10/30227098 DC : 0
Current
The latest, up-to-date edition.
BS EN 16125 - LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG LIQUID PHASE AND VAPOUR PRESSURE PHASE
Hardcopy , PDF
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Design safety considerations
5 Materials
6 Design
7 Identification & corrosion protection of above ground
pipework
8 Documentation, inspection and testing
9 Maintenance
Annex A (informative) - Pipework Integrity Management
Systems (PIMS)
Annex B (normative) - Pipe sizing tables - liquid phase
Annex C (normative) - Pipe sizing tables - Gas phase
Annex D (informative) - Purging of pipework
Annex E (informative) - Environmental checklist
BS EN 16125
| Committee |
PVE/19
|
| DocumentType |
Draft
|
| Pages |
40
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Standards | Relationship |
| PREN 16125 : DRAFT 2013 | Identical |
| EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials |
| EN 15001-1:2009 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| EN 1045:1997 | Brazing - Fluxes for brazing - Classification and technical delivery conditions |
| EN 1515-1:1999 | Flanges and their joints - Bolting - Part 1: Selection of bolting |
| EN 13175:2014 | LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas (LPG) pressure vessel valves and fittings |
| EN 12007-3:2015 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 3: Specific functional requirements for steel |
| EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
| EN 10216-5:2013 | Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes |
| EN 1254-5:1998 | Copper and copper alloys - Plumbing fittings - Part 5: Fittings with short ends for capillary brazing to copper tubes |
| EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
| ISO 9454-2:1998 | Soft soldering fluxes — Classification and requirements — Part 2: Performance requirements |
| EN 1254-1:1998 | Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| EN 12007-1:2012 | Gas infrastructure - Pipelines for maximum operating pressure up to and including 16 bar - Part 1: General functional requirements |
| EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 751-2:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds |
| EN 12266-2:2012 | Industrial valves - Testing of metallic valves - Part 2: Tests, test procedures and acceptance criteria - Supplementary requirements |
| EN ISO 9454-2:2000 | Soft soldering fluxes - Classification and requirements - Part 2: Performance requirements (ISO 9454-2:1998) |
| EN 1044 : 1999 | BRAZING - FILLER METALS |
| EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000) |
| EN 12266-1:2012 | Industrial valves - Testing of metallic valves - Part 1: Pressure tests, test procedures and acceptance criteria - Mandatory requirements |
| EN 10217-7:2014 | Welded steel tubes for pressure purposes - Technical delivery conditions - Part 7: Stainless steel tubes |
| EN ISO 9453:2014 | Soft solder alloys - Chemical compositions and forms (ISO 9453:2014) |
| EN ISO 10497:2010 | Testing of valves - Fire type-testing requirements (ISO 10497:2010) |
| EN 751-1:1996 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds |
| EN 14324:2004 | Brazing - Guidance on the application of brazed joints |
| EN 10226-3:2005 | Pipes threads where pressure tight joint are made on the threads - Part 3: Verification by means of limit gauges |
| ISO 9453:2014 | Soft solder alloys — Chemical compositions and forms |
| ISO 10497:2010 | Testing of valves — Fire type-testing requirements |
| EN 10208-1:2009 | Steel pipes for pipelines for combustible fluids - Technical delivery condi-tions - Part 1: Pipes of requirement class A |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
| EN 10253-2:2007 | Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements |
| EN 10255:2004+A1:2007 | Non-Alloy steel tubes suitable for welding and threading - Technical delivery conditions |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.