Battery Storage Safety Standards for Solar and EV Charging Installations
Battery storage safety standards support how battery cabinets, rooftop arrays and wall-mounted chargers are installed, and one job can call on AS/NZS, IEC, UL and NFPA documents at once.
Additionally, electrification is a key theme at COP31 in Antalya, where the Presidency has proposed a voluntary global goal for electricity to meet 35% of final energy demand by 2035. Türkiye holds the presidency in this summit while Australia leads the negotiations.
This guide maps each part of the job to its standard, so you know which document to open on site.
|
Key Takeaways
|
The Importance of Battery Storage Safety Standards at Installation Level
Installation standards centre on what happens once equipment reaches a site, like how a PV array is isolated and how a charger is supplied. AS/NZS 5139:2019 covers battery energy storage systems (BESS). It's the starting point for BESS installation safety in Australia and New Zealand. Meanwhile, AS/NZS 5033:2021 covers PV array wiring, protection, switching and earthing. AS/NZS 3000:2018 covers EV socket outlets and charging stations in Appendix P.
Several of these documents have changed recently. Amendment 1 to AS/NZS 5139:2019 was published on 19 December 2025, and the Western Australian Government points to clearer definitions in Clause 1.3. Internationally, IEC 62933-5-2 reached its second edition in December 2025, and NFPA 855:2026, published in September 2025, is the current edition.
Dates of effect for the AS/NZS 5139 amendment differ between states and territories.
What Changed in AS/NZS 5139 Amendment 1
Amendment 1 to AS/NZS 5139:2019 was published on 19 December 2025. It updates clauses across the standard, including the terms and definitions in Clause 1.3 and the arc flash requirements in Clause 7.11, and adds a new informative Appendix I on calculating cell short-circuit current. Dates of effect vary: Western Australia requires full compliance from 19 June 2026, so check your own state or territory regulator.
Battery Storage Safety Standards You Need to Know
Battery safety comes in layers, and each standard covers one of them.
Cells and Batteries: IEC 62619:2022
IEC 62619:2022 sets the requirements and tests for the safe operation of secondary lithium cells and batteries in industrial applications, including stationary ones. The second edition was published on 24 May 2022 and replaces the 2017 edition. It deals with first-life cells and batteries, so reused or second-life units are not covered. Australia's national adoption is AS IEC 62619:2023.
BESS Installation Safety: AS/NZS 5139:2019 and IEC 62933-5-2:2025
For battery energy storage systems connected to power conversion equipment, AS/NZS 5139 sets the installation and safety requirements in Australia and New Zealand. At the international level, IEC 62933-5-2:2025, the second edition published in December 2025, covers safety for people and their surroundings wherever a grid-connected storage system includes an electrochemical subsystem. It adds to the general safety considerations in Part 5-1 of the IEC 62933 series.
North American Standards: NFPA 855 and UL 9540
UL 9540 is a safety standard for stationary energy storage systems and equipment, indoor and outdoor, residential and non-residential. UL Standards & Engagement published its third edition, UL 9540:3ED 2023-06-28, on 28 June 2023. NFPA 855:2026 applies to the design, construction, installation, commissioning, operation, maintenance and decommissioning of stationary energy storage systems. If your project has a North American footprint, expect to see both NFPA 855 and UL 9540 in the same specification.
Solar PV and EV Charging Standards That Sit Beside Your Batteries
Batteries seldom turn up on their own. More often an array feeds them, a charger draws from them, and a switchboard has to tie everything together.
Solar PV Installation Standards: AS/NZS 5033:2021
Among the solar PV installation standards used in Australia, AS/NZS 5033:2021 sets general installation and safety requirements for PV arrays, covering DC array wiring, protection devices, switching and earthing. Standards Australia published it on 19 November 2021 to replace the 2014 edition. Our solar standards guide goes deeper on the array side.
EV Charger Installation Standards: IEC 61851-1 and AS/NZS 3000
For EV charger installation standards, start with IEC 61851-1:2017 for the equipment. It sets general requirements for EV supply equipment rated up to 1,000 V AC or 1,500 V DC. A corrigendum followed in 2023. It leaves bidirectional energy transfer out, so if your project involves vehicle-to-home or vehicle-to-grid use, check which additional standards your network service provider and regulator require for bidirectional chargers. Meanwhile, AS/NZS 3000:2018 deals with wiring. It includes Appendix P, with guidance on EV socket outlets and charging stations, plus Appendix Q on DC circuit protection. Our Wiring Rules guide walks through how the standard is laid out.
Common Challenges With Battery Storage, Solar and EV Charger Standards
Two errors come up often: working from a superseded edition, and treating an international standard as if it were the national adoption. When one job draws on several standards, it’s easy to get confused about which to apply. Here are some other mix-ups to look out for.
- Product and installation scope. IEC 62619:2022 covers first-life cells and batteries. It does not cover second-life units or how a system is installed. For BESS installation in Australia and New Zealand, use AS/NZS 5139:2019 and Amendment 1.
- Charger scope. IEC 61851-1:2017 leaves bidirectional energy transfers out, so vehicle-to-home projects need a different document.
- North American references. If a supplier or specification cites NFPA 855 or UL 9540, check whether your regulator references them. In Australia and New Zealand, AS/NZS 5139 remains the installation reference.
A Checklist for Your Battery, Solar and EV Charging Projects
A short list at the start of a job keeps the right standards in view. Here's one you can adapt to your own process.
- List the equipment you are installing (a battery, an array, a charger or a mix) and pair each item with its respective standard.
- Check which edition your state or territory regulator references, and when AS/NZS 5139 Amendment 1 takes effect where you work.
- Ask your supplier whether the battery product has been tested to IEC 62619.
- Read the location, clearance and barrier clauses in AS/NZS 5139:2019 and Amendment 1 before the site visit. Reading them afterwards is a lot more expensive.
- Work through isolation, cable routing and earthing for the array using AS/NZS 5033:2021 alongside AS/NZS 3000:2018.
- Keep verification records. AS/NZS 3000:2018 covers them in Section 8, and AS/NZS 3017:2022 covers inspection and testing.
- Set up alerts for new editions of the standards you use with StandardsWatch.
Bringing Battery Storage Safety Standards Together on Site
Battery, solar and EV charging standards each cover a different part of the job. Start by matching every item on site to its standard.
For batteries, IEC 62619 covers the cells, while AS/NZS 5139:2019 and IEC 62933-5-2 address BESS installation safety. NFPA 855 and UL 9540 apply to North American projects. AS/NZS 5033 covers the PV array, IEC 61851-1 covers the charger, and AS/NZS 3000 ties the wiring together. Applying these standards and working in the current edition can help support compliance and safer installations.
Common Questions About Battery Storage Safety Standards
AS/NZS 5139:2019 sets installation and safety requirements for battery energy storage systems (BESS) connected to power conversion equipment. It was reissued incorporating Amendment 1 in December 2025. Each state and territory regulator decides which edition applies, so check with yours before you start work.
Amendment 1, published on 19 December 2025, updates clauses including the definitions in Clause 1.3 and the arc flash requirements in Clause 7.11, and adds an informative appendix on calculating cell short-circuit current.
AS/NZS 5033:2021 sets general installation and safety requirements for PV arrays, including DC array wiring, protection devices, switching and earthing. Standards Australia published it on 19 November 2021 to replace the 2014 edition. AS/NZS 3000 references this standard, so installers often work to both together.
UL 9540 is a safety standard for energy storage systems and equipment. NFPA 855 covers the installation of stationary energy storage systems over their life. Both standards are North American documents, and projects in that region can draw on both.
IEC 61851-1:2017 covers EV supply equipment for charging electric road vehicles with a rated supply voltage up to 1,000 V AC or 1,500 V DC. In Australia and New Zealand, AS/NZS 3000:2018 also gives guidance on EV socket outlets and charging stations in Appendix P.