00/121221 DC : DRAFT MARCH 2000
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ISO/CE 1133 - PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS
23-11-2012
11-10-2005
Foreword
1 Scope
2 Normative references
3 Apparatus
3.1 Basis Apparatus
3.2 Accessory Equipment
4 Test Sample
5 Temperature Calibration, cleaning and maintenance
of the apparatus
5.1 Calibration of the temperature-control system
5.2 Cleaning the apparatus
6 Procedure A
7 Procedure B
7.1 Principle
7.2 Optimum measurement accuracy
7.3 Pre-treatment
7.4 Determination
7.5 Expression of results
8 Flow rate ratio (FRR)
9 Precision
10 Test report
Annex A (informative) Test conditions for melt flow
rate determination
Annex B (informative) Conditions in use for the
designation of standards for thermoplastic
materials
Draft: ISO/CD 1133
| Committee |
PRI/21
|
| DocumentType |
Draft
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 6507-1:2005 | Metallic materials — Vickers hardness test — Part 1: Test method |
| ISO 1622-1:2012 | Plastics — Polystyrene (PS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 1628-1:2009 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 1: General principles |
| ISO 6402-1:2002 | Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 1873-2:2007 | Plastics — Polypropylene (PP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties |
| ISO 4613-1:1993 | Plastics — Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials — Part 1: Designation and specification |
| ISO 2897-1:1997 | Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 4894-1:1997 | Plastics — Styrene/acrylonitrile (SAN) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 9988-1:2004 | Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 8257-1:1998 | Plastics — Poly(methyl methacrylate) (PMMA) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 468:1982 | Surface roughness — Parameters, their values and general rules for specifying requirements |
| ISO 7391-1:2006 | Plastics — Polycarbonate (PC) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 1872-1:1993 | Plastics — Polyethylene (PE) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 2580-1:2002 | Plastics — Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |
| ISO 10366-1:2002 | Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications |