10/30209612 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 1119 - GEOMETRICAL PRODUCT SPECIFICATIONS (GPS) - SERIES OF CONICAL TAPERS AND TAPER ANGLES
Hardcopy , PDF
English
31-01-2012
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 Values
Annex A (informative) - Relation to the GPS matrix
model
Bibliography
BS ISO 1119
| Committee |
TDW/4
|
| DocumentType |
Draft
|
| Pages |
17
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN ISO 1119 : DRAFT 2010 | Identical |
| ISO 8489-4:1995 | Textile machinery and accessories — Cones for cross winding — Part 4: Dimensions, tolerances and designation of cones with half angle 4 degrees 20' for winding for dyeing purposes |
| ISO/TR 14638:1995 | Geometrical product specification (GPS) — Masterplan |
| ISO 5237:1978 | Textile machinery and accessories — Cones for yarn winding (cross wound) — Half angle of the cone 5 degrees 57' |
| ISO 297:1988 | 7/24 tapers for tool shanks for manual changing |
| ISO 8489-5:1995 | Textile machinery and accessories — Cones for cross winding — Part 5: Dimensions, tolerances and designation of cones with half angle 5 degrees 57' |
| ISO 595-2:1987 | Reusable all-glass or metal-and-glass syringes for medical use — Part 2: Design, performance requirements and tests |
| ISO 5356-1:2015 | Anaesthetic and respiratory equipment — Conical connectors — Part 1: Cones and sockets |
| ISO 3:1973 | Preferred numbers — Series of preferred numbers |
| ISO 8382:1988 | Resuscitators intended for use with humans |
| ISO 3040:2016 | Geometrical product specifications (GPS) — Dimensioning and tolerancing — Cones |
| ISO 8489-3:1995 | Textile machinery and accessories — Cones for cross winding — Part 3: Dimensions, tolerances and designation of cones with half angle 4 degrees 20' |
| ISO 296:1991 | Machine tools — Self-holding tapers for tool shanks |
| ISO 595-1:1986 | Reusable all-glass or metal-and-glass syringes for medical use — Part 1: Dimensions |
| ISO 8489-2:1995 | Textile machinery and accessories — Cones for cross winding — Part 2: Dimensions, tolerances and designation of cones with half angle 3 degrees 30' |
| IEC 60095-2:2009 | Lead-acid starter batteries - Part 2: Dimensions of batteries and dimensions and marking of terminals |
| ISO 575:1978 | Textile machinery and accessories — Transfer cones — Half angle of the cone 4 degrees 20' |
| ISO 324:1978 | Textile machinery and accessories — Cones for cross winding for dyeing purposes — Half angle of the cone 4 degrees 20' |
| ISO 12164-1:2001 | Hollow taper interface with flange contact surface — Part 1: Shanks — Dimensions |
| ISO 239:1999 | Drill chuck tapers |
| ISO 368:2006 | Spinning preparatory, spinning and doubling (twisting) machinery — Tubes for ring-spinning, doubling and twisting spindles, taper 1:38 and 1:64 |
| ISO 594-1:1986 | Conical fittings with a 6 % (Luer) taper for syringes, needles and certain other medical equipment — Part 1: General requirements |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.