05/30132920 DC : DRAFT APR 2005
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR THE EXECUTION OF STEEL STRUCTURES
Published date
23-11-2012
Publisher
Superseded date
31-12-2008
Superseded by
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Definitions
4 Specifications and documentation
5 Constituent products
6 Fabrication
7 Welding
8 Mechanical fastening
9 Erection
10 Surface treatment
11 Geometrical tolerances
12 Inspection, testing and correction
Annex A 1 (normative) List of required additional information
Annex A 2 (normative) List of options to be specified
Annex A 3 (normative) Requirements related to the execution classes
Annex B (informative) Guidance for the choice of execution classes
Annex C (informative) Typical format for a quality plan
C.1 Scope
C.2 Management
C.3 Specification review
C.4 Documentation
C.5 Inspection and testing procedures
Annex D (informative) Selection and use of mechanical
fasteners for sheeting
D.1 Scope
D.2 Selection of fastener type
D.3 Use of Special fasteners
Annex E (informative) Welded joints in hollow sections
E.1 Guidance for start and stop positions
E.2 Preparation of joint faces
E.3 Assembly for welding
Annex F (informative) Welding methods for thin gauge steel
components
F.1 Intermittent welding
F.2 Lap joints
F.3 Butt welds
Annex G (normative) Procedure test for determination of
slip factor
G.1 The purpose of testing
G.2 Significant variables
G.3 Test specimens
G.4 Test procedure
G.5 Extended creep test
G.6 Test results
Annex H (normative) Use of compressible washer-type direct
tension indicators
H.1 Fitting
H.2 Checking
Annex J (informative) Hexagon injection bolts
J.1 General
J.2 Hole sizes
J.3 Bolts
J.4 Washers
J.5 Nuts
J.6 Resin
J.7 Tightening
J.8 Installation
Annex K (normative) Corrosion protection
K.1 General
K.2 Surface preparation for carbon steels
K.3 Welds and surfaces for welding
K.4 Surfaces in non-friction-grip preloaded connections
K.5 Preparation of fasteners
K.6 Coating methods
Annex L 1 Geometrical tolerances - Essential
tolerances (normative)
Annex L 2 Geometrical tolerances - Supplementary
tolerances (informative)
Annex M (normative) Sequential method for bolt
tightening inspection
M.1 General
M.2 Application
Bibliography
EN 1090-2
| Committee |
B/521
|
| DocumentType |
Draft
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 1090-2 : DRAFT 2015 | Identical |
| EN 12073 : 1999 | WELDING CONSUMABLES - TUBULAR CORED ELECTRODES FOR METAL ARC WELDING WITH OR WITHOUT A GAS SHIELD OF STAINLESS AND HEAT-RESISTING STEELS - CLASSIFICATION |
| EN 10162:2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances |
| PREN 14399-2 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 2: SUITABILITY TEST FOR PRELOADING |
| PREN 15048-2 : DRAFT 2014 | NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 2: FITNESS FOR PURPOSE |
| EN ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012) |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| ISO 1479:2011 | Hexagon head tapping screws |
| EN 439 : 1994 | WELDING CONSUMABLES - SHIELDING GASES FOR ARC WELDING AND CUTTING |
| EN ISO 6789:2003 | Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003) |
| EN ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012) |
| EN 440 : 1994 | WELDING CONSUMABLES - WIRE ELECTRODES AND DEPOSITS FOR GAS SHIELDED METAL ARC WELDING OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION |
| EN 10140:2006 | Cold rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 10079:2007 | Definition of steel products |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| EN 10149-1:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| PREN 14399-5 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| EN 756:2004 | Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012) |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head - St/St (ISO 15979:2002) |
| PREN 13479 : DRAFT 2014 | WELDING CONSUMABLES - GENERAL PRODUCT STANDARD FOR FILLER METALS AND FLUXES FOR FUSION WELDING OF METALLIC MATERIALS |
| ISO 10509:2012 | Hexagon flange head tapping screws |
| EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| EN ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012) |
| ISO 7049:2011 | Cross-recessed pan head tapping screws |
| EN 12535 : 2000 | WELDING CONSUMABLES - TUBULAR CORED ELECTRODES FOR GAS SHIELDED METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION |
| EN ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protrudiing head - St/St (ISO 15976:2002) |
| PREN 14399-4 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN 10131:2006 | Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EURONORM 60 : 1977 | HOT-ROLLED ROUND STEEL FOR GENERAL USE |
| EN 10327:2004 | Continuously hot-dip coated strip and sheet of low carbon steels for cold forming - Technical delivery conditions |
| EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
| EN ISO 1127:1996 | Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) |
| EN 10326:2004 | Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| EN 10272:2016 | Stainless steel bars for pressure purposes |
| EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| ISO 1481:2011 | Slotted pan head tapping screws |
| EN 10143:2006 | Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape |
| EURONORM 65 : 1980 | HOT-ROLLED ROUND STEEL FOR SCREWS AND RIVETS |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EURONORM 61 : 1982 | HOT-ROLLED HEXAGON STEEL |
| EURONORM 58 : 1978 | HOT-ROLLED FLAT STEEL FOR GENERAL USE |
| EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
| PREN 14399-3 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| EN ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012) |
| EN 10025-5:2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| EN 12072 : 1999 | WELDING CONSUMABLES - WIRE ELECTRODES, WIRES AND RODS FOR ARC WELDING OF STAINLESS AND HEAT-RESISTING STEELS - CLASSIFICATION |
| EN 760:1996 | Welding consumables - Fluxes for submerged arc welding - Classification |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 4997:2015 | Cold-reduced carbon steel sheet of structural quality |
| EN 1600:1997 | Welding consumables - Covered electrodes for manual arc welding of stainless and heat resisting steels - Classification |
| EN 499 : 1994 | WELDING CONSUMABLES - COVERED ELECTRODES FOR MANUAL METAL ARC OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| PREN 14399-8 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| EN 10020:2000 | Definition and classification of grades of steel |
| EN 10219-2:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties |
| EN 758 : 1997 | WELDING CONSUMABLES - TUBULAR COVERED ELECTRODES FOR METAL ARC WELDING WITH AND WITHOUT A GAS SHIELD OF NON ALLOY AND FINE GRAIN STEELS - CLASSIFICATION |
| EN ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO 15980:2002) |
| EN ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999) |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| EURONORM 59 : 1978 | HOT-ROLLED SQUARE STEEL FOR GENERAL USE |
| EN 10258 : 1997 | COLD-ROLLED STAINLESS STEEL AND NARROW STRIP AND CUT LENGTHS - TOLERANCES AND DIMENSIONS AND SHAPE |
| PREN 14399-7 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| PREN 10217-7 : DRAFT 2009 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 7: STAINLESS STEEL TUBES |
| PREN 14399-9 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head - A2/A2 (ISO 15984:2002) |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head - A2/A2 (ISO 15983:2002) |
| EN 10259 : 1997 | COLD-ROLLED STAINLESS STEEL WIDE STRIP AND PLATE/SHEET - TOLERANCES ON DIMENSIONS AND SHAPE |
| EN ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012) |
| EN 12534 : 1999 | WELDING CONSUMABLES - WIRE ELECTRODES, WIRES, RODS AND DEPOSITS FOR GAS SHIELDED METAL ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION |
| EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
| EN 757:1997 | Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification |
| EURONORM 17 : 1970 | WIRE ROD OF COMMON UNALLOYED STEELS FOR DRAWING; DIMENSIONS AND PERMISSIBLE DEVIATIONS |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
| PREN 14399-6 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
Summarise
Sorry this product is not available in your region.