08/30191147 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 1555-2 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES
Hardcopy , PDF
English
30-11-2010
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 Material
4.1 Compound
4.2 Compound for identification stripes
5 General characteristics
5.1 Appearance
5.2 Colour
6 Geometrical characteristics
6.1 Measurement of dimensions
6.2 Mean outside diameters, out-of-roundness (ovality) and
tolerances
6.3 Wall thicknesses and related tolerances
6.4 Circumferential reversion of pipes with a d[n] equal to
or greater than 250 mm
6.5 Coiled pipe
6.6 Lengths
7 Mechanical characteristics
7.1 Conditioning
7.2 Requirements
7.3 Retest in case of failure at 80 degree C
8 Physical characteristics
8.1 Conditioning
8.2 Requirements
9 Performance requirements
10 Marking
10.1 General
10.2 Minimum required marking
10.3 Additional marking
Annex A (normative) Pipes with co-extruded layers
A.1 General
A.2 Geometrical characteristics
A.3 Mechanical characteristics
A.4 Physical characteristics
A.5 Marking
A.6 Delamination
Annex B (normative) Pipes with peelable layer
B.1 General
B.2 Geometrical characteristics
B.3 Mechanical characteristics
B.4 Physical characteristics
B.5 Marking
B.6 Storage and installation
Annex C (normative) Squeeze-off technique
C.1 General Squeeze-off technique
C.2 Definitions
C.3 Test method
Bibliography
BS EN 1555-2
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
23
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 1555-2 : DRAFT 2008 | Identical |
| ISO 17484-1:2014 | Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| EN 12106:1997 | Plastics piping systems - Polyethylene (PE) pipes - Test method for the resistance to internal pressure after application of squeeze-off |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| EN ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477:2008) |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478:2007) |
| PREN 1555-5 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE OF THE SYSTEM |
| ISO 6259-1:2015 | Thermoplastics pipes — Determination of tensile properties — Part 1: General test method |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| EN 12007-2:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 2: Specific functional requirements for polyethylene (MOP up to and including 10 bar) |
| ISO 4065:1996 | Thermoplastics pipes — Universal wall thickness table |
| ISO 13480:1997 | Polyethylene pipes — Resistance to slow crack growth — Cone test method |
| ISO 18225:2012 | Plastics piping systems — Multilayer piping systems for outdoor gas installations — Specifications for systems |
| CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| ISO 6259-3:2015 | Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| PREN 1555-1 : DRAFT 2008 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.