11/30237753 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 17484-1 - PLASTICS PIPING SYSTEMS - MULTILAYER PIPE SYSTEMS FOR INDOOR GAS INSTALLATIONS WITH A MAXIMUM OPERATING PRESSURE UP TO AND INCLUDING 5 BAR (500 KPA) - PART 1: SPECIFICATIONS FOR SYSTEMS
Hardcopy , PDF
English
31-05-2014
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Requirements for the system
5 Pipes
6 Fittings
7 Fitness for purpose
8 Marking and documentation
Annex A (normative) - List of the reference product
standards
Annex B (normative) - Test for delamination and
strength of the joint line
Annex C (normative) - Resistance to gas constituents
Annex D (normative) - Thermal durability of the
outer layer of M-pipes
Annex E (normative) - Adhesion test
Annex F (normative) - Odour permeability
Annex G (normative) - Resistance to tensile load on
joints
Annex H (normative) - Crush test on joints
Annex I (normative) - Impact resistance test on joints
Annex J (normative) - Thermal cycling test on joints
Annex K (normative) - Repeated bending test
Bibliography
BS ISO 17484-1
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
44
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| ISO 10146:1997 | Crosslinked polyethylene (PE-X) pipes — Effect of time and temperature on the expected strength |
| ISO 6447:1983 | Rubber seals — Joint rings used for gas supply pipes and fittings — Specification for material |
| ISO 8085-3:2001 | Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels — Metric series — Specifications — Part 3: Electrofusion fittings |
| ISO 14531-1:2002 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 1: Pipes |
| ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series |
| DVGW W 542 : 2009 | COMPOUND PIPES IN THE DRINKING WATER INSTALLATION; REQUIREMENTS AND TESTING |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 17456:2006 | Plastics piping systems — Multilayer pipes — Determination of long-term strength |
| ISO 3:1973 | Preferred numbers — Series of preferred numbers |
| ISO/TS 10839:2000 | Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation |
| EN 713:1993 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ISO 24033:2009 | Polyethylene of raised temperature resistance (PE-RT) pipes — Effect of time and temperature on the expected strength |
| ISO 14531-3:2010 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 3: Fittings for mechanical jointing (including PE-X/metal transitions) |
| ISO/TR 10837:1991 | Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings |
| ISO 10508:2006 | Plastics piping systems for hot and cold water installations — Guidance for classification and design |
| ISO 11357-6:2008 | Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 14531-2:2004 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 2: Fittings for heat-fusion jointing |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 13480:1997 | Polyethylene pipes — Resistance to slow crack growth — Cone test method |
| ISO 18225:2012 | Plastics piping systems — Multilayer piping systems for outdoor gas installations — Specifications for systems |
| ISO 10147:2011 | Pipes and fittings made of crosslinked polyethylene (PE-X) — Estimation of the degree of crosslinking by determination of the gel content |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 17454:2006 | Plastics piping systems — Multilayer pipes — Test method for the adhesion of the different layers using a pulling rig |
| EN 12117:1997 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| ISO 13951:2015 | Plastics piping systems — Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| ISO 6957:1988 | Copper alloys — Ammonia test for stress corrosion resistance |
| ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels — Metric series — Specifications |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| ISO 3503:2015 | Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under internal pressure of assemblies subjected to bending |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.