ASSEMBLIES, POLYTETRAFLUOROETHYLENE (PTFE) |
| MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
| SAE AMS 5639 : 2017 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 19CR - 10NI, SOLUTION HEAT TREATED |
| MIL H 5606 : G | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE |
| SAE AS 33514 : 2015 | FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL |
| SAE AS 4375 : 2013 | FITTING END, FLARELESS, DESIGN STANDARD |
| SAE AS 150 : 2014 | HOSE ASSEMBLY, TYPE CLASSIFICATIONS OF, BASIC PERFORMANCE AND FIRE RESISTANCE |
| SAE AMS5644E:1964(S2017) | STEEL, BARS AND FORGINGS, CORROSION RESISTANT, 17CR - 7NI - 1AL |
| ASME Y14.100 : 2017 | ENGINEERING DRAWING PRACTICES - ENGINEERING DRAWING AND RELATED DOCUMENTATION PRACTICES |
| SAE AMS 5653 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 17CR - 12NI - 2.5MO (0.030 MAX C) (316L), SOLUTION HEAT TREATED |
| SAE AMS 5666H : 2016 | NICKEL ALLOY, CORROSION AND HEAT-RESISTANT, BARS, FORGINGS, EXTRUSIONS, AND RINGS, 62NI - 21.5CR - 9.0MO - 3.65CB (NB), ANNEALED |
| SAE AMS 5556 : 2016 | STEEL, CORROSION AND HEAT-RESISTANT, SEAMLESS OR WELDED HYDRAULIC TUBING 18CR - 11NI - 0.70CB (347) SOLUTION HEAT TREATED |
| NAS847:2012 | CAPS AND PLUGS, PROTECTIVE, DUST AND MOISTURE SEAL |
| SAE AMS 5557 : 2012 | STEEL, CORROSION AND HEAT RESISTANT, SEAMLESS OR WELDED HYDRAULIC TUBING, 18.5CR - 10.5NI - 0.40TI (SAE 30321), SOLUTION HEAT TREATED |
Important note : All end users must be registered with an Account prior to user licenses being assigned.Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.