11/30205541 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 54-7 - FIRE DETECTION AND FIRE ALARM SYSTEMS - PART 7: SMOKE DETECTORS - POINT DETECTORS USING SCATTERED LIGHT, TRANSMITTED LIGHT OR IONISATION
Hardcopy , PDF
English
18-05-2015
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Tests
6 Evaluation of conformity
Annex A (normative) - Smoke tunnel for response value
measurements
Annex B (normative) - Test aerosol for response value
measurements
Annex C (normative) - Smoke measuring instruments
Annex D (normative) - Apparatus for dazzling test
Annex E (informative) - Apparatus for impact test
Annex F (normative) - Fire test room
Annex G (normative) - Smouldering (pyrolysis) wood
fire (TF2)
Annex H (normative) - Glowing smouldering cotton
fire (TF3)
Annex I (normative) - Flaming plastics (polyurethane)
fire (TF4)
Annex J (normative) - Flaming liquid (n-heptane)
fire (TF5)
Annex K (informative) - Information concerning the
construction of the smoke tunnel
Annex L (informative) - Information concerning the
requirements for the response to slowly
developing fires
Annex M (informative) - Information concerning the
construction of the measuring ionization chamber
Annex N (normative) - Additional requirements and
test methods for smoke detectors with more
than one smoke sensor
Annex O (normative) - Test set-up for testing the
protection against the effect of moving objects
Annex P (normative) - Apparatus open detector
static object test
Annex ZA (informative) - Clauses of this European
Standard addressing the provisions of the
EU Construction Products Directive (89/106/EEC)
BS EN 54-7
| Committee |
FSH/12/2
|
| DocumentType |
Draft
|
| Pages |
82
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 54-7 : DRAFT 2015 | Identical |
| ISO 209-1:1989 | Wrought aluminium and aluminium alloys — Chemical composition and forms of products — Part 1: Chemical composition |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| HD 323.2.3 : 200S2 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST CA - DAMP HEAT, STEADY STATE |
| IEC 60068-2-3:1969 | Basic environmental testing procedures - Part 2-3: Tests - Test Ca: Damp heat, steady state |
| IEC 60068-2-42:2003 | Environmental testing - Part 2-42: Tests - Test Kc: Sulphur dioxide test for contacts and connections |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 54-1:2011 | Fire detection and fire alarm systems - Part 1: Introduction |
| HD 323.2.56 : 200S1 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - DAMP HEAT, STEADY STATE, PRIMARILY FOR EQUIPMENT |
| IEC 60068-2-56:1988 | Environmental testing - Part 2: Tests. Test Cb: Damp heat, steady state, primarily for equipment |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.