11/30187339 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN ISO 12736 - PETROLEUM AND NATURAL GAS INDUSTRIES - WET THERMAL INSULATION COATINGS FOR PIPELINES, FLOW LINES, EQUIPMENT AND SUBSEA STRUCTURES
Hardcopy , PDF
English
31-01-2015
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 General requirements
6 Qualification dossier
7 Layer test requirements
8 Insulation system test requirements
9 Application process and quality control
10 Requirements for field joints
11 Handling, storage and transportation
requirements
Annex A (normative) - Hydrostatic compressive
behaviour/Tri-axial test procedures
Annex B (normative) - Simulated bend test
Annex C (normative) - Cyclic (fatigue) bend test
Annex D (normative) - Simulated tensioner test
Annex E (normative) - Simulated impact test
Annex F (normative) - Simulated thermal shock
test
Annex G (normative) - Simulated service test
(factory applied coating)
Annex H (normative) - Simulated service test
(field joint)
Annex I (normative) - Simulated service test
(subsea equipment)
Annex J (normative) - Ring shear test procedure
Annex K (informative) - End of life through
thickness water profile calculation
BS EN ISO 12736
| Committee |
PSE/17/2
|
| DocumentType |
Draft
|
| Pages |
88
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN ISO 12736 : DRAFT 2011 | Identical |
| ISO/TR 15235:2001 | Preparation of steel substrates before application of paints and related products — Collected information on the effect of levels of water-soluble salt contamination |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| ISO 2063:2005 | Thermal spraying — Metallic and other inorganic coatings — Zinc, aluminium and their alloys |
| ISO 21809-2:2014 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings |
| ISO 8502-3:2017 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) |
| ISO 15711:2003 | Paints and varnishes — Determination of resistance to cathodic disbonding of coatings exposed to sea water |
| ISO 8502-4:2017 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 4: Guidance on the estimation of the probability of condensation prior to paint application |
| ASTM D 429 : 2014 : REDLINE | Standard Test Methods for Rubber Property—Adhesion to Rigid Substrates |
| ASTM D 4889 : 2015 : REDLINE | Standard Test Methods for Polyurethane Raw Materials: Determination of Viscosity of Crude or Modified Isocyanates |
| ISO 3219:1993 | Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate |
| ISO 2808:2007 | Paints and varnishes — Determination of film thickness |
| ISO 4892:1981 | Plastics — Methods of exposure to laboratory light sources |
| ISO 21809-1:2011 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 1: Polyolefin coatings (3-layer PE and 3-layer PP) |
| ISO 4590:2016 | Rigid cellular plastics — Determination of the volume percentage of open cells and of closed cells |
| ISO 1827:2016 | Rubber, vulcanized or thermoplastic — Determination of shear modulus and adhesion to rigid plates — Quadruple-shear methods |
| ISO 6502:2016 | Rubber — Guide to the use of curemeters |
| ASTM D 5289 : 2017 : REDLINE | TEST METHOD FOR RUBBER PROPERTY - VULCANIZATION USING ROTORLESS CURE METERS |
| ISO 14896:2009 | Plastics — Polyurethane raw materials — Determination of isocyanate content |
| ISO 8302:1991 | Thermal insulation — Determination of steady-state thermal resistance and related properties — Guarded hot plate apparatus |
| ISO 4897:1985 | Cellular plastics — Determination of the coefficient of linear thermal expansion of rigid materials at sub-ambient temperatures |
| ISO 8301:1991 | Thermal insulation — Determination of steady-state thermal resistance and related properties — Heat flow meter apparatus |
| ISO 1183:1987 | Plastics — Methods for determining the density and relative density of non-cellular plastics |
| ISO 4624:2016 | Paints and varnishes — Pull-off test for adhesion |
| ISO 8510-2:2006 | Adhesives — Peel test for a flexible-bonded-to-rigid test specimen assembly — Part 2: 180° peel |
| ISO 21809-3:2016 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings |
| ISO 2178:2016 | Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method |
| ISO 62:2008 | Plastics — Determination of water absorption |
| ISO 8502-6:2006 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 6: Extraction of soluble contaminants for analysis — The Bresle method |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| ISO 8502-9:1998 | Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 9: Field method for the conductometric determination of water-soluble salts |
| ISO 20340:2009 | Paints and varnishes — Performance requirements for protective paint systems for offshore and related structures |
| ISO 2884:1974 | Paints and varnishes — Determination of viscosity at a high rate of shear |
| EN 253:2009+A2:2015 | District heating pipes - Preinsulated bonded pipe systems for directly buried hot water networks - Pipe assembly of steel service pipe, polyurethane thermal insulation and outer casing of polyethylene |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 844:2014 | Rigid cellular plastics — Determination of compression properties |
| ISO 1133:2005 | Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
| ISO 814:2017 | Rubber, vulcanized or thermoplastic — Determination of adhesion to metal — Two-plate method |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic — Determination of density |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.